• Journal of Biosystems Engineering
• /
• v.29 no.1
• /
• pp.37-44
• /
• 2004

This study was conducted to develop a new drying method far reducing the drying cost and time and to investigate the drying characteristics of oak mushroom. A far infrared dryer of down draft air flow type used for this experiment can control the drying parameters, such as far infrared heater temperature and aeration velocity. The far infrared drying tests were performed at aeration velocities of 0.3 and 0.6m/s under the temperature of 90 and 100$^{\circ}C$ in for infrared heater, respectively. The results were compared and analyzed with those of an heated air drying method used as a control in terms of properties representing the drying characteristics. such as shrinkage rate, color, energy consumption amino acid components, drying rate and moisture ratio. The results obtained from this research can be summarized as follows. 1. The drying rate of far infrared drying was faster than that of heated air drying. With high temperature of far infrared heater and slow aeration velocity, the far infrared drying of down draft air flow type was superior to the heated air drying. 2. Most of far infrared drying conditions required less energy consumption than heated air drying. 3. The shrinkage rates of heated air drying and far infrared drying were decreased by 17.0% and 18.2∼19.8%, respectively. 4. The difference of color on oak mushroom surface before and after drying can be represented as $\Delta$E. $\Delta$E values of far infrared drying and heated air drying were 2.39∼4.55 and 6.77, respectively. 5. The amounts of free amino acids were higher in the far infrared than in the heated air drying. In addition the amounts of Gln and Glu generally were increased and those of Ala, Leu, and Val were decreased in order.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4A
• /
• pp.373-384
• /
• 2009

For the first step on the quantitative evaluation of shrinkage reduction and differential shrinkage analysis of lightweight aggregate concrete, this study sets the moisture transport model of concrete by pre-absorbed water of porous lightweight aggregates and measured effective moisture diffusion coefficient, moisture capacity, degree of humidity supply and degree of humidity consumption by water binder ratio and aggregate type. The effective moisture diffusion coefficient in steady state caused by humidity difference between inside and outside of concrete had low value as low water-binder ratio. And in case of same water-binder ratio, effective moisture diffusion of mixtures used normal aggregates were lower than those used lightweight aggregates. To determine moisture store capability of concrete - moisture capacity, moisture contents were measured in 9 humidity conditions. As a result moisture contents of mixtures used lightweight aggregates was higher than mixtures used normal aggregates in all humidity conditions. This study measured lightweight aggregates' degree of humidity supply that applicable to normal atmospheric environment (above RH 50%) and made it quantitatively. Also amount of moisture release was set as a exponential function that represents a clear trend proportion to time and inverse proportion to humidity of the surroundings. As the result of measurement about degree of moisture consumption inside concrete following the internal consumption caused by cement hydration self-drying, it was showed that rapid decrease of humidity, around 10%, at early ages (7~10 days) when water-binder ratio is 0.3 and slow decrease around 5% and 1% when water-binder ratio is 0.4 and 0.5.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.2
• /
• pp.143-150
• /
• 2010

Purpose: The purpose of this study is to fabricate the new zirconia block (CNU block) and to evaluate fit of core and porcelain veneered zirconia crown. Material and methods: The experimental blocks were fabricated from the commercial ytrria-stabilized zirconia powder (KZ-3YE Type A). The powder was uniaxial pressing and the green bodies were conducted using the Cold Isostatic Pressing. The zirconia blocks were presintered at $1040^{\circ}C$ and the final sintering was performed at $1450^{\circ}C$. The Kavo Everest ZS $blank{(R)}$ (KaVo, Biberach/ $Ri{\beta}$.) was used as a control group. The linear shrinkage of CNU block and Kavo block were compared. Twenty-one cores for porcelain veneered crowns were fabricated with CAD/CAM system ($Everest{(R)}$, Biberach/ $Ri{\beta}$.). Group I; seven cores fabricated from Kavo blocks, Group II; seven cores fabricated from CNU blocks, Group III; seven cores from CNU blocks and porcelain veneering for crowns. All specimens were cemented and sectioned into two planes; diagonal and bucco-lingual. The measurement of the marginal, internal, and occlusal fit was carried out using SEM ($S-4800^{(R)}$) at $30{\times}$. The results were analyzed by one-way ANOVA test. Results: The linear shrinkage of the CNU block and the KaVo block was 19.00% and 20.09%. The marginal gap of cores ($29.67{\pm}6.58{\mu}m$) fabricated from CNU blocks showed significantly smaller than that of the cores of Kavo blocks ($36.84{\pm}7.18{\mu}m$) (P < .05). The internal gaps of the porcelain veneered crowns ($32.23{\pm}6.33{\mu}m$) were larger than those of the other two groups ($37.57{\pm}6.81{\mu}m$ and $38.14{\pm}6.81{\mu}m$). Conclusion: No statistically significant difference was found in between experimental groups and control group. The experimental groups in marginal gap showed significantly smaller than the control group.

• Restorative Dentistry and Endodontics
• /
• v.35 no.2
• /
• pp.125-133
• /
• 2010

Objectives: Rapid polymerization of overlying composite resin causes high polymerization shrinkage stress at the adhesive layer. In order to alleviate the shrinkage stress, increasing the light intensity over the first 5 seconds was suggested as an exponential curing mode by an LED light curing unit (Elipar FreeLight2, 3M ESPE). In this study, the effectiveness of the exponential curing mode on reducing stress was evaluated with measuring microtensile bond strength of three adhesives after the overlying composite resin was polymerized with either continuous or exponential curing mode. Methods: Scotchbond Multipurpose Plus (MP, 3M ESPE), Single Bond 2 (SB, 3M ESPE), and Adper Prompt (AP, 3M ESPE) were applied onto the flat occlusal dentin of extracted human molar. The overlying hybrid composite (Denfil, Vericom, Korea) was cured under one of two exposing modes of the curing unit. At 48h from bonding, microtensile bond strength was measured at a crosshead speed of 1.0 mm/min. The fractured surfaces were observed under FE-SEM. Results: There was no statistically significant difference in the microtensile bond strengths of each adhesive between curing methods (Two-way ANOVA, p > 0.05). The microtensile bond strengths of MP and SB were significantly higher than that of AP (p < 0.05). Mixed failures were observed in most of the fractured surfaces, and differences in the failure mode were not observed among groups. Conclusion: The exponential curing method had no beneficial effect on the microtensile dentin bond strengths of three adhesives compared to continuous curing method.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.6
• /
• pp.1010-1020
• /
• 1997

For this study, we did needlework of the sample considering practical aspects of production and consumption of silk, high-quality material for women's clothes, and then analyzed the state of the seam puckering after press and dry cleaning, estimated the Seam Puckering based on the mechanical properties of silk related to machine sewing, and examined the effects which Mechanical Properties have on Seam Puckering closely. Through this, we reach the following conclusion. 1. There are three types of seam puckering for each stage, which are caused bathe smoothness of the surface by press, and the difference between the shrinkage rates of fabric and sewing thread by Dry Cleaning. 2. In analyzing seam puckering classified by each step, seam puckering after sewing the fabric is related to WT negatively, while to RT and W positively. Seam puckering after sewing and pressing the fabric is related to WT, RC, MMD negatively and seam puckering after sewing, pressing anddry cleaning the fabric isrelated to WT negatively, too. 3. Concerning the mechanical properties of the sample with a little seam puckering, WT, LC, WC, RC, MMD, SMD is relatively large while RT, B, 2HB is small. 4. Judging from the result of estimating seam puckering based on mechanical properties, the estimate-formula is satisfied in this study.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.1
• /
• pp.39-48
• /
• 2020

The present study investigates the chemical reaction and performance of ternary blended binders by mixing ferronickel slag. Cement was replaced using ground granulated blast furnace slag and ferronickel slag, combined up to 50% of the replacement rate. The blended cements were tested by setting times, length change, compressive strength at 1, 3, 7, 28 days. X-ray diffraction and scanning electron microscope were conducted for detecting hydration products while the MIP and microhydation heat were used for examining morphological characteristics. The results showed that by adding ferronickel slag, Pozzolanic reaction occurred, forming a dense pore structure and the effect of reducing hydration heat and dry shrinkage was also found. The compressive strength at 28 days was lower than that of 100% OPC control specimen (OSP0), but ternary blended cements showed no significant difference compared to binary blended (OSP50). If the optimal mix is derived later and used for the purpose, the potential for use as a cement binder is expected.

• Nuclear Engineering and Technology
• /
• v.49 no.7
• /
• pp.1524-1536
• /
• 2017

During the fabrication process of reactor vessel head penetration (RVHP), the grain size of the tube material can be changed by hot or cold work and the inner side of the tube can also be shrunk due to welding outside of the tube. Several nonregular time-of-flight diffraction (TOFD) signals were found because of deformed grains. In this paper, an investigation of nonregular TOFD indications acquired from RVHP tubes using experiments and computer simulation was performed in order to identify and distinguish TOFD signals by coarse grains from those by Primary Water Stress Corrosion Crack (PWSCC). For proper understanding of the nonregular TOFD indications, microstructural analysis of the RVHP tubes and prediction of signals scattered from the grains using Finite Element Method (FEM) simulation were performed. Prediction of ultrasonic signals from the various sizes of side drilled holes to find equivalent flaws, determination of the size of the nonregular TOFD indications from the coarse grains, and experimental investigation of TOFD signals from coarse grain and shrinkage geometry to identify PWSCC signals were performed. From the computer simulation and experimental investigation results, it was possible to obtain the nonregular TOFD indications from the coarse grains in the alloy 690 penetration tube of RVHP; these nonregular indications may be classified as PWSCC. By comparing the computer simulation and experimental results, we were able to confirm a clear difference between the coarse grain signal and the PWSCC signal.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.3
• /
• pp.236-245
• /
• 2002

The acrylic resin was first introduced as denture base materials in 1937 and it is commonly used for denture base fabrication nowadays. Three different curing cycles (Conventional curing cycle, short curing cycle and long curing cycle) and three commercially available heat-activated acrylic resins (Vertex RS, Lucitone 199 and ProBase Hot) were investigated to find the curing cycle and material that showed the minimum shrinkage of the resin during polymerization process. A brass master mold was fabricated and duplicated by additional silicone impression material. Stone molds were made by pouring of type III dental stone (SILKY-ROCK YELLOW, Whip-Mix, Louisville, Kentucky). It was embedded in the flask. Strain gauge and thermocouple were embedded in the specimen. Strain gauge and thermocouple were connected to signal conditioning amplifier and data was recorded by pre-programmed software. The parameters ESmax (Maximum expansion strain), Sb (Strain measured just before deflasking procedure), Sa (Strain measured just after deflasking procedure) and Sf (Strain measured at the end of the experiment) were measured. ${\Delta}$S was calculated from Sb and Sa (${\Delta}$S=Sb-Sa). In the experiment concerned about materials, the parameters 90-ESmax (Maximum expansion strain measured during early 90 minutes of curing procedure), 180-ESmax (Maximum expansion strain measured from 90 minutes to 180 minutes), Sb, Sa, ${\Delta}$S and Sf were measured and the following conclusions were made. 1. The ESmax value of conventional curing cycle showed the largest value and the 180-ESmax value of Lucitone 199 showed the smallest value. 90-ESmax values showed no significant difference (p<0.05). 2. ${\Delta}$S values of conventional curing cycle showed the positive values. ${\Delta}$S values of short curing cycle and long curing cycle showed the negative values. All three materials cured by conventional curing cycle showed the positive values. 3. The Sf values of long curing cycle and ProBase Hot (cured by conventional curing cycle) showed the smallest values.

• Journal of Technologic Dentistry
• /
• v.41 no.4
• /
• pp.271-278
• /
• 2019

Purpose: To quantify the effect of the crystallization process on lithium disilicate ceramic crowns that are fabricated using a computer-aided design/computer-aided manufacturing(CAD/CAM) system, and to determine whether they are clinically acceptable by comparing values before and after the crystallization process. Methods: The maxillary first molar was selected as the abutment for the experiments. Ten working models were prepared. Marginal and internal gap of 4 groups of lithium disilicate crowns(n=10) fabricated with conventional method. Comparison was performed using the silicone replica technique and 3D superimposition analysis. The marginal and internal gaps of the restoration were measured before and after the crystallization process of this prosthesis. The average value of each part(the average of values measured before and after the crystallization) was statistically analyzed using paired t-test(α=0.05). Results: The results from the second phase of this research, which compared the average value of the gap between the marginal and internal fits of the lithium disilicate single crown before and after the crystallization process, indicated that the marginal gap was larger and the internal gap was smaller after the crystallization process, and this difference was statistically significant (P<0.05) in all the parts evaluated. Conclusion: While the shrinkage that occurs during crystallization does affect the marginal and internal fit of the prosthesis, it cannot be concluded to be a major effect because the resultant distortion was within the clinically acceptable range.

• Journal of Conservation Science
• /
• v.17 s.17
• /
• pp.19-32
• /
• 2005

The exterior of Korean traditional wooden buildings have been painted with Danchung of painting method using glue and pigments. However because of losing traditional techniques and materials through the period of colonization and industrialization, many problems are occurring today. Especially after several years from painting, occurrence of scalings and flakings in painting layer is a serious problem. To improve weathering resistance of painting layer caused by stress from the difference of swelling and shrinkage between painting layer and wood plate, was examined by weathering tests. The stress is due to the hydrophilic property of wood, mechanical properties(tensile property and stress relaxation) of painting layer, and priming methods by various binders such as glue, acrylic emulsion(Primal AC-3444), acrylic resin(Paraloid B-72). Because stress relaxation of acrylic emulsion of which glasf transition temperature is below room temperature$(7^{\circ}C)$ is high, painting layers with acrylic emulsion generate no scalings and flakings and are in the most durable state in all weathering tests. Priming method which starts from low concentration to high concentration, is more effective to improve durability than other priming methods.