• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.60-67
• /
• 2018

In the present study, when the surface of kenaf, which is an environmentally friendly natural fiber, was treated by using adhesive solution containing Chemlok 402, the effects of fiber surface treatment, fiber content and fiber length on the cure characteristics, hardness, tensile modulus and abrasion resistance of kenaf/natural rubber composites were investigated. The kenaf fiber contents consisting of the composites were varied with 0, 5, 10, 15, and 29 phr at a fixed fiber length of 2 mm and also the fiber length was varied with 2, 35, and 70 mm at a fixed fiber content of 5 phr. The Tmax and tc90 values, Shore A hardness, tensile modulus, and abrasion resistance of natural rubber composites strongly depended on the kenaf fiber content and length. The characteristics of the composite with kenaf fibers treated with the adhesive solution containing Chemlok 402 were higher than those untreated. This is ascribed to the improved interfacial adhesion between the treated kenaf fiber and the rubber matrix. This study suggests that an appropriate use of adhesive solution may be possible to increase the properties of natural fiber-reinforced composites.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.308-314
• /
• 2009

The acrylic rubber was synthesized by emulsion polymerization using n-butyl acrylate, n-butyl methacrylate, acrylonitrile, glycidylmethacrylate, and allyl methacrylate. When the contents of acrylonitrile were increased at fixed amount of crosslinking monomers, the Tg of polymers was increased with the contents of acrylonitrile, Mooney viscosity, hardness, and tensile strength also were increased. But the elongation was decreased due to the reduction of chain flexibility. The addition of the monomer for crosslinking, glycidylmethacrylate whose Tg is $56^{\circ}C$ resulted in the increased Tg of the polymer, and increased Mooney viscosity, hardness, and tensile strength, but the elongation at break was decreased with the glycidylmethacrylate contents. It was shown that this phenominon was attributed to the increment of crosslinking density by glycidylmethacrylate through the measurement of rheometer.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.2
• /
• pp.204-209
• /
• 2017

In order to use PUR/CuO Composites as the sealing materials for ships equipment, this research has been performed. PUR/CuO composites are produced by using ultrasonic waves. The increase of CuO leads to increase in the tensile strength and shore hardness. The cumulative wear volume shows a tendency to increase in proportional to sliding distance. As the CuO particles of these composites indicated, the friction coefficient was slightly increased. The major failure mechanisms were lapping layers, deformation of matrix, plowing, debonding of particles and microcracking by scanning electric microscopy photograph of the wear tested surface.

• Journal of the Korean Ceramic Society
• /
• v.29 no.5
• /
• pp.396-402
• /
• 1992

Carbon solid was prepared from dormant mesophase pitch (DMPP) without using a binder and its properties were characterized. DMPP powder was stabilized with air or nitric acid in pretreatment stage so that it might not soften in later heat ttreatment stage. Optimum sintering properties were obtained from carbon powder with 2.36∼2.38 of C/H atomic ratio and 1.27∼1.40 of C/O atomic ration in air stabilization. In nitric acid stabilization, optimum sintering properties were obtained when 20∼40 vol.% of nitric acid solution was used. Compressive strength increased up to 1200$^{\circ}C$ of heat treatment temperature, and the highest compressive strength and bulk density of carbon solid from DMPP were 3000 kgf/㎤, respectively. The optical properties of carbon solid obtained was fine mosaic structure. Carbon solid after graphitization showed the properties of hard carbon due to stabilization and its shore hardness was 120.

• Macromolecular Research
• /
• v.11 no.3
• /
• pp.198-201
• /
• 2003

Aqueous emulsion of polyurethane (PU) ionomers were reinforced with hydrophobic nanosilica to give composites. The aqueous emulsion was stable and the particle size increased as the content of hydrophobic nanosilica was increased. The reinforcing effect of nanosilica in mechanical properties of these composites were examined by dynamic mechanical and tensile tests, and the Shore A hardness was measured. Enhanced thermal and water resistance and marginal reduction in transparency of these composites were observed compared with pristine polymer. These results were similar with those of our previous studies on waterborne PU/organoclay nanocomposites.

• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.985-990
• /
• 2003

By heat treating coal tar pitch between 450∼500$^{\circ}C$, mesophase pitch could be obtained. Subsequently, this pitch was oxi-stabilized between 160∼240$^{\circ}C$ in air for the purpose of reducing swelling and distortion. The mechanism of stabilization was analysed using the thermo-gravity and FT-IR. To investigate the effect of oxi-stabilization, the shore hardness and bending stress were measured with carbonized green body which was made from oxi-stabilized coal tar pitch.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.279-285
• /
• 2019

Bio-based polyester polyols were synthesized using esterification with azelaic acid, sebacic acid, and 1,3-propanediol. Polyurethanes were prepared using chain extenders (1,4-Butanediol, 1,3-Propanediol, and isosorbide) and 4,4'-diphenylmethane diisocyanate with a mixing ratio of 1:1:1.1. Subsequently, the properties of the polymers prepared using the different chain extenders were compared. The synthesis of polyurethane was confirmed by FT-IR, TGA, and GPC. The mechanical properties (hardness, ball rebound, and tensile strength) of the materials were analyzed using shore A tester, taber abrasion, and UTM. heat, chemical, and water resistances of the prepared materials were measured by comparing the tensile strengths according to external changes.

• The Journal of Advanced Prosthodontics
• /
• v.11 no.1
• /
• pp.32-40
• /
• 2019

PURPOSE. The purpose of this study was to compare mechanical and physical properties of injection-molded thermoplastic denture base resins. MATERIALS AND METHODS. In this study, six commercially available products (VA; Valplast, LC; Lucitone, ST; Smiltone, ES; Estheshot-Bright, AC; Acrytone, WE; Weldenz) were selected from four types of thermoplastic denture base materials (Polyamide, Polyester, Acrylic resin and Polypropylene). The flexural properties and shore D hardness have been investigated and water sorption and solubility, and color stability have evaluated. RESULTS. For the flexural modulus value, ES showed the highest value and WE showed significantly lower value than all other groups (P<.05). Most of experimental groups showed weak color stability beyond the clinically acceptable range. CONCLUSION. Within the limits of this study, thermoplastic denture base resin did not show sufficient modulus to function as a denture base. In addition, all resins showed discoloration with clinical significance, and especially polyamides showed the lowest color stability.

• The Journal of Engineering Geology
• /
• v.14 no.4 s.41
• /
• pp.401-416
• /
• 2004

We have collected shale specimens from the Pungam Basin in Kangwon province and investigated change of physical properties by freezing and thawing in water as well as in acidic fluid. The temperature range was $-20{\pm}2^{\circ}C\~15{\pm}2^{\circ}C$. Specimens were frozen for 12 hours and thawed in water for 8 hours. Then, they were saturated in the vacuum chamber for 4 hours to make specimens fully saturated. This procedure was 1 cycle. We have measured absorption, ultrasonic velocity, shore hardness, slake durability and uniaxial compressive strength at every 5th cycles. The physical properties increased or decreased as freezing and thawing cycles increased. Uniaxial compressive strength decreased by 0.40MPa per cycle in water and by 0.48MPa in acidic fluid. Elastic constant also decreased by 0.21GPa per cycle in water and by 0.30GPa in acidic fluid. Absorption increased by $0.29\%$ and $0.37\%$ per cycle in water and acidic fluid, respectively. These results indicate that decrease in uniaxial compressive strength, elastic constant and absorption by freezing and thawing in acidic fluid is more rapid than in water. Ultrasonic velocities, shore hardness and slake durability show no differences in water and acidic fluid. When we compared our results with the temperatures in the Hongchon during the winter season, $6\~12$ cycles may be equivalent to 1 year.

• Polymer(Korea)
• /
• v.27 no.5
• /
• pp.470-476
• /
• 2003

In order to obtain high refractive plastic materials, 1,2 -ethylenedisulfanylbis(2-mercaptomethyl-1-ethanthiol) (ESTT) was newly prepared in good yield by the reaction of 1,2-ethylenedisulfanylbis(2-bromomethyl-1-ethanthiol) (ESTB) with thiourea followed by hydrolysis using an aqueous ammonia solution and characterized by $^1$H-NMR (-SH at 1.7 ppm), $\^$13/C-NMR(-CH$_2$SH at 28.4 ppm) and FT-IR (-SH at 2540 cm$\^$-1/) spectroscopy, etc. Polythiourethanes (PTU) were obtained from the combinations of ESTT with each of 4,4＇-methylenebis(phenylisocyanate) (MDI), tolyene 2,4-diisocyanate (TDI), isophorone diisocyanate (IPDI), mxylene diisocyanate (XDI), and 1,6-diisocyanatohexane (HMDI) in the presence of dibutyltin dilaurylate as a catalyst, in a casting mold, and characterized by FT-IR (existence of N=C=O) spectroscopy and elemental analyzer (sulfur content). Accordingly, their thermal, mechanical and optical properties were investigated by using DSC, TGA, hardness tester and refractometer: both the melting point on DSC and crystallinity on X -ray diffraction (XRD) for specimens of PTUs were not observed. PTUs with T$\_$g/s above 110 $^{\circ}C$ showed good hardness (Shore D) in the range of 86 to 89. Thermal stabilities of PTUs obtained by using ESTT and each of diisocyanates containing aromatic rings were especially good. Also, the optical transmittances of amorphous PTUs through UV-visible source in the range of 400 to 600 nm were good. PTUs showed refractive indexes above 1.60, and their refractive indexes gradually increased with increase of sulfur contents.