• 제목/요약/키워드: shore D hardness

검색결과 15건 처리시간 0.019초

부가중합형 실리콘 교합인기재의 탄성 특성 (Elastic properties of addition silicone interocclusal recording materials)

  • 이영옥;김경남
    • 한국치위생학회지
    • /
    • 제12권3호
    • /
    • pp.513-520
    • /
    • 2012
  • Objectives : In this study, contact angle and shore D hardness were measured, and a shark fin test was conducted after selecting five addition silicon(Blu-Mousse, BM; EXABITE II, EX; PERFECT, PF; Regisil$^{(R)}$ Rigid, RE; Silagum$^{(R)}$, SI) in order to figure out the properties of elastomeric interocclusal recording materials and reduce errors at interocclusal recording. 8) Methods : A contact angle was measured using a contact angle analyzer. After placing a drop of liquid on the surface of the specimens of interocclusal recording materials, a contact angle was photographed with a CCD camera on the equipment. In terms of a shark fin test, interocclusal recording materials were mixed for the time proposed by the manufacturer and inserted into the split ring of the Shark fin device. Twenty (20) seconds exactly, a metal rod was removed to make the materials slowly absorbed. Once they hardened, fin height was measured with a caliper after separating molds and trimming the specimens. The shore D hardness was measured with a shore D hardness tester(Model HPDSD, Hans Schmidt & Co. Gmbh, Germany) in sixty (60) minutes after fabricating specimens. In each experiment, five specimens, mean and standard deviation were calculated. A one-way ANOVA test was performed at the p>0.05 level of significance. In terms of correlation among the tests, Pearson correlation coefficient was estimated. For multiple comparison, Scheffe's test was carried out. Results : A contact angle was the highest in EX with $99.23^{\circ}$ (p<0.05) while the result of the shark fin test was the longest in RE with 5.45mm. SI was the lowest (0.27mm) with statistical significance. Among the interocclusal recording materials, significant difference was observed in terms of means (p<0.05). The shore D hardness was the highest in SI with 31.0 while RE was significantly low with 16.4 (p<0.05). Among the materials, statistically significant difference was observed in terms of means when compared to the rest materials (RE), BM, RE and SI (PF and EX) and the remaining materials (BM and SI) (p<0.05). In terms of correlations among the tests, a negative correlation occurred between shore D hardness and shark fin test(r=-0.823, p=0.000). Conclusions : According to the study above, it is necessary to understand the properties of interocclusal recording materials and consider contact angle, shark fin test and properties of shore D hardness to select appropriate materials.

Physical and electrical properties of PLA-carbon composites

  • Kang Z. Khor;Cheow K. Yeoh;Pei L. Teh;Thangarajan Mathanesh;Wee C. Wong
    • Advances in materials Research
    • /
    • 제13권3호
    • /
    • pp.211-220
    • /
    • 2024
  • Polylactic acid or polylactide (PLA) is a biodegradable thermoplastic that can be produced from renewable material to create various components for industrial purposes. In 3D printing technology, PLA is used due to its good mechanical, electrical, printing properties, environmentally friendly and non-toxic properties. However, the physical properties and excellent electrical insulation properties of PLA have limited its application. In this study, with the carbon black (CB) as filler added into PLA, the lattice spacing and morphology were investigated by using X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The physical properties of PLA-carbon composite were evaluated by using tensile test, shore D hardness test and density and voids measurement. Impedance test was conducted to investigate the electrical properties of PLA-Carbon composites. The results demonstrate that the inclusion of carbon black as filler enhances the physical properties of the PLA-carbon composites, including tensile properties, hardness, and density. The addition of carbon black also leads to improved electrical conductivity of the composites. Better enhancement toward the electrical properties of PLA-carbon composites is observed with 1wt% of carbon black in N774 grade. The N550 grade with 2wt% of carbon black shows better improvement in the physical properties of PLA-carbon composites, achieving 10.686 MPa in tensile testing, 43.330 in shore D hardness test, and a density of 1.200 g/cm3 in density measurement. The findings suggest that PLA-carbon composites have the potential for enhanced performance in various industrial applications, particularly in sectors requiring improved physical and electrical properties.

달리기 속도의 증가에 따른 운동화 중저의 경도와 신발바닥의 두께가 신발의 볼 굴곡각도에 미치는 영향 (The Influence of Midsole Hardness and Sole Thickness of Sport Shoes on Ball Flex Angle with the Increment of Running Velocity)

  • 곽창수;목승한;권오복
    • 한국운동역학회지
    • /
    • 제15권4호
    • /
    • pp.153-168
    • /
    • 2005
  • The purposes of this study were to determine the influence of midsole hardness and sole thickness of sports shoes on ball flex angle and position with increment of running velocity. The subjects employed for this study were 10 college students who did not have lower extremity injuries for the last one year and whose running pattern was rearfoot striker of normal foot. The shoes used in this study had 3 different midsole hardness of shore A 40, shore A 50, shore A 60 and 3 different sole thickness of 17cm, 19cm, 21cm. The subjects were asked to run at 3 different speed of 2.0m/sec, 3.5m/sec, 5.0m/sec and their motions were videotaped with 4 S-VHS video cameras and 2 high speed video cameras and simultaneously measured with a force platform. The following results were obtained after analysing and comparing the variables. Minimum angle of each ball flex position were increased with the increment of running velocity and shoe sole thickness(P<0.05), but mid-sole hardness did not affect minimum ball flex angle. The position which minimum angle was shown as smallest was 'D'. Midsole hardness and sole thickness did not affect time to each ball flex minimum angle, total angular displacement of ball flex angle, and total angular displacement of torsion angle(P<0.05). The position which minimum angle was appeared to be earliest was similar at walking velocity, and E and F of midfoot region at running velocity. Total angular displacement of ball flex position tended to increase as shifted to heel. It was found that running velocity had effects on ball flex angle variables, but shoe sole thickness partially affected. It would be considered that running velocity made differences between analysis variables at walking and running when designing shoes. Also, it was regarded that shoes would be developed at separated region, because ball flex angle and position was shown to be different at toe and heel region. It is necessary that midsole hardness and thickness required to functional shoes be analyzed in the further study.

가교 폴리에틸렌의 열노화에 따른 구조와 물성의 변화 (The Variation of Structure and Physical Properties of XLPE during Thermal Aging Process)

  • 이미영;김철환;구철수;김복렬;이영관
    • 폴리머
    • /
    • 제27권3호
    • /
    • pp.249-254
    • /
    • 2003
  • 가교 폴리에틸렌을 열을 가하여 노화시킨 후 구조 및 물성의 변화를 조사하였다. 가교 폴리에틸렌의 열적 산화 반응으로 카보닐 그룹이 형성됨을 X-선 광전자 분광법과 근적외선 분광법을 이용하여 확인하였다. 노화 시간이 길어질수록 1715 nm에서 관찰되는 카보닐 피이크가 정량적으로 증가하는 것을 근적외선 분광법을 이용하여 관찰하였다. 열화 시간에 따른 흡수 피이크의 선형적인 관계로부터 근적외선 분광법이 고분자 재료의 열화 과정을 감시하는데 적합한 방법임을 확인할 수 있었다. 또한 노화에 의한 가교 결합의 발생과 그에 따른 물리적 성질의 변화를 TMA, 응력-변형 시험, 쇼어 경도 측정 방법을 이용하여 관찰하였다. 노화가 진행됨에 따라 유리 전이 온도가 110에서 132$^{\circ}C$로 증가함을 관찰하였으며, 인장률은 265에서 110%로 점차 감소하고 쇼어 D 경도는 32에서 50으로 크게 증가하는 것을 관찰할 수 있었다.

진공사출금형용 STS316L 금속 다공체 제조 및 기계적 특성 (Fabrication and Mechanical Properties of STS316L Porous Metal for Vacuum Injection Mold)

  • 김세훈;김상민;노상호;김진평;신재혁;성시영;진광진;김태안
    • 한국분말재료학회지
    • /
    • 제22권3호
    • /
    • pp.197-202
    • /
    • 2015
  • In this study, porous stainless steel (STS316L) sintered body was fabricated by powder metallurgy method and its properties such as porosity, compressive yield strength, hardness, and permeability were evaluated. 67.5Fe-17Cr- 13Ni-2.5Mo (wt%) powder was produced by a water atomization. The atomized powder was classified into size with under $45{\mu}m$ and over $180{\mu}m$, and then they were compacted with various pressures and sintered at $1210^{\circ}C$ for 1 h in a vacuum atmosphere. The porosities of sintered bodies could be obtained in range of 20~53% by controlling the compaction pressure. Compressive yield strength and hardness were achieved up to 268 MPa and 94 Shore D, respectively. Air permeability was obtained up to $79l/min{\cdot}cm^2$. As a result, mechanical properties and air permeability of the optimized porous body having a porosity of 25~40% were very superior to that of Al alloy.

Effect of denture cleansers on surface hardness of resilient denture liners at various time intervals- an in vitro study

  • Pahuja, Rasleen Kaur;Garg, Sandeep;Bansal, Sanjay;Dang, Rajat Harvinder
    • The Journal of Advanced Prosthodontics
    • /
    • 제5권3호
    • /
    • pp.270-277
    • /
    • 2013
  • PURPOSE. This study was aimed to determine the effect of two chemically distinct denture cleansers and water on the surface hardness of acrylic and silicone based soft denture liners at various time intervals. MATERIALS AND METHODS. Two commonly used commercial resilient liner material were selected based on their chemical composition (silicone- and acrylic-based soft liners) for this investigation. 120 cylindrical specimens were made of $15mm{\times}10mm$ dimensions (according to ASTM: D-2240-64T) in a custom made metal mold. All specimens were stored in artificial saliva throughout the study. Forty specimens were cleansed daily in 0.5% sodium hypochlorite solution; forty were cleansed in sodium perborate and remaining forty specimens were daily rinsed in water. Testing was done at 1 week, 1 month, 3 months and 6 months for surface hardness using a Shore A Durometer. A mean of 3 reading for each sample was subjected to one-way ANOVA, Post Hoc test and pair-t test for statistical analysis. P values of less than 0.05 were taken as statistically significant. RESULTS. Surface hardness of all the samples was significantly higher after a period of 6 months irrespective of the cleansing treatment. Minor changes were observed between control, sodium hypochlorite and sodium perborate groups with time. Greater change was observed in surface hardness of acrylic-based soft denture liners as compared to silicone-based soft liners for all groups, as time progressed. CONCLUSION. Silicone-based soft denture liners performed significantly better in all cleansing treatments than acrylic-based soft denture liners.

Physical properties and color stability of injection-molded thermoplastic denture base resins

  • Song, So-Yeon;Kim, Kyoung-Soo;Lee, Jeong-Yol;Shin, Sang-Wan
    • The Journal of Advanced Prosthodontics
    • /
    • 제11권1호
    • /
    • pp.32-40
    • /
    • 2019
  • PURPOSE. The purpose of this study was to compare mechanical and physical properties of injection-molded thermoplastic denture base resins. MATERIALS AND METHODS. In this study, six commercially available products (VA; Valplast, LC; Lucitone, ST; Smiltone, ES; Estheshot-Bright, AC; Acrytone, WE; Weldenz) were selected from four types of thermoplastic denture base materials (Polyamide, Polyester, Acrylic resin and Polypropylene). The flexural properties and shore D hardness have been investigated and water sorption and solubility, and color stability have evaluated. RESULTS. For the flexural modulus value, ES showed the highest value and WE showed significantly lower value than all other groups (P<.05). Most of experimental groups showed weak color stability beyond the clinically acceptable range. CONCLUSION. Within the limits of this study, thermoplastic denture base resin did not show sufficient modulus to function as a denture base. In addition, all resins showed discoloration with clinical significance, and especially polyamides showed the lowest color stability.

새로운 폴리(티오우레탄)의 합성 및 특성 (Synthesis and Characterization of Novel Polythiourethanes)

  • 김경만;허영태;박인환;이범재
    • 폴리머
    • /
    • 제27권5호
    • /
    • pp.470-476
    • /
    • 2003
  • 고굴절률을 갖는 플라스틱 재료를 얻기 위하여 1,2-에틸렌디설파닐비스(2-머캅토메틸-1-에탄티올) (ESTT)을 1,2-에틸렌디설파닐비스(2-브로모메틸-1-에탄티올) (ESTB)과 티오우레아의 반응과 암모니아 용액으로 가수분해 반응을 해서 높은 수율로 새로이 합성하였고, $^1$H-NMR, $^{13}$C-NMR, FT-IR및 Mass Specooscopy 등에 의해 1.7 ppm에서 -SH, 28.4 ppm에서 -CH$_2$SH, 2540 $cm^{-1}$ /에서 -SH등의 관능기 구조를 확인하였다. 이어서, 폴리티오우레탄 (PTU)들은 디부틸틴 디라울레이트 존재하에서 ESTT와 4,4'-메틸렌비스(페놀이소시아네이트) (MDI), 톨릴렌 2,4-디이소시아네이트 (TDI), 이소포론 디이소시아네이트 (IPDI), m-자일렌디이소시아네이트 (XDI) 및 1,6-디이소시아네이토헥산 (HMDI) 등을 일정한 틀에 넣고 주형중합을 하고, FT-IR로 N=C=O의 존재를 확인하였다. 이어서, PTU 수지들의 열적, 기계적 및 광학적 성질을 살펴보기 위하여 열주사분석 (DSC)과 열중량분석 (TGA), 경도 및 굴절률 측정 등을 행하여, PTU 시편들이 DSC상에서 융점이 없고 XRD상으로 무정형임을 관찰하였다. 또, 110 $^{\circ}C$ 이상의 유리 전이 온도를 갖는 PTU 수지들은 86∼89 범위의 양호한 경도 (Shore D)를 나타냈으며, 방향족 고리를 함유하는 디이소시아네이트와 ESTT를 원료로 했던 PTU수지들의 내열성이 특별히 양호하였다. 무정형 PTU 수지들은 400∼600 m 범위의 UV-vis 광원에 의한 광투과율 들도 양호하게 나타났다. PTU 수지들은 1.60 이상의 굴절률을 보였으며, 황함량이 증가하면 굴절률도 점차 증가하는 것이 관찰되었다.

FCEV용 고압 밸브 실링부의 고무재질에 따른 기밀해석 (Sealing analysis of sealing rings with respect to rubber material properties for high pressure valve of FCEV)

  • 박근영;양갑진;노의동;박준수;전문수;이형욱
    • 융복합기술연구소 논문집
    • /
    • 제7권2호
    • /
    • pp.13-16
    • /
    • 2017
  • The design of sealing mechanisms of a manual pressure valve was analyzed with FE analysis for a hydrogen fuels charge and discharge system of FCEV. The damage prediction of the O-ring with respect to the material models of rubbers was calculated by the gap analysis of the backup ring and O-ring according to the internal pressure. Two kinds of the rubber material characteristic models were adopted to the O-ring. One was the linear elastic and the other was hyperelastic of Ogden $3^{rd}$ order model. The experimental data of urethane of Shore hardness 90 was utilized to the curve fitting of hyperelastic properties. It was found that the contact pattern of the backup ring was different in two models and the sealing mechanism was better in the case of the hyperelastic characteristic model.

세르샤 마모시험을 통한 암석의 마모도 측정에 관한 연구 (Determination of Rock Abrasiveness using Cerchar Abrasiveness Test)

  • 이수득;정호영;전석원
    • 터널과지하공간
    • /
    • 제22권4호
    • /
    • pp.284-295
    • /
    • 2012
  • 본 연구에서는 암석 절삭 장비의 마모에 직접적인 영향을 주는 인자인 암석의 마모도(abrasiveness) 측정에 관한 연구를 수행하였다. 몇 가지 방법 중 세르샤 마모 시험(Cerchar abrasiveness test)을 통하여 암석의 마모도에 영향을 미치는 인자를 확인하고 효율적인 시험을 수행하기 위한 조건들을 연구하였다. 국내 19종 암석에 대한 시험 결과를 통하여, 세르샤 마모 지수(CAI, Cerchar Abrasiveness Index)에 영향을 미치는 암석의 역학적 물성(단축압축강도, 간접인장강도, 탄성계수, 포아송비, 공극률, 쇼어경도)과의 상관관계를 찾아보았고 X선 회절 분석을 통하여 암석의 구성 광물 중 마모도에 가장 큰 영향을 미치는 석영 함량, 등가 석영 함량과의 관계도 확인하였다. 그 결과로 암석의 입자 결합 특성보다 광물의 특성이 CAI에 영향을 더 미치는 것으로 관찰되었고, 단축압축강도와 등가 석영함량의 함수로 CAI를 예측하는 모델을 제시하였으며 핀의 경도가 커질수록 CAI값이 선형적으로 작아짐을 확인하였다. 수치해석적 연구를 통해 세르샤 마모 시험을 모사한 결과 초기 긁힘 거리에서 대부분의 마모가 발생함을 확인하였고 하중이 증가할수록 CAI값이 증가함을 확인하였다.