• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.442-455
• /
• 2016

The resistance and seakeeping performance of a high-speed monohull vessel were investigated through a series of model tests in a towing tank. The hull had a slender wave-piercing bow, round bilge, and small deadrise angle on stern. Tests on the bare hull in calm water were first conducted and tests on spray rails followed. The spray rails were designed to control the flow direction and induce a hydrodynamic lift force on the hull bottom to reduce trim angle and increase rise of the hull. The maximum trim of the bare hull was $4.65^{\circ}$ at the designed speed, but the spray rails at optimum location reduced trim by $0.97^{\circ}$. The ship motion in head seas was examined after the calm water tests. Attaching the rails on the optimum location effectively reduced the pitch and heave motion responses. The vertical acceleration at the fore perpendicular reduced by 11.3%. The effective power in full scale was extrapolated from the model test results and it was revealed that the spray rails did not have any negative effects on the resistance performance of the hull, while they effectively stabilized the vessel in calm water and waves.

• Journal of Ocean Engineering and Technology
• /
• v.32 no.3
• /
• pp.158-165
• /
• 2018

Generally, container ships contain cargo holds with cell guides that serve to increase the container loading and unloading efficiency, minimize the space loss, and fix containers during the voyage. This paper describes a new quality management system for the cell guides of container ships (the so-called Trim Cell Guide system). The main functions of this system are the trimming of the point cloud obtained using a 3D scanner and an inspection simulation for cell guide quality. In other words, the raw point cloud of cell guides after construction is measured using a 3D scanner. Here, the raw point cloud contains a lot of noise and unnecessary information. Using the GUI interface supported by the system, the raw point cloud can be trimmed. The trimmed point cloud is used in a simulation for cell guide quality inspection. The RANSAC (Random Sample Consensus) algorithm is used for the transverse section representation of a cell guide at a certain height and applied for the calculation of the intervals between the cell guides and container. When the container hits the cell guides during the inspection simulation, the container is rotated horizontally and checked again for a possible collision. It focuses on a system that can be simulated with the same inspection process as in a shipyard. For a practicality review, we compared the precision data gained from an inspection simulation with the measured data. As a result, it was confirmed that these values were within approximately ${\pm}2mm$.

• Journal of the Korean Institute of Gas
• /
• v.17 no.2
• /
• pp.85-89
• /
• 2013

The purpose of the development of KC-1 LNG cargo containment system is reduction in royalty and increase in competitiveness of shipbuilding industry. An assessment of structure safety for LNG cargo containment system under sloshing load due to ship motion has become an important design element. The ideal way is to implement fully interaction of the fluid domain and the cargo containment system. However the irregular sloshing pressure were idealized in the form of a triangular wave for safety assessment because the fluid- structure interaction analysis is taken the extensive computation time and difficult to ensure the accuracy of the results. In this study, the sloshing load was assumed to be a triangular wave with a maximum pressure of 10 bar during 15/1000 seconds. In the analytic results, the basic insulation panel of KC-1 LNG cargo containment system was assessed to be structurally safe for sloshing load.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.233-239
• /
• 2014

The accurate engine output is basically one of important factors for the analysis of engine performance. Nowadays in-cylinder pressure analyzer in internal combustion engine is also an indispensable tool for engine research and development, environment regulation and maintenance of engine. The combustion analysis is desperately needed in order to induce a correct judgment on the condition of the engine and suggest the specific ways to improvement as well as the correct engine output. And these tool is advantageous to reduce fuel consumption and maintenance of the engine. In this study, using the developed measuring kit, combustion analysis of marine generator engine which was adapted as test engine was carried out. It was verified that the good operation condition of the engine as well as contributing to fuel savings by checking and readjusting accurately the irregular combustion of the test engine were accomplished. From the results all above, it was recognized that the measuring kit by new method for engine output was developed and verified for its utilities.

• Journal of Navigation and Port Research
• /
• v.29 no.1 s.97
• /
• pp.77-82
• /
• 2005

According as the quantity of goods transported by ship is increasing, a port environment is rapidly changing To meet this situation successfully, the development of the next generation port loading and unloading system(LMTT) is studied A Frame of shuttle car for LMTT(Linear Motor-based Transfer Technology) consists of three parts which are outer beam, inner beam and cross beam In this study, we carried out the finite element analysis for the effect of cross beam on the strength and stiffness of the frame according to the number of cross beam, loading position of container, the distance ratio of inner beam from center. The result is as follow ; When the load is applied on outer beam and inner beam concurrently and the number of cross beam is 5, that is the optimum condition in frame design.

• Journal of Navigation and Port Research
• /
• v.31 no.5 s.121
• /
• pp.403-408
• /
• 2007

The purpose of this paper is to show a way for measuring the rankings of efficient seaports in Korea by using DEA(data envelopment analysis) and model suggested by Jahanshahloo et al(2006). Two inputs(birthing capacity, and cargo handling capacity) and three outputs(export cargo handling amount, import cargo handling amount, and number of ship calls), and one cross sectional data(2004) for 26 Korean seaports are considered for measuring the efficiencies. An empirical main result indicates that ranking order of efficient seaports are Okpo, Samcheok Ulsan, Daesan, Busan, Gohyun Ports. Samcheok Port is classified as the most strong efficient port among 16 general ports except 10 container ports. The Korean seaport authority can adopt the new measurement way introduced in this paper for measuring the exact ranking order of efficient seaports when it decides the development and investment to each efficient seaport.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.5
• /
• pp.762-769
• /
• 2009

A canoe is one of the most popular boats in leisure on the water. Generally canoe has been built by good wooden strips. And canoe built by FRP is used for business recently. But by the users' demands for good quality and the restriction to environmental pollution the wooden canoes are required for personal and canoe building business. The modern wooden canoes were built by the strip construction method are used typically. However it is not suitable for the mass productivity requires effective resource operations and managements of men, materials, times, and price. On this paper the new construction method, called the piling-up laminated construction method, is studied to building a canoe using the piling-up with the laminated wooden plates gives more productivity than the others. First a canoe with various curved surfaces is designed from 3D design system. And the hull of canoe model is divided horizontally to generating the laminated plates that will be converting real wooden plates available from the market and will be routed by the manufacturing machine. After the simulating and analyzing of piling-up with the laminated plates, the canoe is building with less times, less men, less resources, and lower price than other method, avoid of the requirements of additional building tools. On the next paper the constructing of a real canoe using the manufactured wooden plates will be studied.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.3
• /
• pp.258-268
• /
• 2017

In this study, we aim to converge a technology for analyzing the hydraulic circuit of a loading arm with an- other one for analyzing multi-body dynamics by utilizing analysis software SimulationX. Further, this study intends to overcome the limitations of the existing technology for analyzing a hydraulic circuit with a variation at the rotation center of the moving mass and the difficulty of incorporating the behavior in a gravity field. First, the specifications of the hydraulic circuit components were reflected in an analysis model to secure reliability. Hydraulic circuit modeling was then performed using a single analysis model with a verified reliability. Subsequently, the multi-body system (MBS) model of the loading arm was formed. Finally, the analysis model of the hydraulic circuit and the MBS model were converged to check if the circuit analysis result was exactly reflected in the MBS model. The convergence analysis model has development cost-saving effect because it is capable of predicting the dynamic behavior of an object without the prototype.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.97-103
• /
• 2018

Force is a crucial element to be measured in various industries, especially the machine tool industry. Mega units of force are required in fields such as the heavy and ship industries. Micro/nano units of force are required for microparticles. The detection of force generates a physical transformation due to the force imposed from the outside, atlrnd electrical voltage signals are obtained from the system. For the detection of force, an octagonal ring load cell based on circular ring theory is designed and produced. To design the octagonal strain ring, theoretical values with data from the ANSYS program are compared to determine the size of the octagonal strain ring. An octagonal strain ring of the chosen size is made with the SCM415 material. The strain gauges are attached to the octagonal strain ring, designed to construct a full Wheatstone bridge. The LabVIEW program is used to measure the data, and strain values are found. With the octagonal ring load cell completed in this way, experiments are conducted by imposing forces on the tangential axis and radial axis. Experiments are performed to verify if the octagonal ring load cell conducts measurements properly, and theoretical values are analyzed to find any differences. The data will later be used in further research to develop a machine-tool dynamometer.

• Journal of Korea Water Resources Association
• /
• v.41 no.8
• /
• pp.785-795
• /
• 2008

The swell is a major cause of interruption for the activity in a port and the ship navigation in coastal waters, coastal geographical changes, and the disaster with a loss of lives. However, many researches about the observation and the prediction of swells have not been conducted actively due to the difficulties to collect and synthesize the massive amount of long term field data for waves and meteorological information. In this study, the internet-based realtime monitoring system(Fieldbox) was developed to collect the wave data. The characteristics and main components of swells occurred in Korea were analyzed using wave data observed through the Fieldbox and the meteorological data collected by the KMA(Korea Meteorological Administration) and NASA(National Aeronautics and Space Administration). The characteristics of the swell generation patterns were analyzed using the monthly data of the Kwangan Tower between 2004 and 2006 to estimate the specific features such as sources and locations of swells generated in Korea.