• 한국전산구조공학회논문집
• /
• 제21권3호
• /
• pp.253-263
• /
• 2008

IAI의 IFC를 기반으로 강 교량을 구성하는 부재의 상세 설계 정보를 표현하기 위한 방안을 제시하였다. 이를 위해 먼저 강교 부재 상세 설계와 관련한 설계기준, 구조계산서, 상세설계도면을 분석하여 실무에서 다루어지는 설계 데이터 항목과 이들의 표현방식을 분류하였다. 설계 항목을 기존 IFC 모델로 표현 가능한 것, 추가 모델이 필요한 것으로 나누었고, 보강재, 격벽, 현장 연결부, 그리고 전단연결재를 보다 체계적으로 표현하기 위한 속성 및 위상관계를 정립하였다. 마지막으로 본 연구를 통해 제시된 데이터모델을 기반으로 설계 정보 입력을 위한 프로그램을 구현하였다. 테스트용 교량에 적용하여 물리적 STEP 파일 생성함으로써 제시한 데이터 모델의 논리성을 확인하였다.

• Biomaterials and Biomechanics in Bioengineering
• /
• 제3권1호
• /
• pp.27-35
• /
• 2016

Anterior knee pain is a major problem among adolescents and young adults especially those who participates in sports. The most common pathogenesis of anterior knee pain can arise from compression and shear forces in the patellofemoral joint. It is also caused by impingement of infrapatellar fat pad. Fat pad impingement can occur when the fat pad becomes swollen and inflamed due to a direct blow or chronic irritation. As a result, the bottom tip (or inferior pole) of the patella can pinch the fat pad. One of the many causes of swollen fat pad can be secondary to anterior cruciate ligament (ACL) injury. The aim of this study was to compare the infrapatellar fat pad volume in patients with acute ACL injury and a group of age-, gender-, and activity- matched controls with intact ligament. Axial magnetic resonance (MR) images have been performed on 32 patients with torn ACL and 40 control patients. The volume of the fat pad was measured digitally from MR image by using a 3d Reconstruction software, ellipsoidal approximation, and a MATLAB code. The results were compared between patients with torn ACL and control group. Patients with a torn ACL had a significantly larger fat pad than the controls (P=0.01). There was no significant difference between the methods used to measure the infrapatellar fat pad volume (P=0.83-0.87). Thus, lesions of the infrapatellar fat pad is often associated with ACL injury.

• 한국지반환경공학회 논문집
• /
• 제9권4호
• /
• pp.5-13
• /
• 2008

충전물이 암 절리면의 전단강도를 감소시키는 것과 유사하게 콘크리트와 주변 암반근입부 사이의 연약한 물질은 암반에 근입된 현장타설말뚝의 주면저항력을 감소시킨다. 이러한 현상은 콘크리트 타설 후에 암반 근입부 측벽에서 천공잔류물이나 스미어 또는 재성형 암반을 생성시키는 시공과정에서도 형성되게 된다. 콘크리트 말뚝과 주변 암반 사이의 접촉면의 특성은 시공법에 따라서 크게 영향을 받는다. 콘크리트 타설과정 또는 그 이후 형성되는 연약한 물질이 존재하거나 거칠기와 같은 콘크리트-암 접촉면의 특성은 말뚝의 주면부 거동에 큰 영향을 미친다. 본 연구에서는 유한차분법 코드를 기반으로 하는 FLAC 2D를 이용하여 스미어현상이 발생한 암반에 근입된 현장타설말뚝의 거동특성을 조사하기 위하여 변수분석을 실시하였다. 본 연구의 결과로서, 정적연직하중을 받는 암반에 근입된 현장타설말뚝의 극한주면저항력에 영향을 미치는 요소와 말뚝두부의 침하에 영향을 미치는 요소들을 확인할 수 있었다.

• Computers and Concrete
• /
• 제10권1호
• /
• pp.1-18
• /
• 2012

This paper presents the details of studies conducted on hollow concrete block masonry (HCBM) units and wall panels. This study includes, compressive strength of unit block, ungrouted and grouted HCB prisms, flexural strength evaluation, testing of HCBM panels with and without opening. Non-linear finite element (FE) analysis of HCBM panels with and without opening has been carried out by simulating the actual test conditions. Constant vertical load is applied on the top of the wall panel and then lateral load is applied in incremental manner. The in-plane deformation is recorded under each incremental lateral load. Displacement ductility factors and response reduction factors have been evaluated based on experimental results. From the study, it is observed that fully grouted and partially reinforced HCBM panel without opening performed well compared to other types of wall panels in lateral load resistance and displacement ductility. In all the wall panels, shear cracks originated at loading point and moved towards the compression toe of the wall. The force reduction factor of a wall panel with opening is much less when compared with fully reinforced wall panel with no opening. The displacement values obtained by non-linear FE analysis are found to be in good agreement with the corresponding experimental values. The influence of mortar joint has been included in the stress-strain behaviour as a monolith with HCBM and not considered separately. The derived response reduction factors will be useful for the design of reinforced HCBM wall panels subjected to lateral forces generated due to earthquakes.

• 한국방재학회 논문집
• /
• 제11권2호
• /
• pp.67-73
• /
• 2011

본 연구의 목적은 공기 단축과 초기 공사비를 절감하기 위해 PC 긴장재를 사용하지 않고, 슬리브와 일반 철근만으로 구성된 경제적이면서 시공성이 우수한 프리캐스트 교각 공법 개발에 있다. 이를 위해 본 연구에서는 신형식 철근이음 장치인 그라우팅형(形) 슬리브(Splice sleeve, 이하 슬리브)를 제안하고 최적의 슬리브를 개발하기 위하여 슬리브 길이, 철근직경, 양생방법 등을 변수로 하여 유한요소해석 및 인장실험을 수행하였다. 슬리브의 유한요소해석을 통하여 최적의 형상을 도출하였으며, 인장 성능 검토 결과, 철근의 인발에 의한 파괴는 발생하지 않았으며, 철근의 인장 파괴 혹은 슬리브의 기계적 결함에 의한 볼트 파단만이 관찰되었다. 제안된 슬리브는 우수한 인장성능을 갖고 있음을 확인하였으며 프리캐스트 교각에 무리 없이 적용할 수 있음을 검증하였다.

• 터널과지하공간
• /
• 제31권1호
• /
• pp.66-81
• /
• 2021

본 연구는 삼차원 절리텐서 파라미터와 DFN(discrete fracture network) 블록의 변형특성 간의 상관성 분석을 수행하여 절리텐서의 방향성분 및 일차불변량이 절리성 암반의 변형계수 및 전단탄성계수에 미치는 영향을 평가하였다. 확정적 방향성을 갖는 1~2개의 절리군을 사용하여 절리의 빈도 및 길이분포의 변화에 따라 생성한 총 224개의 DFN 블록에 대하여 절리텐서 파라미터가 산정되었다. 또한, 정육면체 DFN 블록에 대하여 개별요소법을 활용하여 서로 직교하는 세 방향으로 변형특성이 추정되었다. 절리텐서의 일차불변량이 증가할수록 변형계수 및 전단탄성계수는 대체로 저감되는 양상을 나타내지만, 감소폭이 줄어들어 일차불변량이 특정 기준값을 상회하면 변형계수 및 전단탄성계수는 거의 일정한 값을 유지하였다. 삼차원 DFN 블록에 대한 지향적 변형특성은 대응하는 방향의 절리텐서성분과 멱함수의 강한 상관관계를 도출하였다.

• Computers and Concrete
• /
• 제27권5호
• /
• pp.457-472
• /
• 2021

Reinforced concrete (RC) buildings in Taiwan have suffered failure from strong earthquakes, which was magnified by the non-ductile detailing frames. Inadequate reinforcement as a consequence of the design philosophy prior to the introduction of current standards resulted in severe damage in the column and beam-column joint (BCJ). This study establishes a finite element analysis (FEA) of the non-ductile detailing RC column, BCJ, and three-story building that was previously tested through a tri-axial shaking table test. The results were then validated to laboratory specimens having the exact same dimensions and properties. FEA simulation integrates the concrete damage plasticity model and the elastic-perfectly plastic model for steel. The load-displacement responses of the column and BCJ specimens obtained from FEA were in a reasonable agreement with the experimental curves. The resulting initial stiffness and maximum base shear were found to be a close approximation to the experimental results. Also, the findings of a dynamic analysis of the three-story building showed that the time-history data of acceleration and displacement correlated well with the shaking table test results. This indicates the FEA implementation can be effectively used to predict the RC frame performance and failure mode under seismic loads.

• 마이크로전자및패키징학회지
• /
• 제28권2호
• /
• pp.95-103
• /
• 2021

대표적인 저온솔더인 Sn-58Bi에 Ru nanoparticles을 첨가하여 Sn-58Bi-xRu 복합솔더를 제작하고 Cu/OSP 및 ENIG 표면처리된 PCB 기판과 반응시켜 계면반응 및 솔더조인트 신뢰성을 분석하였다. Cu/OSP와의 반응에서 형성된 Cu₆Sn₅ IMC는 Ru 함량에 따른 두께 변화가 거의 없고 100hr aging 후에도 큰 변화없이 고속 전단시험시 솔더 내부로 연성파괴가 발생하였다. ENIG 와의 반응시에는 Ru 함량이 증가함에 따라서 Ni₃Sn₄ IMC 두께가 감소하는 경향을 보였으며 일부 시편에서 ENIG 특유의 취성파괴 현상이 발견되었다. Ru 원소는 계면 부근에서 발견되지 않아서 계면반응에 크게 관여하지 않는 것으로 판단되며 주로 Bi phase와 함께 존재하는 것으로 분석되고 있는데 어떠한 형태로 두 원소가 공존하고 있는지에 대해서는 추가적인 연구가 필요하다.

• Animal Bioscience
• /
• 제35권5호
• /
• pp.677-689
• /
• 2022

Objective: This study was conducted to evaluate the effects of concentrate level and chromium-methionine (Cr-Met) supplementation on the growth performance, carcass characteristics, meat quality, and fatty acid composition of Tan lambs. Methods: Sixty male Tan lambs (21±1.23 kg body weight) fed a finishing diet (concentrate-to-forage ratio: 35:65 [LC group] or 55:45 [HC group]) with daily Cr-Met supplementation (0, 0.75, or 1.50 g) were used in a completely randomized design with a 2×3 factorial arrangement of treatments. Results: Lambs from the HC group had higher average daily gain, dry matter (DM) digestibility, dressing percentages, leg proportions, intramuscular fat (IMF) contents, and saturated fatty acid levels, but lower feed conversion ratios, globulin (GLB) and total protein (TP) concentrations, shear force, and monounsaturated fatty acid (MUFA) levels (all p<0.05). Cr-Met supplementation increased the DM digestibility, GLB and TP concentrations, rack and loin percentages, and cooking loss, but decreased the IMF contents and leg proportions (all p<0.05). Cr-Met supplementation at 0.75 g/d increased the conjugated linoleic acid (CLA) content in both the HC and LC groups (p<0.01). Significant interactions between the concentrate level and Cr-Met dosage were observed for MUFA (p<0.01) and polyunsaturated fatty acid (PUFA) (p<0.01) levels. Meat from the lambs fed an unsupplemented LC diet presented the highest PUFA and MUFA levels (p<0.01). However, the MUFA and PUFA levels decreased significantly with increasing Cr-Met supplementation levels in the LC group (p<0.01), whereas the opposite trend was seen in the HC group. Conclusion: The HC diet improved the growth performance of Tan lambs, increased their profitability by increasing leg and rack joint proportions, and improved meat quality by promoting an IMF content that was more visibly acceptable to consumers. Cr-Met supplementation at 0.75 g/d in a HC diet was the best choice and may be economically beneficial.

• Earthquakes and Structures
• /
• 제24권6호
• /
• pp.439-453
• /
• 2023

Older brick masonry structures generally suffer from low strength defects. Using a cement mortar layer (CML) or steel-meshed cement mortar layer (S-CML) to reinforce existing low-strength brick masonry structures (LBMs) is still an effective means of increasing seismic performance. However, performance indices such as lateral displacement ratios and skeleton curves for LBMs reinforced with CML or S-CML need to be clarified in performance-based seismic design and evaluation. Therefore, research into the failure mechanisms and seismic performance of LBMs reinforced with CML or S-CML is imperative. In this study, thirty low-strength brick walls (LBWs) with different cross-sectional areas, bonding mortar types, vertical loads, and CML/S-CML thicknesses were constructed. The failure modes, load-carrying capacities, energy dissipation capacity and lateral drift ratio limits in different limits states were acquired via quasi-static tests. The results show that 1) the primary failure modes of UBWs and RBWs are "diagonal shear failure" and "sliding failure through joints." 2) The acceptable drift ratios of Immediate Occupancy (IO), Life Safety (LS), and Collapse Prevention (CP) for UBWs can be 0.04%, 0.08%, and 0.3%, respectively. For 20-RBWs, the acceptable drift ratios of IO, LS, and CP for 20-RBWs can be 0.037%, 0.09%, and 0.41%, respectively. Moreover, the acceptable drift ratios of IO, LS, and CP for 40-RBWs can be 0.048%, 0.09%, and 0.53%, respectively. 3) Reinforcing low-strength brick walls with CML/S-CML can improve brick walls' bearing capacity, deformation, and energy dissipation capacity. Using CML/S-CML reinforcement to improve the seismic performance of old masonry houses is a feasible and practical choice.