• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.3
• /
• pp.362-366
• /
• 2008

This study was carried to investigate effects of gamma irradiation on the moisture, crude protein, crude lipid, 2-thiobarbituric acid (TBA) values, color stability, texture, and sensory properties of restructured pork jerky. Restructured pork jerky was irradiated at dose levels of 0, 3, 5, 7 and 10 kGy with a use Co-60 source. There were no significant differences in the moisture, crude protein, crude lipid contents, and TBA values. However, as doses of gamma irradiation increased, the redness (a-value) of restructure pork jerky increased whereas shear force of restructure pork jerky was decreased by gamma irradiation. Sensory evaluation showed that sensory scores were reduced by gamma irradiation. Therefore, gamma irradiation could be an effective means to improve color and texture of restructured pork jerky, but only with proper consideration for sensory quality.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.187-196
• /
• 2005

Since the allowable bearing capacities of piles in weathered/fractured rock are mainly governed by settlement, the load-displacement behavior of pile should be known accurately. To predict pile head settlement at the design stage, the exact understanding of the load-transfer mechanisms is essential. Therefore, in this research, the load-transfer mechanism of drilled shaft socketed into weathered rock was investigated. For the investigation, five cast-in-place concrete piles with diameters of 1,000 mm were socketed into weathered gneiss. The static axial load tests and the load-transfer measurements were performed to examine the axial resistant behavior of the piles. A comprehensive field/laboratory testing program on weathered rock at the Held test sites was also performed to describe the in situ rock mass conditions quantitatively. And then, the effect of rock mass condition on the load transfer mechanism was investigated. The f-w (side shear resistance-displacement) curve of the pile in moderately weathered rock reached to yielding point at a for millimeter displacements, and after yielding point, the rate of resistance increment dramatically decreased. However, the f-w curve in the highly/completely weathered rock did not show the obvious yielding point, and the resistance gradually increased showing the hyperbolic pattern until relatively high displacement (>15 mm). The q-w (end bearing resistance-displacement) curves showed linear response at least until the base displacement of approximately 10 mm, regardless of rock mass conditions.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.11
• /
• pp.5-19
• /
• 2016

This paper presents the results from three-dimensional finite element (FE) analysis undertaken to provide insight into the lateral behaviors of piled gravity base foundation (GBF) for offshore wind turbine. The piled GBF was originally developed to support the gravity based foundation in very soft clay soil. A GBF is supported by five piles in a cross arrangement to achieve additional vertical bearing capacity. This study considered four different cases including a) single pile, b) three-by-three group pile (with nine piles), c) cross-arrangement group pile (with five piles), and d) piled GBF. All the cases were installed in homogenous soft clay soil with undrained shear strength of 20 kPa. From the numerical results, p-y curves and thus P-multiplier was back-calculated. For the group pile cases, the group effect decreased with increasing the number of piles. Interestingly, for the piled GBF, the P-multipliers showed a unique trend, compared to the group pile cases. This study concluded that the global lateral behaviour of the piled GBF was influenced strongly by the interaction between GBF and contacted soil surface.

• BMB Reports
• /
• v.41 no.12
• /
• pp.846-851
• /
• 2008

This study was conducted to identify marbling-related candidate genes in M. longissimus dorsi of high- and low-marbled Hanwoo. The longissimus dorsi muscles were selected for gene expression from eight Hanwoo steer carcasses based on crude fat content. In the analysis of variance, gene expression of five candidate genes, FABP4, SCD, $PPAR\gamma$, Titin and Nebulin was determined to be significantly different between high- and low-marbled Hanwoo steers (P < 0.0001). The Pik-4 and CaMK II genes were also shown to have a significant effect on crude fat content (P < 0.01). In the analysis of the differential expression between high- and low marbled groups, FABP4 gene expression was approximately 2 times higher in the high marbled group relative to the low marbled group. However, the $PPAR\gamma$ and SCD gene were highly expressed in the low marbled group. In addition, Titin and Nebulin were highly expressed in the low marbled group when placed under relatively high shear force. Finally, the Pik-4 and CaM K II gene also displayed a high expression pattern in the low marbled group.

• Journal of Adhesion and Interface
• /
• v.7 no.2
• /
• pp.1-11
• /
• 2006

Interfacial evaluation of the untreated and treated Jute and Hemp fibers reinforced different matrix polypropylene-maleic anhydride polypropylene copolymer (PP-MAPP) composites were investigated by micromechanical technique and dynamic contact angle measurement. For the statistical tensile strength of Jute and Hemp fibers, bimodal Weibull distribution was fitted better than the unimodal distribution. The acid-base parameter on the interfacial shear strength (IFSS) of the natural fiber composites was characterized by calculating the work adhesion, $W_a$. The effect of alkaline, silane coupling agent on natural fibers were obtained with changing MAPP content in PP-MAPP matrices. Alkaline treated fibers made the surface energy to be higher due to removing the weak boundary layers and thus increasing surface area, whereas surface energy of silane treated Jute and Hemp fibers decreased due to blocked high energy sites. MAPP in the PP-MAPP matrix caused the surface energy to increase due to introduced acid-base sites. Microfailure modes of two natural fiber composites were observed clearly differently due to different tensile strength of natural fibers.

• Journal of Adhesion and Interface
• /
• v.13 no.1
• /
• pp.45-50
• /
• 2012

Recently developed polyketone fiber has various applications in the mechanical rubber goods as reinforcement because of its good mechanical properties. However, its surface is not suitable for good adhesion with the rubber matrix. Thus, a surface modification is essential to obtain the good interfacial adhesion. Plasma treatment, in this study, has been conducted to modify the surface of the polyketone fiber. The morphological changes of the fibers by oxygen plasma treatment were observed by using SEM and AFM. The chemical composition changes of PK fiber surface treated with oxygen plasma were investigated using an XPS (X-ray photoelectron spectroscopy). Finally, the effect of these changes on the interfacial adhesion between fiber and rubber was analyzed by using a microdroplet debonding test. By the plasma treatment, oxygen moieties on the fiber surface increased with processing time and power. The surface RMS roughness increases until the proper processing condition, but a long plasma processing time resulted in a rather reduced roughness because of surface degradation. When the treatment time and power were 60 s and 80 W, respectively, the highest interfacial shear strength (IFSS) was obtained between the PK fiber and natural rubber. However, as the treatment time and power were higher than 60 s and 80 W, respectively, the IFSS decreased because of degradation of the PK fiber surface by severe plasma treatment.

• Journal of Life Science
• /
• v.16 no.7 s.80
• /
• pp.1164-1168
• /
• 2006

This study was carried out to investigate the possible for utilization of garbage in pig feed by investigating the functional characteristics of pork from pigs fed dried citrus byproduct. The samples consisted of the pork loin from pigs not fed with dried citrus pulp (DCP-0) and fed with 6% and 10% dried citrus pulp during growing and fattening period (DCP-1) there is no respective comparison here The pH, VBN content, TBARS value, bacterial counts, surface color, water holding capacity, loss degree and rheological properties of the samples were determined by physicochemical properties, and the sensory scores were evaluated. The pH, VBN content, surface color, water holding capacity and loss degree were not different between the samples, but the TBARS value and bacterial counts of DCP-1 were significantly lower than those of the DCP-0 (p<0.05). The cohesiveness, gumminess, chewiness, shear forte value, taste, flavor, tenderness, juiciness and palatability were not different between the samples, but the hardness of DCP-0 was higher than that of the DCP-1 and the springiness of DCP-1 was higher than that of the DCP-0 (p<0.05).

• Journal of the Korean Geotechnical Society
• /
• v.28 no.12
• /
• pp.77-86
• /
• 2012

We have carried out a series of numerical experiments to study the effect of average particle size on the mechanical properties of granite-derived weathered soils. A distinct-element method was adopted to study the changes in macro-scale mechanical properties with particle size and maximum-to-minimum particle size ratio. The numerical soil specimen with cohesion values of 0.25 MPa and internal friction angle of 29 degrees was prepared for reference. While keeping the porosity values constant, we varied particle size and size distribution to study how cohesion and internal friction angle changes. The experimental results show that the values of cohesion apparently decrease with increasing particle size. Changes in the values of internal friction angles are small, but there is a trend of increase in internal friction angle as the average particle size increases. This study demonstrates a possibility that the results of numerical experiments of this type may be used for rapid estimation of mechanical properties of granite-derived weathered soils. For example, when mechanical properties obtained through in situ tests and particle size data obtained through lab analysis are available for a site, it is expected that the mechanical properties of weathered granite soils with varying degrees of weathering (thus, varying particle size) may be estimated rapidly only with particle size data for that site.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.9
• /
• pp.51-62
• /
• 2016

Parametric studies for various site conditions by using 3d numerical model were carried out in order to estimate dynamic behavior of soil-pile-structure system in dry soil deposits. Proposed model was analyzed in time domain using FLAC3D which is commercial finite difference code to properly simulate nonlinear response of soil under strong earthquake. Mohr-Coulomb criterion was adopted as soil constitutive model. Soil nonlinearity was considered by adopting the hysteretic damping model, and an interface model which can simulate separation and slip between soil and pile was adopted. Simplified continuum modeling was used as boundary condition to reduce analysis time. Also, initial shear modulus and yield depth were appropriately determined for accurate simulation of system's nonlinear behavior. Parametric study was performed by varying weight of superstructure, pile length, pile head fixity, soil relative density with proposed numerical model. From the results of parametric study, it is identified that inertial force induced by superstructure is dominant on dynamic behavior of soil-pile-structure system and effect of kinematic force induced by soil movement was relatively small. Difference in dynamic behavior according to the pile length and pile head fixity was also numerically investigated.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.3
• /
• pp.15-23
• /
• 2020

Ground motion models predicting intensity measures on surface use a time-averaged shear wave velocity, V_S30, as a key variable simulating site effect. The V_S30 can be directly estimated from V_S profiles if the profile depth (z) is greater than or equal to 30 m. However, some sites have V_S profiles with z < 30 m. In this case V_S30 can be predicted using extension models. This study proposes new coefficient sets for existing prediction equations using 297 Korea V_S profiles. We have collected V_S profiles from KMA and Geoinfo database. Fitting six existing methods to data, we suggest new coefficients for each method and evaluate their performance. It turns out that if z ≥ 15 m, the standard deviation (σ) of residual in log₁₀ is 0.061, which indicates that the estimated V_S30 is nearly accurate. If z < 15 m, the σ keeps increasing up to 0.1 for z = 5 m, so we caution the use of models at very low z. Nonetheless, we recommend investigating up to 30 m depth for V_S30 calculation if possible.