• 한국광물학회지
• /
• 제9권1호
• /
• pp.1-6
• /
• 1996

Woolastonite from Susan occurs as intercalations in limestone beds of Lower Paleozoic Joseon Supergroup. It is a thermal metamorphic product of impure limestone. Electron microprobe analysis shows that it is considerably pure wollastonite. It has triclinic cell with a=7.932$\AA$, b=7.328$\AA$, c=7.069$\AA$, $\alpha$=89.995$^{\circ}$, $\beta$=$95.255^{\circ}$, and $ \Upsilon=103.367^{\circ}$.Dissolution behaviors of wollastonite have been studied conducting three different dissolution experiments; two different reactions with HC1 (one batch and one re-initialization experiment) and one traction with distilled water. In the batch type powder wollastonite-HCl reaction, pH of solution rapidly increases in the early stage and then its rate of increase slows down to reach plateau resulting in parabolic relationship with time. It is represented by the early rapid rise and fall in pH giving a sharp pH-edge and succeeding slow rise in the re-initialization experiment. The early rapid rise in pH is due to the rapid sorption of H- in solution to oxygens on the reactive surface of wollastonite and the fall in pH means that all reactive surface sites are occupied by H- ions and no more H- adsorption occurs. The slow rise in pH following the pH- edge is due to the dissolution of wollastonite as evidenced by the correlation of pH variation and cation concentration. Dissolution of powder wollastonite in HCl shows linear trend with time. Si is dissolved predominantly over Ca at a constant rate. Ca is dissolved predominantly in the very early stage. Dissolution rate of coarse-grained wollastonite fragments in distilled water is parabolic with times howing a rapid reaction in the early stage and a slow reaction in the advanced stage. The Ca/Si ratio in solution is high in the case of coarse-grained wollastonite fragment as compared with powder wollastonite. The coarse-grained wollastonite fragment-water (acid) reaction resulted in the solution with an elevated constant pH value (alkaline) giving an important significance on the environmental view point.

• 대한디지털의료영상학회논문지
• /
• 제12권2호
• /
• pp.127-132
• /
• 2010

In this study, the correlation among the changes of Modulation Transfer Function(MTF) in the noise and high-contrast resolution and the change of Contrast to noise ratio(CNR) in the low-contrast resolution will be examined to investigate the estimation of image quality according to the type of algorithms. The image data obtained by scanning American Association of Physicists in Medicine(AAPM) phantom was applied to each algorithm and the exposure condition of 120 kVp, 250 mAs, and then the CT number and noise were measured. The MTF curved line of the high-contrast resolution was calculated with Point Spread Function(PSF) by using the analysis program by Philips, resulting in 0.5 MTF, 0.1 MTF and 0.02 MTF respectively. The low-contrast resolution was calculated with CNR and the uniformity was measured to each algorithm. Since the measurement value for the uniformity of the equipment was below ${\pm}$ 5 HU, which is the criterion figure, it was found to belong to the normal range. As the algorithm got closer from soft to edge, the standard deviation of CT number increased, which indicates that the noise increased as well. As for MTF, 0.5 MTF, 0.1 MTF and 0.02 MTF were all sharp algorithms, and as the algorithm got closer from soft to edge, it was possible to distinguish more clearly with the naked eye. On the other hand, CNR gradually decreased, because the difference between the contrast hole CT number and the acrylic CT number was the same while the noise of hole increased.

• 전자공학회논문지S
• /
• 제36S권7호
• /
• pp.81-89
• /
• 1999

통신에 의한 전송 영상은 잡음이나 번짐 또는 일그러짐 등을 항상 포함한다. 본 논문에서는 적응형 일반스텍 최적화 필터(OAGSF: optimal adaptive generalized stack filter)라는 영상복원 공간 필터를 제안하였는데, 이는 영상의 복원에서 잡음 제거율과 외곽선 정보의 보존률의 증가을 위해 신경회로맘의 역전파 학습 알고리즘의 가중치 학습 알고리즘을 기반으로 적응형 일반스택 필터(AGSF)를 최적화 시킨 것이다. 적응형 일반스택 필터는 일반스택 필터(GSF: generalized stack filter)와 적응형 다단계 메디안 필터(AMMF; adaptive multistage median filter)로 구분하고, 일반스텍 필터는 스택 필너치 기능을 보완한것이고, 적응형 다단계 메디안 필터는 메디안 필터의 외곽선 정보 보존률을 높인 것이다. 신경회로망의 역전파 학습 알고리즘에 대하여 두가지 가중치 학습 알고리즘인 최소평균절대 (LMA:Least Mean Absolute) 알고리즘과 최소평균자승(LMS: Least Mean Square) 알고리즘을 이용하여 적응형 일반스택 필터를 최적화하였다. 본 논문에서 제시한 신경회로망을 이용한 영상복원 공간필터에 대해 실험결과를 통해 제시하였다.

• Wind and Structures
• /
• 제34권1호
• /
• pp.43-58
• /
• 2022

The BARC flow is studied via Direct Numerical Simulation at a relatively low turbulent Reynolds number, with focus on the geometrical representation of the leading-edge (LE) corners. The study contributes to further our understanding of the discrepancies between existing numerical and experimental BARC data. In a first part, rounded LE corners with small curvature radii are considered. Results show that a small amount of rounding does not lead to abrupt changes of the mean fields, but that the effects increase with the curvature radius. The shear layer separates from the rounded LE at a lower angle, which reduces the size of the main recirculating region over the cylinder side. In contrast, the longitudinal size of the recirculating region behind the trailing edge (TE) increases, as the TE shear layer is accelerated. The effect of the curvature radii on the turbulent kinetic energy and on its production, dissipation and transport are addressed. The present results should be contrasted with the recent work of Rocchio et al. (2020), who found via implicit Large-Eddy Simulations at larger Reynolds numbers that even a small curvature radius leads to significant changes of the mean flow. In a second part, the LE corners are fully sharp and the exact analytical solution of the Stokes problem in the neighbourhood of the corners is used to locally restore the solution accuracy degraded by the singularity. Changes in the mean flow reveal that the analytical correction leads to streamlines that better follow the corners. The flow separates from the LE with a lower angle, resulting in a slightly smaller recirculating region. The corner-correction approach is valuable in general, and is expected to help developing high-quality numerical simulations at the high Reynolds numbers typical of the experiments with reasonable meshing requirements.

• Geomechanics and Engineering
• /
• 제34권1호
• /
• pp.103-113
• /
• 2023

This study focused on understanding the relationship between the design of a tunnel boring machine disc cutter ring and its rock-breaking efficiency, as well as the applicable conditions of different cutter ring types. The discrete element method was used to establish a numerical model of the rock-breaking process using disc cutters with different ring types to reveal the development of rock damage cracks and variation in cutter penetration load. The calculation results indicate that a sharp-edged (V-shaped) disc cutter penetrates a rock mass to a given depth with the lowest load, resulting in more intermediate cracks and few lateral cracks, which leads to difficulty in crack combination. Furthermore, the poor wear resistance of a conventional V-shaped cutter can lead to an exponential increase in the penetration load after cutter ring wear. In contrast, constant-cross-section (CCS) disc cutters have the highest quantity of crack extensions after penetrating rock, but also require the highest penetration loads. An arch-edged (U-shaped) disc cutter is more moderate than the aforementioned types with sufficient intermediate and lateral crack propagation after cutting into rock under a suitable penetration load. Additionally, we found that the cutter ring wedge angle and edge width heavily influence cutter rock-breaking efficiency and that a disc cutter with a 16 to 22 mm edge width and 20° to 30° wedge angle exhibits high performance. Compared to V-shaped and U-shaped cutters, the CCS cutter is more suitable for soft or medium-strength rocks, where the penetration load is relatively small. Additionally, two typical case studies were selected to verify that replacing a CCS cutter with a U-shaped or optimized V-shaped disc cutter can increase cutting efficiency when encountering hard rocks.

• 지구물리
• /
• 제2권1호
• /
• pp.27-38
• /
• 1999

최근 공개된 위성중력을 이용하는 오차 최소화 기법을 적용하여 선상중력내 존재하는 구간 측선간 오차나 교차점 오차를 성공적으로 보정하였으며, 보정된 선상중력을 위성중력과 결합하여 고해상 중력분포를 도출하였다. 오차 최소화 과정에서 울릉분지의 선상중력은 위성중력보다 장주기 성분에서 상대적으로 크게 보정되었으나 단주기 성분은 그대로 보존되었다. 이것은 선상중력이 갖는 단주기의 중력 성분이 훼손되지 않은 채 안정되고 연속성을 갖는 장주기의 인공위성 중력분포에 잘 접합될 수 있다는 것을 보여 준다. 통합된 후리에어이상도는 위성중력의 장주기 성분과 선상중력의 단주기 성분을 모두 표현하므로 해저지형 및 지질분포의 해석에서 보다 상세하고 신뢰성 있는 정보를 제공한다. 후리에어이상은 수심이 깊은 분지 중앙 지역이 해저산이나 대지 등 높은 지형으로 이루어진 분지 주변부 보다 상대적으로 낮게 분포하는 등 전반적으로 해저지형의 분포 경향에 부합되어 변화한다. 그러나 대륙사면을 이루고 있는 분지의 서쪽 및 동쪽 주변부를 따라서는 지역적으로 함몰된 퇴적기반과 두꺼운 퇴적층 및 대륙 주변부에서 특징적인 가장자리 효과로 인한 저이상대가 발달하고 있다. 울릉도 북동부에 위치한 한국대지 및 울릉대지에서 북동-남서방향의 선형분포를 갖는 중력이상은 동해가 열개되는 동안 균열된 지각 사이를 따라 일어난 화산활동의 결과로 형성된 해산이나 관입암체가 선형으로 배열함으로서 기인한 것으로 해석된다. 선형으로 배열된 고중력분포는 울릉대지 서쪽 경계부에서 급구배를 보이는 북북서-남남동 방향의 직선적인 중력분포에 의해 절단되고 있는 데 이 급구배의 중력이상은 울릉대지 서부 경계를 이루는 단층선애에 기인한다. 울릉대지가 서쪽으로 뚜렷한 단층 접촉을 나타내고 있으나 지형적인 형태에 있어서 대비되지 않는 것은 울릉대지가 단층을 경계로 분리되어 이동되어 왔을 가능성을 시사한다. 분지의 중앙 북동부에서는 수심이 깊어지는 데 비해 중력치는 오히려 높아지는 경향을 나타내고 있는 것은 맨틀이 주변부에 비해서 상대적으로 천부에 존재하고 있는 것이 가장 큰 요인이며, 해저지각의 두께가 얇은 대신 지각의 밀도가 주변 대륙보다 높은 데도 기인한다.

• Wind and Structures
• /
• 제12권4호
• /
• pp.299-312
• /
• 2009

It has long been studied about the flow around bluff bodies, but the effect of aspect ratio on the sharp-edged bodies in thick turbulent boundary layers is still argued. The author investigates the flow characteristics around a series of rectangular bodies ($40^d{\times}80^w{\times}80^h$, $80^d{\times}80^w{\times}80^h$ and $160^d{\times}80^w{\times}80^h$ in mm) placed in a deep turbulent boundary layer. The study is aiming to identify the extant Reynolds number independence of the rectangular bodies and furthermore understand the surface pressure distribution around the bodies such as the suction pressure in the leading edge, when the shape of bodies is changed, responsible for producing extreme suction pressures around the bluff bodies. The experiments are carried out at three different Reynolds numbers, based on the velocity U at the body height h, of 24,000, 46,000 and 67,000, and large enough that the mean boundary layer flow is effectively Reynolds number independent. The experiment includes wind tunnel work with the velocity and surface pressure measurements. The results show that the generation of the deep turbulent boundary layer in the wind tunnel and the surface pressure around the bodies were all independent of Reynolds number and the longitudinal length, but highly dependent of the transverse width.

• 한국안광학회지
• /
• 제14권2호
• /
• pp.27-30
• /
• 2009

목적: 현재 판매되어지고 있는 SCL의 건조 및 젖음 상태에 따라 UV 및 가시광선 투과율을 측정하였다. 방법: 시중에 유통 중인 5가지 종류의 재료를 건조 및 젖음 상태에 따라 Spectrophotometer로 측정하여, SCL의 광학적 특성을 조사하였다. 결과: 5가지 재료 중에서 젖음 및 건조 상태의 구별없이 일정한 투과값을 가진 재료도 있었다. 측정된 SCL의 가시광선 범위 투과율은 약 80% 이상의 투과율이 나와 광학적으로 우수하였다. 또한 대다수 SCL의 경우 UV에서 젖음 상태의 투과율이 건조 상태보다 높은 투과율을 나타냈다. 결론: 측정된 SCL의 재료 중에는 가시광선 범위에서 우수한 광학적 성능을 보였지만 대다수 SCL의 경우 UV 범위에서 높은 투과율이 나타냈다. 그러므로 앞으로 UV를 차단 기능이 있는 신소재 개발의 필요성이 강조될 것이다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제9권3호
• /
• pp.1121-1139
• /
• 2015

In texture-plus-depth format, depth map compression is an important task. Different from normal texture images, depth maps have less texture information, while contain many homogeneous regions separated by sharp edges. This feature will be employed to form an efficient depth map coding scheme in this paper. Firstly, the histogram of the depth map will be analyzed to find an appropriate threshold that segments the depth map into the foreground and background regions, allowing the edge between these two kinds of regions to be obtained. Secondly, the two regions will be encoded through rate distortion optimization with a shape adaptive wavelet transform, while the edges are lossless encoded with JBIG2. Finally, a depth-updating algorithm based on the threshold and the depth range is applied to enhance the quality of the decoded depth maps. Experimental results demonstrate the effective performance on both the depth map quality and the synthesized view quality.

• 대한조선학회논문집
• /
• 제43권5호
• /
• pp.538-549
• /
• 2006

A code is developed to simulate a viscous flow field around a deformable body using the hybrid Cartesian/immersed boundary method. In this method, the immersed boundary(IB) nodes are defined near the body boundary then velocities at the IB nodes are reconstructed based on the interpolation along the normal direction to the body surface. A new method is suggested to define the IB nodes so that a closed fluid domain is guaranteed by a set of IB nodes and the method is applicable to a zero-thickness body such as a sail. To validate the developed code, the vorticity fields are compared with other recent calculations where a cylinder orbits and moves into its own wake. It is shown the code can handle a sharp trailing edge at Reynolds number of $10^5$ under moderate requirements on girds. Finally the developed code is applied to simulate the vortex shedding behind a deforming foil with flapping tail like a fish. It is shown that the acceleration of fluids near the flapping tail contributes to the generation of the thrust for propulsion.