• Fashion & Textile Research Journal
• /
• v.24 no.6
• /
• pp.812-824
• /
• 2022

This study proposes to develop a 3D printed re-entrant(RE) strip by shape memory thermoplastic polyurethane that can be deformed and recovered by thermal stimulation. The most suitable 3D printing infill density condition and temperature condition during shape recovery for mechanical behavior were confirmed. As the poisson's ratio indicated, the higher the recovery temperature, the closer the poisson's ratio to zero and the better the auxetic properties. After recovery testing for five minutes, it appeared that the shape recovery ratio was the highest at 70℃. The temperature range when the shape recovery ratio appeared to be more than 90% was a recovery temperature of more than 50℃ and 60℃ when deformed under a constant load of 100 gf and 300 gf, respectively. This indicated that further deformation occurred after maximum recovery when recovered at a temperature of 80℃, which is above the glass transition temperature range. As for REstrip by infill density, a shape recovery properties of 100% was superior than 50%. Additionally, as the re-entrant structure exhibited a shape recovery ratio of more than 90%, and exhibited auxetic properties. It was confirmed that the infill density condition of 100% and the temperature condition of 70℃ are suitable for REstrips for applying the actuator.

• Transactions of Materials Processing
• /
• v.19 no.2
• /
• pp.132-137
• /
• 2010

In the multi-pass shape drawing process, the appropriate process design is very important to produce sound products. The reduction ratio, die angle, and the intermediate die shape are very important process variable of the multi-pass shape drawing. The aim of this study is the determination of the reduction ratio, die angle, and the intermediate die shape of the 2 pass shape drawing process for producing steering spline shaft. In this study, FE analysis, Taguchi method, and ANN(artificial neural network) were applied to determine the appropriate reduction ratio, die angle, and intermediate die shape. After the determination of the process variables, FE analysis and drawing experiment were performed to evaluate the effectiveness of the determined process variables. The dimensional accuracy of the final drawn spline shaft was evaluated by using 3D surface profiler and 3D laser digitizing system.

• Journal of the Korea Concrete Institute
• /
• v.12 no.4
• /
• pp.103-111
• /
• 2000

The influence of the improvement of grain shape of the coarse aggregate to the unit powder content of concrete and the fine aggregate ratio for the increase of the flowability and segregation resistance of high performance concrete was examined. According to the experimental results, flowability and compacting of concrete presents best states in the S/a which has the smallest 패야 ratio. The coarse aggregate after improvement of grain shape, that has changed from the 0.68 of spherical rate of disk shape to 0.73, led fine aggregate ratio to be down 6% (i.e from 47% to 41%). The improvement of grain shape of the coarse aggregate also led the lowest unit powder content to be down 60kg/㎥ (ie from 530kg/㎥ to 470kg/㎥). And approximate 10% of unit water content has been reduced as unit powder content was down. However, the compressive strength after the improvement of grain shape of the coarse aggregate decreased to 5% due to decrease of adhesiveness of the aggregate and cement paste.

• Transactions of Materials Processing
• /
• v.18 no.7
• /
• pp.550-555
• /
• 2009

In the multi-pass shape drawing process, the pass schedule that includes the determination of reduction ratio and intermediate die shape is very important. This study used the equal reduction, equal load, and electric field analysis method for pass schedule of the multi-pass shape drawing. The reduction ratio was calculated by the equal reduction and equal load method. And the intermediate die shape was determined by the result of the electric field analysis and the calculated reduction ratio. The proposed pass schedule method was applied to a shape drawing for producing cross roller guide. Finally, FE-analysis and shape drawing experiment were performed to verify the effectiveness of the proposed method.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.302-305
• /
• 2005

In this study, settlement characteristics of 38 CFRD was investigated from monitoring data and the method to estimate the dam settlements considering valley shape during constructions was proposed. The construction modulus of dam was found to be dependent on void ratios and valley shape factor. The construction modulus varied with valley shape and decreased with increasing void ratio. Also, the modulus was increased when the shape coefficient was less than 4. The settlement investigation results showed that the total settlement was proportional to the value of the settlement coefficient multiplied by the shape coefficient divided by void ratio.

• Fashion & Textile Research Journal
• /
• v.12 no.2
• /
• pp.214-218
• /
• 2010

This research was to judge on the gathered skirt's shape by visual images that was from the different gathered skirts according to different sewing conditions; fabrics(cotton, mixed-wool, polyester), ratio of gathers(1.5T, 2.0T, 2.5T). Questionnaire consists of 33 semantic differential scale expressing gathered skirt's image, and 10 items of the shape were measured by 3D measurements method. The data were analyzes by factor analysis, correlation analysis, ANOVA. The image of gathered skirts was composed of the five factors of activities, attraction, grace, softness, and ordinary and it was showed that these five factors occupied 68.4% of the total variance. The shape of gathered skirts was composed of the two factors of the side and the front, and it was showed that these two factors occupied 93.6% of the total variance. According to correlation analysis of visual shape, the front was significant in activities, attraction and ordinary, and the side was significant in activities, grace and ordinary. As a result of ANOVA, the visual images were significant in ratio of gathers. 2.5 ratio of gathered skirts were perceived to be more active and attractive, and 1.5 ratio of gathered skirts were more ordinary and graceful.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.127-130
• /
• 2015

The objective of this study is to investigate the real flame shape and characteristic of annular combustor. To identify the effects of combustor length ratio and equivalence ratio on the flame shape in annular combustion configuration, the employed parameters are combustor length ratio 0.6-1.0, equivalence ratio 0.7-1.1. The flame shape is visualized using DSLR camera and precision optic mirror. The flame intensity is analyzed by $OH^{*}$ chemiluminescence images with ICCD camera. CO and NOx emission performance is also examined using an exhaust gas analyzer. From the visualized images, it is confirmed that the different tendency appeared in combustor length ratio 0.6-0.7 and 0.8-1.0. The results of $OH^{*}$ chemiluminescence show that the flame intensity is the most uniform for equivalence ratio 0.9. The smaller equivalence ratio is, the less emission of CO and NOx will be in this investigation range.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.21.2-274
• /
• 1999

This study aims to examine the influence of the unit powder content of concrete and the fine aggregate ration of high flowing concrete after the improvement of grain shape of the coarse aggregate. According to the experimental results, flowbility and compating of concrete presents the best states in the S/a which has the smallest void ratio. The coarse aggregate after improvement of grain shape has been changed from 0.68 circular ratio of disc shape to 0.73 circular shape. It lead to be down 6% of fine aggregate ratio (from 47% to 41%), which is satisfactory to compacting. Also, the improvement of grain shape of the coarse aggregate lead the lowest unit powder content to be down 60kg/㎥ from (530kg/㎥ to 470kg/㎥). And about 11% unit water content can be reduced as unit powder conent is down.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.369-372
• /
• 2000

ESO(Evolutionary Structural Optimization) method is known that elements involved low stress value are removed from the previous model or that elements are added around elements involved high stress level on it and then the optimized model is obtained with required weight. Rejection ratio/addition ratio and evolutionary ratio are predefined and elements having lower/higher stress than reference stress, which average Mises stress on edge elements times rejection ratio, are deleted/added. In this study, when the plate having a cutout is subjected various in-plane load, a cutout shape is optimized using ESO method. ANSYS is used to analyse a finite element model and optimization procedure is made by APDL (ANSYS Parametric Design Language). ESO method is useful in rather than a complex structure optimization as well as a cutout shape optimization.

• Computers and Concrete
• /
• v.23 no.5
• /
• pp.335-349
• /
• 2019

A low-cycle loading experiment of 16 transfer column specimens was conducted to study the influence of parameters, likes the extension length of shape steel, the ratio of shape steel, the axial compression ratio and the volumetric ratio of stirrups, on the shear distribution between steel and concrete, the concrete damage state and the degradation of lateral stiffness. Shear force of shape steel reacted at the core area of concrete section and led to tension effect which accelerated the damage of concrete. At the same time, the damage of concrete diminished its shear capacity and resulted in the shear enlargement of shape steel. The interplay between concrete damage and shear force of shape steel ultimately made for the failures of transfer columns. With the increase of extension length, the lateral stiffness first increases and then decreases, but the stiffness degradation gets faster; With the increase of steel ratio, the lateral stiffness remains the same, but the degradation gets faster; With the increase of the axial compression ratio, the lateral stiffness increases, and the degradation is more significant. Using more stirrups can effectively restrain the development of cracks and increase the lateral stiffness at the yielding point. Also, a formula for calculating the yielding lateral stiffness is obtained by a regression analysis of the test data.