• Fire Science and Engineering
• /
• v.25 no.4
• /
• pp.74-81
• /
• 2011

The numerical analyses for three different shafts in geometry of high buildings were carried out by using computational fluid dynamics model (FDS ver.5.3) for the calculation of the pressure difference and the location of the neutral plane and the visualization of stack effect. At 10 seconds of stack effect, the pressure difference of stack effect in the elevator shaft (79.3 Pa) almost corresponded to the theoretical value (78 Pa). At 300 seconds of stack effect, all the neutral planes of three cases were located about 49 m above floor, where was 5 m higher than the theoretical value. The maximum pressure difference between upper and lower position of shaft decreased with increasing of the geometrical complexity of shaft. This study showed that there was the difference of the stack effects among the geometries of shafts with the visualization of stack effect.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.69-72
• /
• 2008

The so-called Pier-Shafts system which consists of the continuous column and shaft is often used to support the highway bridge structure because of advantages in easy construction and low cost. In the earthquake region, the Pier-Shafts system undergoes large displacements and represents a nonlinear behavior under the lateral seismic loading. The soil-pile interaction should be considered for more accurate analysis of the Pier-Shafts system. In this study, a transverse response of a reinforced concrete Pier-Shafts system inside multi-layered soil medium is predicted using a finite element program which adopts an elasto-plastic interface model for the interface behavior between the shaft and the soil. Then, seismic analysis is performed to evaluate the performance of Pier-Shafts system under strong ground motion and their results are verified with experimental data.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.1
• /
• pp.7-13
• /
• 2021

In recent years, the importance of environmental regulations is increasing in the shipping industry, and the demands of the industry for this are rapidly increasing. Accordingly, the demand of ship owners is increasing as the shaft generator is a technology that responds to environmental regulations that can be applied to ships the fastest. The shaft generator is a device that can increase the fuel consumption rate of the main propulsion engine by installing an electric motor in the main propulsion engine and using it variably according to the load environment. It operates by the power of the motor at low speeds, and when a sudden load is required, the main propulsion engine and motor operate together, enabling efficient operation. In this paper, the diesel engine and shaft generator of a tug boat are modeled using MATLAB Simulink, and the fuel consumption rate is verified through simulation.

• Archives of Reconstructive Microsurgery
• /
• v.8 no.2
• /
• pp.97-107
• /
• 1999

The osteogenic capacity of the vascularized periosteum autograft has been extensively demonstrated by experimental works. The objective of this study was to characterize the behavior of experimental model of vascularized periosteal flap(VPF) by observing sequential stages of osteogenesis after simulated VPF in rabbits. In experimental group, segmental resection of bone including the periosteum was performed in 22 radii of 22 New Zealand white rabbits preserving the periosteal circulation of median artery to the periosteum. In order to simulate the transplantation of VPF, the vascular pedicle consisting of median artery and veins was dissected from adjacent soft tissue and the periosteum was longitudinally incised to remove the bone followed by repair of the periosteum. From the first to sixteenth week after the simulated VPF, the changes in VPFs were observed by radiological, light microscopical, scanning electron microscopical methods and the activity of osteocalcin was measured by immunohistochemical method. In control group, the bone tissue and periosteum were completely removed from the mid-shaft of radius and the findings were observed by radiological and light microscopical methods. From the results of this study, it is demonstrated that the experimental model of VPF is vigorously and uniformly osteogenic. Therefore it is thought that VPF can be used as a measure to treat bone defect of shaft of long bone.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.3
• /
• pp.99-111
• /
• 1999

The frictional capacity of auger-cast piles is often very small because of the disturbance of the soil surrounding the pile during the excavation process. Usage of expansive agents and a pressurized injection technique for auger-cast piles should improve the frictional resistance between pile and soil. This paper presents the test results of auger-cast model piles installed with expansive mortar in laboratory compacted weathered soil. The model piles were installed in a calibration chamber with a variation in the amount of expansive agent, the injection process and the chamber pressure. It was observed that the pile shaft resistance increases with the increased amount of expansive agent, and also increases when mortar is pressure injected. The shaft resistance increased up to 24% for the pile installed only with expansive mortar and increased up to 56% for the pile installed with the pressurized injection of expansive mortar, compared with that of piles with plain mortar.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.118-124
• /
• 2005

An automotive bushing is a device used in automotive suspension systems to reduce the load transmitted from the wheel to the frame of the vehicle. A bushing is a hollow cylinder, which is bonded to a solid steel shaft at its inner surface and a steel sleeve at its outer surface. The relation between the force applied to the shaft and the relative deformation of a bushing is nonlinear and exhibits features of viscoelasticity. In this paper, an automotive bushing is regarded as nonlinear viscoelastic incompressible material. Instron 8801 equipment was used for experimental res earch and ramp-to-constant displacement control test was used for data acquisition. Displacement dependent force relaxation function was obtained from the force extrapolation method and expressed as the explicit combination of time and displacement. Pipkin-Rogers model, which is the direct relation of force and displacement, was obtained and comparison studies between the experimental results and the Pipkin-Rogers results were carried out.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.6
• /
• pp.769-777
• /
• 1999

This paper presents models for the dynamic simulation of a regenerative gas turbine and describes dynamic behaviors of a small regenerative engine. A quasi-steady model is introduced where the inertia of the working fluid is assumed to be negligible compared with the mechanical inertia of the rotating shaft. Based on this quasi-steady model, the transient model for the heat exchanger is employed to simulate the unsteady heat exchange in the recuperator. The effect of the thermal inertia of the recuperator metal on transient behaviors is analyzed by comparing the predicted results of the transient and steady state heat exchanger models. For several load change modes such as sudden increase, decrease and periodic variation, engine dynamic characteristics are investigated by applying a fuel control logic for the constant shaft speed. It is found that the thermal inertia of the recuperator metal has a dominant effect on the whole engine dynamic behavior.

• Tribology and Lubricants
• /
• v.39 no.2
• /
• pp.61-71
• /
• 2023

This study proposes a procedure for designing a labyrinth seal that meets both leakage flow rate and rotordynamic performance criteria (effective damping, amplification factor, separation margin, logarithmic decrement, and vibration amplitude). The seal is modeled using a one control volume (1CV) bulk flow approach to predict the leakage flow rate and rotordynamic coefficients. The rotating shaft is modeled with the finite element (FE) method and is assumed to be supported by two linearized bearings. Geometry, material and operating conditions of the rotating shaft, and the supporting characteristics of the bearings were fixed. A single labyrinth seal is placed at the center of the rotor, and the linearized dynamic coefficients predicted by the seal numerical model are inserted as linear springs and dampers at the seal position. Seal designs that satisfy both leakage and rotordynamic performance are searched by modifying five seal design parameters using the multi-grid method. The five design parameters include pre-swirl ratio, number of teeth, tooth pitch, tooth height and tooth tip width. In total, 12500 seal models are examined and the optimal seal design is selected. Finally, normalization was performed to select the optimal labyrinth seal designs that satisfy the system performance requirements.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.7
• /
• pp.559-564
• /
• 2016

The objectives of this paper are to develop a finite element analysis model to analyze press-fitted and bending load conditions in a press-fitted assembly, and propose a hub shape optimization method to minimize contact pressure near the shaft contact edge. Numerical asymmetric-axisymmetric finite element models have been developed to predict contact stress on press-fitted shafts. The global optimization method, genetic algorithm, local optimization method, and sequential quadratic programming were applied to a press-fitted assembly to optimize the hub contact edge geometry. The results showed that the maximum contact pressure with the optimized hub shape decreased more than 60 % compared to conventional hubs and the maximum contact stress affecting fatigue life was reduced about 47 %. Hub shape optimization can be useful to increase the load capability of press fits in terms of wear and fatigue behavior.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1640-1643
• /
• 2005

This paper presents analysis of dynamic characteristics of a high-speed milling spindle with a drawbar and a built-in motor. The spindle system with a built-in motor can be used to simplify the structure of machine tools, to improve the machining flexibility of machine tools, and to perform the high speed machining. In this system the shaft is usually assumed as a rigid rotor. In this paper, the modal characteristics of drawbar in high-speed milling spindle system due to supporting stiffness between drawbar and shaft and considering the mass and stiffness effects of the built-in motor's rotor are analyzed by numerical method. The result shows enough stiff supports must be provided between shaft and drawbar to prevent occurring drawbar vibration lower than the natural frequency of 1st bending mode of spindle. And considering the mass and stiffness of built-in motor's rotor is important thing to derive more accurate results.