• Journal of Energy Engineering
• /
• v.21 no.2
• /
• pp.168-178
• /
• 2012

The objective of this study is applied to office buildings to evaluate quantitative evaluation method about performance of double-skin at design stage to establish the basis for the purpose of evaluation performance. Select the evaluation building about design plan for applying the double-skin using the dynamic heat load analysis program the annual heating and cooling load of before and after the double-skin. Using CFD to analyze wind factor and applied ventilation for realistic results. Effects of double-skin to apply, and control techniques that can be done more realistically proposed through to set and control for shade control mode of ventilator and inside cavity wall of double-skin. Apply for the building the double-skin due to interpretation of the annual heating and cooling loads applied to interpret the quantitative effect confirmed the possibility. According to the form of a double skin was confirmed cavity environmental changes.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.8 no.3
• /
• pp.135-140
• /
• 1988

This field experiment was carried out to determine the effects of cutting times (3,4 and 5 times $yr^{-1}$) and cutting heights (3, 6 and 9 cm) on the growth and dry matter(DM) yield of grasses grown under pine trees, and botanical composition of woodland pasture. The conditions of the experimental field was south direction with 30% of shade (ca. 70% of full sunlight). Annual DM yield was higher in the plots cut 4 times (6,097 kg) and 3 times (5,953 kg) than in 5 times (5,305 kg $ha^{-1}$). However, it ip considered that total nutrient yields may be not different among 3 treatments. The yield was significantly (P < 0.05) increased with higher cutting height, regardless of cutting time. The 9 cm of stubble height was very effective on both increasing DM production and seasonal distribution of DM. In botanical composition, 3 cm and 6 cm of cutting height accelerated the percentages of bareland and weeds, regardless of cutting time, particularly in summer season. However, 9 cm of stubble height maintained 80-85% of pasture grasses in all cutting times. In this experiment, therefore, cutting height was more important factor than annual cutting times for forage production and pasture longevity, and it is desirable to harvest 4-5 times per year (under this experimental field condition) with 9 cm of stubble height on woodland pasture.

• Journal of Ginseng Research
• /
• v.22 no.2
• /
• pp.102-113
• /
• 1998

This experiment used chlorophyll fluorescence techniques to assess the effect of irradiant during leaf development on photoinhibition of photosynthesis in Panax ginseng. Seedlings of p. ginseng were grown in the 91asshouse at four shade levels. The maximum mid-day irradiant in each treatment between emergence (January 4) and completion of the experiment (February 25) was 1220, 485, 235, 125 $\mu$mol/$\textrm{m}^2$/s. To assess the rapidity of photosynthetic readaptation to changes in light levels, fluorescence parameters (Fo, F, Fm, Fm', AF/Fm;, Fv/Fm) were measured for three days before and after transfer of plants (on February 21) from each light treatment into each of the other light treatments. Before transfer, dark adapted values of Fv/Fm in the 1220 (0.699) and 485 (0.739) treatments were different from each other and lower than values in the 235 (0.764) and 125 (0.768) treatments, indicating mild photoinhibition. Patterns of change in F during the day also differed between treatments, with low light treatments tracking irradiant levels, but F in the high light treatment (1220) declined in the morning, presumably due to fluorescence quenching. Although plants grown at high irradiant had relatively low photosynthetic efficiency, relative electron transport rate was greater than in lower irradiant treatments. After transfer, plants adopted the daily pattern of change in F of the treatment to which they were moved with little change in absolute levels of F, except in plants transferred from the highest (1220) to the lowest light level (125), where F increased over the course of the three days following transfer. After plants were transferred, Fm' converged on values similar to those in plants raised in the treatments to which they were moved. Values of Fv/Fm in plants moved from low to high light declined dramatically, but there was no decline in plants from 485 moved to 1220. Values of Pv/Fm in plants that were moved from high light to lower light increased to values above those recorded in plants raised in the lower light treatments. Reductions in quantum efficiency caused by photoinhibition at high irradiant may be more than compensated for by higher electron transport rates, although evidence suggests that under high irradiant this tends to be balanced by reduced leaf area and earlier senescence. Chlorophyll fluorescence techniques appear capable of indicating effects of irradiant induced stress in ginseng, yielding results comparable to those obtained with gas exchange techniques but in less time and with greater replication.

• Korean Journal of Plant Resources
• /
• v.26 no.5
• /
• pp.539-547
• /
• 2013

This study investigates the change of chemical components, antioxidant and antimutagenic activity in Glycyrrhiza uralensis Fischer stems and leaves (GU) by the various processing methods, as follows: fresh (GU-1), dried under the shade (GU-2), blanched (GU-3), roasted 3 times (GU-4), roasted 4 times (GU-5). The components have been identified and quantified through the use of gas chromatograph-mass spectrometry (GC-MS). At results, cis-1,3-dimethyl-2-methylenecyclohexaneat at 19.7 min and n-hexadecanoic acid at 21.5 min were detected in five kinds of extract. 3-O-Methyl-D-fructose at 17.8 min was observed in four extracts except in GU-1 and aminopyrazine at 19.8min was observed in four extracts except in GU-4. The total phenolics contents was high in GU-4(3.38 g/100 g). ABTS radical scavenging was high in GU-5($EC_{50}$, 0.57 ug) and DPPH radical scavenging was high in GU-4($EC_{50}$, 2.66 ug). The extracts of GU-3, GU-4, and GU-2 were most potent in anti-mutagenicity activity against 1-NP, Trip-P-1, and Trip-P-2, respectively. GU-3 and GU-4 also showed most potent effect of anti-mutagenicity on 2-AA and AFB1, respectively.

• Restorative Dentistry and Endodontics
• /
• v.22 no.2
• /
• pp.751-760
• /
• 1997

Resin-modified glass ionomers were introduced in 1988 to overcome the problems of moisture sensitivity and low early mechanical strengths of the conventional glass ionomers, and to maintain their dinical advantages. The purpose of this study was to evaluate the bi-axial fracture strength of four resinmodified glass-ionomers(Fuji II LC, Vitremer, Dyract, VariGlass), one resin composite material(Z-100), and one conventional glass-ionomer(Fuji II). Three specimens of each material and shade combination were made according to the manufacturers' instructions. Materials were condensed into metal mold with a diameter of 10mm and a thickness of 2.0mm and pressed between two glass plates. Resin-modified glass ionomers were polymerized using a Visilux II light curing unit by irradiating for 60 seconds from both sides, and conventional glass ionomer was cured chemically. After specimens were removed from the molds, surfaces were polished sequentially on wet sandpapers up to No. 600 silicone carbide paper. The specimens were thermocycled for 2,000 cycles between $5^{\circ}C$ and $55^{\circ}C$ distilled water. After thermocycling, bi-axial fracture strengths were measured using a compressive-tensile tester(Zwick 1456 Z020, Germany) with the cross head speed of 0.5mm/minute. The results were as follows: 1. Two factors of the kind and color of materials had a main effect on bi-axial fracture strength (p<0.01), and bi-axial fracture strength was influenced significantly by the kinds of materials (p<0.01). But there was no significant interaction between two variables of the kind and color of materials (p>0.05). 2. Comparing the mechanical properties of the materials, the elastic modulus of Z100 was higher than any other material, and there was no difference in the displacement at fracture among materials. The bi-axial fracture strength of Z100 was significantly higher than any other material, and that of resin-modified glass ionomers was significantly higher than that of conventional glass ionomer (p<0.05). 3. In the same material group, the color of material had little influence on the mechanical properties.

• Food Science and Preservation
• /
• v.24 no.5
• /
• pp.658-665
• /
• 2017

The current study was performed to investigate the changes of bio-activities of Salicornia europaea (SE) depending on the different dry methods. The ethanol extracts were prepared from the freeze-drying SE (FD), hot-air drying SE (HD), and shade drying SE (SD). Their anti-oxidant and anti-thrombosis activities were compared. The yields of ethanol extraction in FD, HD, and SD were 14.4, 13.2 and 11.9%, respectively. The highest contents of total polyphenol (4.6 mg/g) and total sugar (23.4 mg/g) were shown in FD, whereas, the highest content of reducing sugar (14.6 mg/g) was observed in HD. In anti-oxidation activity assay, the FD and HD showed similar radical scavenging activities and reducing power. However, in SD, nitrite scavenging activity and reducing power were severely decreased. In anti-coagulation activity assay, the thrombin time (TT), prothrombin time (PT) and activated partial thromboplastin time (aPTT) of FD, HD and SD did not show significant changes at 5 mg/mL concentration. But the HD at 7 mg/mL had strong inhibitions against thrombin and blood coagulation factors. The platelet aggregation and hemolysis activities were not affected by dry methods. Our results suggest that both FD and HD are effective to maintain the functional ingredient of SE, and HD is economic and efficient dry process for production of functional food.

• Korean Journal of Medicinal Crop Science
• /
• v.20 no.2
• /
• pp.124-128
• /
• 2012

When ginseng seedlings are cultured in paddy fields, quality degradation and yield reduction are induced by severe plant loss with chlorosis on leaves occurred physiological disorder by excessive salt and poor drainage, rusty-root occurrence, and root rot etc. Accordingly, in order to solve these problems, this study was performed to investigate the treatment method, concentrations and time of activated ion calcium as environment-friendly agricultural materials. Activated ion calcium is an enriched and purified water-soluble mineral calcium component for absorbing quickly into plant as a highly functional calcium and it is an alkaline calcium of 37% (370 $m{\ell}$/1 ${\ell}$) concentration with pH 13. Treatment method was that ginseng seeds were sown after removing water in the shade after seed immersion for 1 minute with active ion calcium of 20-fold diluted solution, and then irrigated $4{\ell}$ per 3.3 $m^2$ with 200-fold, 400-fold, and 600-fold diluted solution before emergence on late March, and supplied 1 time on leaves with 500-fold diluted solution in June and July respectively. The disease rate by treatment of activated ion calcium was that on the treatment of soil irrigated with 200-fold diluted solution compared to non-treated soil, damping-off was 33%, anthracnose was 100% reduced and the occurrence rate of rusty-root was 30% reduced. In addition, when active ion calcium of 200-fold diluted solution were soil irrigated, first and second grade ginseng were respectively 26% and 22% produced more, compared with control.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.23 no.6
• /
• pp.986-993
• /
• 1994

As a part of development of traditional foods, mugwort boogag and dry laver boogag were fried insoybean oil, and BHA or tocopherol-added soybean oil. They were wrapped up in opp vinyl film, and preserved at $4^{\circ}C(RH{\;}40{\pm}5%){\;}and{\;}25^{\circ}C(RH{\;}80{\pm}5%)$. During the storage of bobogags, acid value, peroxide value, and TBA value were investigated. Changes of sensory evaluation and texture profile were also examined. Boogags were manufactured by washing the raw materials. drying in the shade, mixing them with glutinous rice flour, and hot-air drying up it to 13 % of moisture contents after dryed it up to 80% of moisture contents on dry table for 23days, in order. These boogags were packaged to manufacture goods with dryed state or fried at $160^{\circ}C$ for 10 sec. Acid value, peroxide value, and TBA value of boogags which preserved at $4^{\circ}C$ generally appeared lower than at $25^{\circ}C$. As storage time goes by, moisture contents of bobogagas preserved at $25^{\circ}C$ increased and its quality were gradually deteriorated. When the boogags were fried in BHA(0.01%) and tocopherol (0.01%) added soybean oil, changes of acid value, peroxide value, TBA value were generally low. During the storage of bobogagas antioxidant effect of BHA was higher than that of tocopherol. Texture was inclined to decrease as storage time goes, by that of boogags preserved at $4^{\circ}C$ was a little more satisfactory. Hardness was also high.

• Restorative Dentistry and Endodontics
• /
• v.19 no.1
• /
• pp.124-134
• /
• 1994

The shade of restorative materials is very important for successful restoration esthetically harmonized with the natural tooth. The purpose of this study was to evaluate the color stability and the opacity change of conventional chemical setting and visible light curing glass-ionomer cements for restorative esthetic filling. Specimens of each brand (GC Fuji II and Fuji II LC) were uniformly prepared and divided into three groups: In group l(control group), the specimens received no surface treatment; in group 2, the specimens were coated with varnish and the excess gently blown off; and in group 3. the specimens were coated with light-cured bonding resin and irradiated by a visible light curing unit for 20 seconds on both sides. All specimens were stored in distilled water at $37^{\circ}C$ and checked after for 24 hours. 2 months. 4 months, 6 months. and 8 months. The color characteristics($L^*,\;a^*,\;b^*$) and the opacity(Y%) of all the samples were measured by a spectrocolorimeter and the total color differences(${\Delta}E^*$) and opacity changes(${\Delta}Y%$) were computed. The following results were obtained : 1. The total tolor differences in all groups increased with time. 2. The total color differences of the LC groups after immersion for 8 months in distilled water at $37^{\circ}C$ were lower than those of GC groups(p<0.01), and the total color differences of the varnish or the light-cured bonding resin coated groups were lower than those of the control group with glass-ionomer cements which had no surface treatment(p<0.01). 3. In all groups the translucency decreased with time. 4. In the control group and the varnish coating group. the opacity changes of the GC groups were lower than those of the LC groups(p<0.01) and in the light-cured bonding resin coated group, there was no significant difference between the GC group and the LC group. 5. The opacity changes of the varnish or the light-cured bonding resin coated groups were lower than those of the control group(p<0.01). These results suggest that color change and opacity of conventional chemical setting and light cured glass-ionomer cement were increased with time, and the color changes and the opacity changes of a control group after immersion for 8 months in distilled water at $37^{\circ}C$ were greater than those of the varnish or the light-cured bonding resin coated groups.

• Restorative Dentistry and Endodontics
• /
• v.34 no.3
• /
• pp.199-207
• /
• 2009

The objective of this study was to evaluate the effect of color measuring instrument by measuring the color of dental composite resins. Nine shade light cured composite resin disks were prepared (diameter : 15 mm, thickness : 4 mm). CIE $L^*a^*b^*$ color scale of each disk was measured with 3 different types of spectrophotometer [MiniScan XE plus (Model 4000S, Hunter Lab, USA), CM-3500d (Minolta, Japan) and Specbos 2100 Miniature VIS Reflection spectrometer (Serial No: 319416, JETI Technishe VIS Instrumentic GmbH. Germany)]. Miniscan XE Plus and CM-3500d using identical measuring geometry with different size of viewing aperture. But Specbos 2100 using different measuring geometry. Within the limitation of this study, there were color difference (${\Delta}E^*$) from 2.4 to 7.8 between Miniscan XE Plus and CM-3500d, but $L^*$, $a^*$, $b^*$ values showed the high correlation. However, there were great color difference (${\Delta}E^*$) in the extent of about 20 between instruments with the different measuring geometry. Therefore, color scale measured by color measuring instrument should be used as a relative value rather than an absolute value in the field of dentistry.