• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.729-734
• /
• 2000

This paper proposes virtual-magnetic system by a force-reflecting interface to drive a ultrasonic motors(USMs) To approach virtual magnet in graphic the 6 dDOF force-reflecting interfaces provides force feedback to users as if I is magnetic-force, So users can feel real magnet Effectively to display the magnetic-force we need the interface with specific characteristics such as low inertia almost zero friction and very high stiffness As an actuator for the interface the USMs have many good advantage satisfied these conditions over conventional servo motors. To estimate capability of this virtual-magnetic system we did an experiment of magnetism based on coulomb's law when Coulmb's low apply this experiment it is vey conformable to real magnet

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.41-45
• /
• 2001

This paper presents an implementation of motion control system of Switched Reluctance Motor (SRM) using digital hysteresis controller by TMS320F240 DSP. SRM position control system possess several advantages over other motors, including high efficiency, simple structure, low cost, and four-quadrant operation at a wide speed range, especially for the servo drive systems with precision, stability and fast response characteristics in the industrial applications. In the suggested motion control system, position control using digital hysteresis controller is developed, and is evaluated using experimental testing. The developed system for cost reduction and high-performance by fully digital controller is shown a good response characteristic of motion control results.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.615-619
• /
• 2000

This paper presents an implementation of digital motion control system of Surface Permanent-Magnet Synchronous Motor(SPMSM) vector drives with a direct torque control(DTC) using the 16bit DSP TMS320F240 The DSP controller enable enhanced real time algorithm and cost-effective design of intelligent control for motors which can be yield enhanced operation fewer system components lower system cost increased efficiency and high performance The system presented are stator flux and torque observer of stator flux feedback model that inputs are current and voltage sensing of motor terminal and angle for a low speed operating area two hysteresis band controllers an optimal switching look-up table and IGBT voltage source inverter by using fully integrated control software. The developed control system are shown a good motion control response characteristic results and high performance features using 1.0Kw purposed servo drive SPMSM.

• Journal of Power Electronics
• /
• v.9 no.5
• /
• pp.791-799
• /
• 2009

This paper presents a time-varying sinusoidal disturbance compensation method (based on an adaptive estimation scheme) for induction motor drives fed by a matrix converter. In previous disturbance accommodation methods, sinusoidal disturbances with unknown time-invariant frequencies have been considered. However, in the new method proposed here, disturbances with unknown time-varying frequencies are considered. The disturbances can be estimated by using a disturbance accommodating observer, and an additional control input is added to the induction machine drive. The stability analysis is carried out considering the disturbance estimation error and simulation results are shown to illustrate the performance of the proposed solution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.985-990
• /
• 1995

Recently, the development of high speed and high precision NC-lathe for piston head machining is needed for the complexity and diversity of the piston head shape used in automobile reciprocating engine. THe piston head has many complex shapes in the aspect of fuel economy, such as ovality, profile, double ovality and recess. Among them, for the maching of the over shape of 0.1~1mm the cutting tool should move periodically symchronized with the rotation of piston workpiece. The cutting tool feeed system must have high positioning accuracy for the precise machining, high speed for the fast maching and high dynamic stiffness for the cutting force. The linear brushless DC motor is used for satisfying these coditions. The ballbush guide and supporting guide using turcite is used for the guidance of the feed drive system. Linear encoder, digital servo ampllifer and controller are used for driving the motor. THis paper presents the design and simulation of the new tool feed system for noncircular machining.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.11-14
• /
• 2004

This paper presents an implementation of compact vector control system for induction motor using a digital signal processor (DSP) and a smart power module (SPM). The DSP TMS320F2812 has most necessary functions for ac motor control in a single chip and SPM provides a compact power stage. The indirect vector control algorithm is implemented in the drive system using these devices. The developed system is applied by 0.8kW induction servo motor and the all functions are verified through the experiments.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.76-79
• /
• 1988

The sliding mode control in an effective method to eatablish robustness against parameter variation and disturbance. But. In sliding mode strategy, the control function is discontinuous on the hyperplane. However the discontinuous change in control structure caves the controller input to chaffer and gives non-zero steady state error. Consequently, a multiloop feedback control system supplemented by a complelmentary controller is used to improved the drive performence of a DC servo motor and reduce sensitivity to parameter variation, nonlinear effects, and other disturbances.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.3B no.1
• /
• pp.52-58
• /
• 2003

The application of a sliding mode control for improving the dynamic response of an induction motor based speed control system is presented in this paper and provides attractive features, such as fast response, good transient performance, and insensitivity to variations in plant parameters and external disturbance. However, chattering is a difficult problem for which the sliding mode control is a popular solution. This paper presents a new fuzzy-sliding mode controller for a sensorless vector-controlled induction motor servo system to practically eliminate the chattering problem for traction applications. A DSP based implementation of the speed control system is employed. Experimental results are presented using a propulsion system simulator. The performance of the drive is shown to be practically free from chattering.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.156.5-156
• /
• 2001

Stabilized tracking platform in a missile consisting of a flat planar antenna, pitch/yaw gimbals, gear trains, and current controlled DC drive motors for pitch and yaw gimbal must have a capability to track a target as an inertial sensor in the presence of missile body motion such as maneuvering and vibration. Because of this reason, tracking a target from dynamic platform requires a servo architecture that includes a outer tracking loop(position loop) and inner rate loop that stabilizes the line of sight(LOS). This paper presents a gimbaled platform model including nonlinear phenomena due to viscous and Coulomb friction based on experimental data and torque equilibrium equation, the design concept for the inner tacholoop having P controller structure ...

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.2
• /
• pp.220-227
• /
• 1999

The position control accuracy of a robot arm is significantly deteriorated when a long slender arm robot is operated at a high speed. In this case, the robot arm needs to be modeled as a flexible structure, not a rigid one, and its control system needs to be designed with its elastic modes taken into account. In this paper, the vibration control scheme of a one-link flexible manipulator using adaptive input shaper in conjunction with PID controller is presented. The robot consists of a flexible arm manufactured with a thin aluminium plate, an AC servo motor with a harmonic drive for speed reduction, an optical encoder and an accelerometer. On-line identification of the vibration mode is done using the pruned decimation-in-time FFT algorithm to estimate the parameter of the input shaper. Experimental results of the flexible manipulator with a PID controller and input shaper are provided to show the effectiveness of the advocated controllers.