• 제어로봇시스템학회논문지
• /
• 제9권4호
• /
• pp.277-283
• /
• 2003

Recently, near-field recording (NFR) disk drive schemes have been proposed with a view to increasing recording densities of hard disk drives. Compared with hard disk drives. NFR disk drives have narrower track pitches and are exposed to more severe periodic disturbances resulting from eccentric rotation of the disk. It is difficult to meet servo system design specifications for NFR disk drives with conventional VCM actuators in that the servo system for an NFR disk drive generally requires a feater gain and higher bandwidth. To tackle the problem various dual-stage actuator systems composed of a microactuator mounted on top of a conventional VCM actuator have been proposed. This article deals with the problem of designing a tracking servo system far an NFR disk drive adopting a dual-stage actuator. We summarize design constraints pertaining to the dual-stage servo system and present a new servo scheme using iterative teaming control. We design feedback compensators and an iterative teaming controller for a target plant and verify the validity of the proposed control scheme through a computer simulation.

• 한국정밀공학회지
• /
• 제19권5호
• /
• pp.103-109
• /
• 2002

The paper investigates the change of frequency response characteristics on two-stage gear reduction servo system according to the variation of backlash amount of each gear reduction stage, under the condition that the backlash of total system is constant. It is shown that the frequency response characteristics of the system heavily depend on the contribution ratio which is defined as a ratio of the first backlash amount to the total backlash. It is also found that there is an optimal backlash combination to maximize the bandwidth of two-stage gear reduction servo system when the allowable total backlash is determined.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.46-51
• /
• 2001

To reach high areal density, less track pitch is expected and more servo bandwidth is required. One approach to overcoming the problem is by using dual stage servo system. In this system, a voice coil motor (VCM) is used as the primary stage while a milliactuator is used as the secondary stage. We have suggested new milliactuator based on the shear mode of piezoelectric elements to drive the head suspension assembly. In this paper, we introduce controller design method, PQ method. PQ method reduces the controller design problem for DISO(dual-input/single-output) systems to two standard controller design problems for SISO(single-input/single-output) problems. The first part of PQ method directly address the issue of actuator output contribution, and the second part allows the use of traditional loop shaping to achieve the overall system performance. This paper shows how to employ the PQ method to meet aggressive close-loop performance specifications for a disk drive system with a VCM and piezoelectric milliactuator.

• 전기의세계
• /
• 제14권2호
• /
• pp.14-24
• /
• 1965

The characteristics of servo-multipliers and its accuracies are analyzed. From the analysis a low cost high accuracy four quadrant servo-multiplier with first derivative output feedback is built. The multiplier servomechanism has a second order system response with a damping ratio of 0.8 and computing bandwidth of 4 cycles per second, and its tracking accuracy at low speed of 0.5 volt per second is 0.9 per cent of maximum output voltage and static accuracy is better than 0.6 per cent. Method of testing this multiplier and the results are also described. The test on the characteristics of the multiplier shows that the results agree with theoretical values satisfactorily, and justifies the use of the servo-multiplier for slow type analog computers.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.237-242
• /
• 2000

The areal recording density of HDD(Hard Disk Drive) has been increasing by about 60% a year. In order to achieve high areal density, less track pitch is expected and more servo bandwidth is required. Dual stage actuator and servo controller for HDD have been suggested for achieving high track density as a possible solution. Dual-loop servo system is generally classified into a two-input-two-output system, but if we use an estimator for a two-input-two-output system, it can be converted into two input one output system. Since we can't control the dual stage servo system by the classical method, it requires a special technique; for example, Parallel Loop System, Master-Slave Loop System, Decoupled Master-Slave Loop System, and Dual Feedback Loop System. In this paper, we performed experimental evaluations of several types of control algorithm. Further experiments will be made in the future.

• 드라이브 ㆍ 컨트롤
• /
• 제10권4호
• /
• pp.22-28
• /
• 2013

Mechanical and electrical properties of a DDV(Direct Drive servo Valve) with electric feedback are analysed via reverse analysis technique in this work. The DDV is disassembled and mechanical parameters, such as spool mass, spring stiffness and port size are identified. The servo amplifier, which is built in the valve, is reversely analysed and the control scheme and gains for several control actions are also identified. The electrical feedback for spool displacement improves much better the valve performance, such as hysteresis and dynamic bandwidth frequency, than an ordinary mechanical feedback valve. Integrating control action with very large gain was adopted in the valve amplifier, and it seemed to give high performance.

• 드라이브 ㆍ 컨트롤
• /
• 제18권2호
• /
• pp.9-19
• /
• 2021

The spool displacement signal of a directional control valve, including the servo valve, can be considered as the standard signal to measure dynamic characteristics. When the spool displacement signal is not available, the velocity signal of a metering cylinder piston can be used. In this study, the frequency response characteristics of the metering cylinder are investigated for the spool displacement input. The transfer functions of the servo valve-metering system are derived taking into consideration the oil inertia effect in the transmission lines. The theoretical results of the transfer functions are verified through computer simulations and experiments. The oil inertia effect in the transmission lines was found to have a very significant effect on the bandwidth frequency of the servo valve-metering cylinder system. In order to more precisely measure the dynamic characteristics of a servo valve, the metering cylinder should be set up to minimize the oil inertia effect by increasing the inner diameters of the transmission lines or shortening their lengths.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.134-139
• /
• 2002

This paper presents a servo design method for high track-density hard disk drives, in which the plant time delay, mainly due to the processor computation time, is taken into account. The key idea behind the proposed design method is to incorporate the delay model into the output equation of the state-space representation for the plant model; thereby, the delay is accounted for by a standard state observer in a natural manner, with simplified state equations as compared to those for conventional methods. The results from practical application confirm that the proposed method is quite effective in realizing a high-bandwidth servo system in hard disk drives.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.653-657
• /
• 1996

This paper presents adaptive cutting force control in milling process using indirect cutting force measurement. The cutting forces in X, Y, and Z axes are measured indirectly from the sensing current of the feed-drive servo motor. After modelling the feed-drive system of a horizontal machining center, the relation between the cutting force and the servo motor current is analyzed. The pulsating milling forces are measured from the sensing current within the bandwidth of the servo. It is shown that indirect cutting farce measurement can be used in adaptive cutting force control. The adaptive control scheme which is globally convergent and stable is attached to a commercial CNC machining center. Cutting experiments on end milling are performed for diagonal cutting.

• 대한기계학회논문집A
• /
• 제29권5호
• /
• pp.743-753
• /
• 2005

The model of azimuth driving servo system with a flexible antenna in a prototype gimbal has been derived in this work. The validity of the model is verified by comparing the result of the model with that of experiment. It is found that one should consider an antenna as a flexible body in case of modeling the dynamics of the gimbal with an antenna. It is also known that the effect of reducing backlash magnitude for extending the bandwidth in the system with a flexible antenna is smaller than the system with a stiff antenna. It is thought that the model-based design optimization of the gimbal with an antenna will be possible by virtue of the derived model, when a weight reduction and a bandwidth extension are required.