• Korean Journal of Soil Science and Fertilizer
• /
• v.48 no.5
• /
• pp.391-396
• /
• 2015

Arsenic (As) contamination of agricultural soils resulting from mining activity has caused major concern due to the potential health risk. Therefore the current study was carried out to investigate the relationship between fractionation of As in soil and rice uptake and to provide a basic information for adequate management of As contaminated agricultural soil. Twenty agricultural soils and rice affected by the abandoned mining sites were collected. Soil chemical properties and As concentrations (total and sequential extracted) in soils were determined and As concentrations in polished rice were analyzed. The average concentration of As in non-specifically adsorbed (F1), specifically adsorbed (F2), amorphous hydrous oxides of Fe and Al (F3), crystalline hydrous oxides of Fe and Al (F4) and residual phase (F5) were 0.08, 1.38, 10.34, 3.26 and $10.98mgkg^{-1}$, respectively. Both soil pH and available phosphorus were positively correlated with the concentrations of As in F1 and F2. These results indicate that increasing the soil pH and available phosphorus can significantly increase the easily mobile fractions of As (F1 and F2). The average concentration of As in polished rice was $0.09mgkg^{-1}$. The concentrations of As in F1 and F2 showed a positive correlation with the concentrations of As in polished rice. Therefore soil pH and available phosphorus affect the distribution of As fractionation in soils and thus affect As bioavailability.

• Journal of the HCI Society of Korea
• /
• v.14 no.1
• /
• pp.15-22
• /
• 2019

The purpose of this study is to investigate the users' expectation and expectation gap about the attributes of smart speaker as an intelligent agent, ie autonomy, sociality, responsiveness, activeness, time continuity, goal orientation. To this end, semi-structured interviews were conducted for smart speaker users and analyzed based on ground theory. Result has shown that people have huge expectation gap about the sociality and human-likeness of smart speakers, due to limitations in technology. The responsiveness of smart speakers was found to have positive expectation gap. For the memory of time-sequential information, there was an ambivalent expectation gap depending on the degree of information sensitivity and presentation method. We also found that there was a low expectation level for autonomous aspects of smart speakers. In addition, proactive aspects were preferred only when appropriate for the context. This study presents implications for designing a way to interact with smart speakers and managing expectations.

• Journal of Powder Materials
• /
• v.28 no.2
• /
• pp.127-133
• /
• 2021

One-dimensional (1D) piezoelectric nanostructures are attractive candidates for energy generation because of their excellent piezoelectric properties attributed to their high aspect ratios and large surface areas. Vertically grown BaTiO₃ nanotube (NT) arrays on conducting substrates are intensively studied because they can be easily synthesized with excellent uniformity and anisotropic orientation. In this study, we demonstrate the synthesis of 1D BaTiO₃ NT arrays on a conductive Ti substrate by electrochemical anodization and sequential hydrothermal reactions. Subsequently, we explore the effect of hydrothermal reaction conditions on the piezoelectric energy conversion efficiency of the BaTiO₃ NT arrays. Vertically aligned TiO₂ NT arrays, which act as the initial template, are converted into BaTiO₃ NT arrays using hydrothermal reaction with various concentrations of the Ba source and reaction times. To validate the electrical output performance of the BaTiO₃ NT arrays, we measure the electricity generated from each NT array packaged with a conductive metal foil and epoxy under mechanical pushings. The generated output voltage signals from the BaTiO₃ NT arrays increase with increasing concentration of the Ba source and reaction time. These results provide a new strategy for fabricating advanced 1D piezoelectric nanostructures by demonstrating the correlation between hydrothermal reaction conditions and piezoelectric output performance.

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4514-4521
• /
• 2022

In this study, the effects of heat and radiation on the degradation behaviour of fluoroelastomer under simulated normal operation and a severe accident environment were investigated using sequential testing of gamma irradiation and thermal degradation. Tensile properties and Shore A hardness were measured, and thermogravimetric analysis was used to evaluate the degradation behaviour of fluoroelastomer. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy were used to characterize the structural changes of the fluoroelastomer. Heat and radiation generated in nuclear power plant break and deform the chemical bonds, and fluoroelastomer exposed to these environments have decreased C-H and functional groups that contain oxygen and double bonds such as C-O, C=O and C=C were generated. These functional groups were formed by auto oxidation by reacting free radicals generated from the cleaved bond with oxygen in the atmosphere. In this auto oxidation reaction, crosslinks were generated where bonded to each other, and the mobility of molecules was decreased, and as a result, the fluoroelastomer was hardened. This hardening behaviour occurred more significantly in the severe accident environment than in the normal operation condition, and it was found that thermal stability decreased with the generation of unstable structures by crosslinking.

• Geomechanics and Engineering
• /
• v.29 no.4
• /
• pp.391-405
• /
• 2022

A newly proposed grouting simulation method, the sequential diffusion solidification method was introduced into the numerical simulation of combined bi-borehole grouting. The traditional, critical and difficult numerical problem for the temporal and spatial variation simulation of the slurry is solved. Thus, numerical simulation of grouting and blocking of flowing water in karst conduits is realized and the mechanism understanding of the combined bi-borehole technology is promoted. The sensitivity analysis of the influence factors of combined bi-borehole grouting was investigated. Through orthogonal experiment, the influences of proximal and distal slurry properties, the initial flow velocity of the conduit and the proximal and distal slurry injection rate on the blocking efficiency are compared. The velocity variation, pressure variation and slurry deposition phenomenon were monitored, and the flow field characteristics and slurry outflow behavior were analyzed. The interaction mechanism between the proximal and distal slurries in the combined bi-borehole grouting is revealed. The results show that, under the orthogonal experiment conditions, the slurry injection rate has the greatest impact on blocking. With a constant slurry injection rate, the blocking efficiency can be increased by more than 30% when using slurry with weak time-dependent viscosity behavior in the distal borehole and slurry with strong time-dependent viscosity behavior in the proximal borehole respectively. According to the results of numerical simulation, the grouting scheme of "intercept the flow from the proximal borehole by quick-setting slurry, and grout cement slurry from the distal borehole" is put forward and successfully applied to the water inflow treatment project of China Resources Cement (Pingnan) Limestone Mine.

• Structural Engineering and Mechanics
• /
• v.87 no.1
• /
• pp.47-56
• /
• 2023

Any pre-existed delamination defect present during manufacturing or induce during service loading conditions in the wingskin adherend invariably shows a greater loss of structural integrity of the spar wingskin joint (SWJ). In the present study, inter-laminar delamination propagation at the critical location of the SWJ has been carried out using contact and multi-point constraint finite elements available with commercial FE software (ANSYS APDL). Strain energy release rates (SERR) based on virtual crack closure technique have been computed for evaluation of the opening (Mode-I), sliding (Mode-II) and cross sliding (Mode-III) modes of delamination by sequential release of multi point constraint elements. The variations of different modes of SERR are observed to be significant by considering varied delamination lengths, material properties of adherends and radius of curvature of the SWJ panel. The SERR rates are seen to be much different at the two pre-embedded delamination ends. This shows dissimilar delamination propagation rates. The maximum is seen to occur in the delamination front in the unstiffened region of the wingskin. The curvature geometry and material anisotropy of SWJ adherends significantly influences the SERR values. Increase in the SERR values are observed with decrease in the radius of curvature of wingskin panel, keeping its width unchanged. SWJs made with flat FRP composite adherends have superior resistance to delamination damage propagation than curved composite laminated SWJ panels. SWJ made with Boron/Epoxy (B/E) material shows greater resistance to the delamination propagation.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.1
• /
• pp.43-50
• /
• 2024

Large planar military antenna boasts a range of electrical components, including TRA(Transmit-Receive Assembly), signal processors, etc. which engage in computations and calculations. These processes generate a significant amount of heat, leading to unforeseen consequences for the equipment. To mitigate these adverse effects, it's imperative to implement a cooling system that can effectively reduce heat-related issues. Given the antenna's intricate nature and the multitude of components it houses, a two-step estimation process is necessary. The first step involves a comprehensive model calculation to determine the total flow characteristics, while the second step entails a thermal analysis of individual TRA set. In this study, we depicted an antenna set using simplified 3D models of its components, considering their material and thermal properties. The sequential analysis process facilitated the calculation of branched flow rates, providing insights into the individual TRA. This approach also allowed us to design a cooling system for the TRA set, assessing its thermal stability in high-temperature environments. To ensure the optimal performance of TRA, breaking down the analysis into stages based on the cooling system's structure can assist operators in predicting numerical results more effectively.

• Korean Journal of Soil Science and Fertilizer
• /
• v.24 no.3
• /
• pp.183-191
• /
• 1991

A study was conducted to determine the influence of soil chemical properties on the distribution and forms of cadmium (Cd), lead (Pb), copper(Cu) and Zinc(Zn) in paddy soils near zinc mines. A sequential extraction procedure was used to fractionate the heavy metals in soils into the designated from of water soluble, exchangeable, organically bound, oxide/carbonate, and sulfide/residual. The predominant form of Cd, Pb, Cu and Zn in the soils was found to be sulfide/residual form. Oxide/carbonate Cd and Pb and organically bound Cu were high, while exchangeable Pb and Cu were very low. Water soluble Cd, Pb and Cu were not detected in the soils. The percentages of the heavy metals content in exchangeable fractions were inversely correlated with those in sulfide/residual fractions in the soils. Exchangeable Cd and Zn and the oxide/carbonate Pb were shifting to the sulfide/residual form with soil depth and the chemical forms of Cu were not changed. Organically bound Cu was positively correlated with soil organic matter content but Cd, Pb and Zn were not. The percentages of Cd, Pb and Zn content in exchangeable forms decreased with soil pH, while those in oxide/carbonate and sulfide/residual forms increased with soil pH. The amounts of oxide/carbonate and sulfide/residual forms of pb were higher than those of Cd and Zn at same soil pH.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.1
• /
• pp.100-110
• /
• 2016

Alkaline Peroxide Mechanical Pulping (APMP) of Pinus densiflora harvested from domestic mountains was explored. APMP contributes to various advantages including pulp quality, elimination of the need for a bleaching process, and energy savings. Sequential treatment of impregnation of bleaching chemicals and refining not only overcome the concern of alkaline darkening of wood chips during chemical impregnation, but it also brightens the chips to the desired brightness levels suitable for writing and printing papers. APMP pulping from Pinus densiflora was greatly influenced by the dosage levels of hydrogen peroxide and sodium hydroxide. Alkaline peroxide treatment was carried out by applying one of three levels of hydrogen peroxide (1.5, 3, and 4.5% based on the oven-dried weight of the wood chips) and one of three levels of sodium hydroxide (1.5, 3, and 4.5% based on the oven-dried weight of the wood chips). Other chemicals including a peroxide stabilizers and metal chelation were constantly added for all treatments. Chemical treatment with a liquor-to-wood ration of 9:1 was carried out in a laboratory digestor. Compared to BTMP, APMP pulping displayed outstanding characteristics including the less requirement of refining energy, the better improvement of tensile strength, the more reduction of shives, and the greater increase of pulp brightness. In particular, when 4.5% of hydrogen peroxide with impregnation during 90 minutes was used, the brightness of APMP reached 64.9% ISO. Even though bulk of APMP was decreased with the increase of sodium hydroxide, a better and improved balance could be achieved between optical and strength properties. The spent liquor obtained from the discharge of the impregnation process at the dosage level of 4.5% hydrogen peroxide exhibited an equal level of residual peroxide with BTMP. In conclusion, APMP pulping showed successful results with Pinus densiflora due to its better response to the development of optical and physical properties compared to TMP pulping.

• The Journal of Engineering Geology
• /
• v.24 no.4
• /
• pp.643-648
• /
• 2014

Understanding of fracture networks and rock mass properties during tunnel construction is extremely important for the prediction of dangers during excavation, and for deciding on appropriate excavation techniques and support. However, rapid construction process do not allow sufficient time for surveys and interpretations for spatial distributions of fractures and rock mass properties. This study introduces a new statistical approach for predicting joint distributions at foreside of current excavation face during the excavation process. The proposed methodology is based on a cumulative space diagram for joint sets. The diagram displays the cumulative spacing between adjacent joints on the vertical axis and the sequential position of each joint plotted at equally spaced intervals on the horizontal axis. According to the diagram, the degree of linearity of points representing the regularity of joint spacing; a linear trend of the points indicates that the joints are evenly spaced, with the slope of the line being directly related to the spacing. The linear points which are stepped indicates that the fracture set show clustered distribution. A clustered pattern within the linear group of points indicates a clustered joint distribution. Fractures surveyed from an excavated space can be plotted on this diagram, and the diagram can then be extended further according to the plotted diagram pattern. The extension of the diagram allows predictions about joint spacing in areas that have not yet been excavated. To test the model, we collected and analyzed data during excavation of a 10-m-long tunnel. Fractures in a 3-m zone behind the excavation face were predicted during the excavation, and the predictions were compared with observations. The methodology yielded reasonably good predictions of joint locations.