• 한국전자통신학회논문지
• /
• 제3권4호
• /
• pp.266-275
• /
• 2008

본 논문에서는 전동기 파라미터와 부하에 강인한 속도 특성을 위해 디지털 IP제어를 이용한 BLDC 전동기의 센서리스 속도제어 방식을 제안한다. 단자 전압을 이용한 BLDC 전동기의 센서리스 구동시 회전자 위치 추정을 위해 아날로그 필터를 사용하기 때문에 부하나 속도에 영향을 받는다. 전동기 파라미터에 둔감하고 부하의 영향에도 강건한 센서리스 속도제어를 하기 위해서는 정확한 회전자 위치 추정과 연동하는 강인한 속도 제어기가 필요하다. 본 논문에서는 디지털 IP제어를 이용하여 부하의 변동에도 강인한 정속제어와 일정 부하로 운전 중 가감속시 임의의 속도변화에 대해 BLDC 전동기의 안정된 센서리스 제어가 가능하도록 구성하였다. 이에 대한 타당성은 실험을 통하여 입증하고자 한다.

• 조명전기설비학회논문지
• /
• 제28권9호
• /
• pp.1-7
• /
• 2014

Brushless Direct Current(BLDC) Motor is essential to measure a rotor position because of that this motor type needs to synchronize the rotor's position and changeover phase current instead of a brush and commutator used on the existing dc motor. Recently, many researches have studied on sensorless control drive for BLDC motor. The conventional control methods are a compensation value dq, Kalman filter, Fuzzy logic, Neurons neural network, and the like. These methods has difficulties of detecting BEMF accurately at low speed because of low BEMF voltage and switching noise. And also, the operation is long and complex. So, it is required a high-performance microprocessor. Therefore, it is not suitable for a small BLDC motor sensorless drive. This paper presents control methods suitable for economic small BLDC motor sensorless drive which are an improved design of the BEMF detection circuit, simplifying a complex algorithm and computation time reduction. The improved motor sensorless drive is verified stability and validity through being designed, manufactured and analyzed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.79-83
• /
• 1997

The inverter fed BLDC(Brushless DC) motor has been increasingly applied to industry and home appliances due to the advance of power electronics and permanent magnet technology, and its high efficiency and good acoustic noise characteristics. The BLDC motor and drives, however, require the rotor position sensors that may cause some problems such as the high cost and space. In this paper, sensorless algorithm for an interior permanent magnet BLDC motor is proposed. The maximum torque per ampere operation with advance angle considering load torque and speed was simulated and verified through the experiment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1144-1145
• /
• 2007

This paper is investigated the sensorless drive for BLDC motor using microprocessor. Since the BLDC motor should be commutated according to a rotor position, the sensors are required to detect the position. But the sensors increase cost and volume, complicate the motor configuration, and do not operate properly in some operating environments such as high temperature conditions, so that the necessity of sensorless commutation algorithm is getting increased. This paper is proposed the method to drive BLDC motor without position-detecting sensor using Back EMF. Back EMF commutation method was implemented the sensorless drive system which could control the rotational speed and monitor the behavior of a motor.

• 산업기술연구
• /
• 제35권
• /
• pp.9-13
• /
• 2015

In this paper, a new excitation scheme is developed to increase the output torque of the sensorless BLDC(Brushless DC) motor(BLDCM), which drives fins to control the flight attitude of a guided artillery munition. The proposed scheme is based on a 12-step excitation strategy combining two-phase and three-phase excitations. The proposed 12-step excitation scheme can produce more torque than a typical 6-step scheme for the start-up and synchronous operation in the sensorless BLDCM drive. The simulation and experimental results on the sensorless BLDCM drive system to control the fin were verified the validity of the proposed scheme.

• 전력전자학회논문지
• /
• 제11권5호
• /
• pp.440-446
• /
• 2006

BLDC 전동기와 같은 영구자석 전동기는 토크 각에 따라 출력 토크의 변화가 크기 때문에 원활한 기동 특성을 얻기 위해서는 회전자의 초기 위치 정보가 필수적으로 요구된다. 본 논문에서는 냉장고용 왕복동 압축기의 구동을 위해 사용되는 BLDC 전동기의 센서리스 구동장치에서 원활한 기동 특성을 얻기 위한 새로운 기동 제어 방식을 제안한다. 제안된 방식은 전동기의 전류 응답 특성으로부터 파악된 회전자 위치 정보를 이용하여 BLDC 전동기를 기동하는 방식으로, 압축기의 기동 부하 변동에 강인한 기동 특성을 가진다. 실험을 통하여 제안된 방식의 효과를 입증하였다.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.114-121
• /
• 2013

High efficiency operation is required for motors of vehicle to increase fuel efficiency due to the regulation of exhaust gas. This paper presents a control method of fuel pressure to increase fuel efficiency and a sensorless control method of BLDC motor to get higher efficiency than conventional brushed DC motor. Initial rotor position of BLDC motor is detected from current value that is occurred by test voltage pulse and rotor is accelerated by defined sequence to enter sensorless operation mode. The algorithm to control flow rate of fuel pump uses PI controller that is control motor speed to maintain the target fuel pressure commanded by ECU.

• 전력전자학회논문지
• /
• 제13권1호
• /
• pp.63-69
• /
• 2008

구형파 BLDC (Brushless DC) 전동기를 구동시키기 위해서는 전동기의 회전자 위치에 대한 정보를 아는 것이 필수적이다. 본 논문에서는 회전자 위치를 검출하기 위해 일반적으로 사용되는 홀센서나 엔코더를 이용하지 않고 각상을 저항으로 Y결선하여 만들어지는 단자의 전압에 포함되어 있는 역기전력을 클램프 회로를 통한 필터회로를 이용하여 전동기의 회전자 위치를 검출하는 구형파 BLDC 전동기를 위한 센서리스 드라이브 시스템을 제안한다. 특히 본 논문에서 제안한 새로운 역기전력 증폭 제한 회로를 통한 필터회로를 구성하여 저속영역에서 센서리스를 특성을 개선하였다. 그리고 이를 실제로 100[W]급 BLDC 구동용 프로토 타입 드라이브를 제작하여 제안된 역기전력 증폭 제한 회로의 타당성 검증하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권1호
• /
• pp.24-30
• /
• 1996

BLDC motor is widely used as a servo motor, because it has high efficiency, high power ratio, low inertia, and easy maintenance. However, position and speed sensors generally attached in BLDC motor increase motor cost, and limit environments of application. This study describes a sensorless speed control of sinusoidal BLDC motor using the d-q transformed instantaneous voltage equation, and presents the result of computer simulation. The sensorless algorithm is applied to the casse of a voltage controlled PWM inverter. The result indicates good dynamics and a robust control in cases of a load change and a system parameter variation.

• 전기학회논문지
• /
• 제60권10호
• /
• pp.1858-1864
• /
• 2011

This paper suggests a control technique of the sensorless brushless DC (BLDC) motor drive for a vehicle fuel pump application. The sensorless technique based on a comparator and a potential start-up method with high starting torque are proposed. The comparator is used to generate the commutation signals in phase with the three-phase back-EMFs. The rotor position is aligned at standstill for maximum starting torque without an additional sensor and any information of motor parameters. Also, the stator current can be easily adjusted by modulating the pulse width of the switching devices during alignment. Some experiments are implemented on a single chip 16-bit DSP controller to demonstrate the feasibility of the sensorless techniques.