• Laser Solutions
• /
• v.7 no.3
• /
• pp.11-24
• /
• 2004

In automotive industry, light weight vehicle is one of issues because of the air pollution and the protection of environment. Therefore, automotive manufacturers have tried to apply light materials such as aluminum to car body. Aluminum welding using laser has some advantages high energy density and high productivity. It is very important to understand behavior of plasma and keyhole in order to improve weld quality and monitor the weld state. In this study, spectral analysis was carried out to verify the spectrum for plasma which is generated in laser welding of A 6000 aluminum alloy. Two photodiodes which cover the range of plasma wavelength was used to measure light emission during laser welding according to assist gas flow rate and welding speed. Analysis of relationship between sensor signals of welding variables and formation of keyhole and plasma is performed. To determine the level of significance, analysis of variation (ANOVA) was carried out.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.63-67
• /
• 2020

This study investigated the influence of various sintering pressures of ZnS nanoparticles prepared by hydrothermal synthesis performed at 220 ℃ for 20 h. The hydrothermally synthesized ZnS nanoparticles formed a cubic phase. The ZnS nanoparticles were sintered using a hot-press process at 850 ℃ for 2 h under pressures of 10, 20, 30, 40, 50, 60, and 70 MPa. The ZnS ceramics indicate the cubic phase is the major phase and the hexagonal phase is the minor phase. In the ZnS ceramics, as the sintering pressure increased, a decrement in the hexagonal phase was confirmed. When the sintering pressure equaled or exceeded 30 MPa, the transmittance and density improved with reductions in porosity and hexagonal phase. A sintering pressure of 60 MPa delivered the highest transmittance (69.7%).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.182-182
• /
• 2014

Multiferroic materials have attracted much attention due to their own fascinating fundamental physical properties and potential technological applications to magnetic/ferroelectric data storage systems, quantum electromagnets, spintronics, and sensor devices. Among single-phase multiferroic materials, $BiFeO_3$, in particular, has received considerable attention because the enhanced ferromagnetism was found by the Fe-site ion substitution with magnetic ions. The structural, the magnetic and the ferroelectric properties of polycrystalline $BiFe_{1-x}Ni_xO_3$ (x=0, 0.01, 0.02, 0.03 and 0.05), which were prepared by the solid-state reaction and the rapid-sintering method, have been investigated. The x-ray diffraction patterns reveal that all the samples are in single phase and show rhombohedral structure with R3c space group. The magnetic properties are enhanced according to the doping content. The Ni-doped $BiFeO_3$ samples exhibit lossy P-E loop due to the oxygen vacancy. The leakage current density of Ni-doped samples (x=0.01 and 0.02) is increased by four orders of magnitude. On the other hand, the x=0.03 and 0.05 samples show the relative reduction of the leakage current.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.210.2-210.2
• /
• 2014

Recently, molybdenum disulfide (MoS2) nanostructures have been investigated for applications of lithium-ion batteries, solar cell, and gas sensors. In this regard, we have studied atomic and electronic properties of MoS2 nanostructures with adsorbed atoms and molecules using density functional theory calculations. Our calculations reveal that the several atoms such as H, C, N, and F are chemically bound to several sites on the two-dimensional (2D) MoS2 surface. On the other hand, various contamination molecules such as CO, CO2, NO, NO2, and NH3 do not bind to the surface. Next, adsorption of various molecules on the one-dimensional (1D) armchair MoS2 nanoribbon is investigated. Contrary to the case of 2D MoS2 monolayer surface, some molecules (CO and NO) are bound well to the edge of the MoS2 nanoribbon. We find that the molecular states due to adsorption are located near the Fermi level, which makes the band gap narrower. Therefore, we suggest that monolayer MoS2 nanoribbons be used as the gas sensors or detectors.

• Applied Science and Convergence Technology
• /
• v.27 no.2
• /
• pp.30-34
• /
• 2018

Conducting and semiconducting temperature sensors are calibrated and applied to cryomodules. The definition of temperature is introduced and the pressure in vacuum is shown as a function of temperature. The resistance of Drude model is shown as a function of carrier density and mean free path. Temperature sensors are calibrated with Physical Property Measurement System (PPMS). The temperature sensors are applied to measure temperature accurately in RAON cryomodules.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.4
• /
• pp.1063-1075
• /
• 2012

To locate an object accurately in the wireless sensor networks, the distance measure based on time-delay plays an important role. In this paper, we propose a maximum likelihood (ML) time-delay estimation algorithm in multi-path wireless propagation channel. We get the joint probability density function after sampling the frequency domain response of the multi-path channel, which could be obtained by the vector network analyzer. Based on the ML criterion, the time-delay values of different paths are estimated. Considering the ML function is non-linear with respect to the multi-path time-delays, we first obtain the coarse values of different paths using the subspace fitting algorithm, then take them as an initial point, and finally get the ML time-delay estimation values with the pattern searching optimization method. The simulation results show that although the ML estimation variance could not reach the Cramer-Rao lower bounds (CRLB), its performance is superior to that of subspace fitting algorithm, and could be seen as a fine algorithm.

• Journal of Sensor Science and Technology
• /
• v.14 no.3
• /
• pp.206-210
• /
• 2005

The SOI structure with buried alumina was fabricated by ALD followed by bonding and etchback process. The interface of alumina and silicon was analyzed by CV measurements and cross section was investigated by SEM analysis. The density of interface state of alumina and silicon was 2.5E11/$cm^{2}$-eV after high temperature annealing for wafer bonding. It was confirmed that the surface silicon layer was completely isolated from substrate by cross section SEM and AES depth profile. The device on this alumina SOI structure would have better thermal properties than that on conventional SOI due to higher thermal conductivity of alumina than that of silicon dioxide.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.9
• /
• pp.721-728
• /
• 1991

In this paper, a magneto-optic modulator has been designed by using single crystal BSO and polycrystal ZnSe as Faraday cells. And practical core-type optical current sensors using pure iron and permalloy have been prepared and experimented. In order to obtain efficient magnetic field detection, LED(NEC OD08358, 0.87 $\mu$m) was used as optical source, PIN-PD(OD-8454)as optical receiver and multi-mode optical fiber (100/140$\mu$m) as transmission line. The characteristics matrix of the optical element was calculated by Stokes parameter, and optic modulation characteristics equations were derived by Muller matrix. Electromagnetic analysis program (FLUX 2D, micro VAX 3600) by finite element method was used to find the magnetic flux density around the core. The measuring error of the output voltage to input current has been masured below 5% in the range of 50A to 1000A. As the temperature was changed from -20$^{\circ}C$ to 60$^{\circ}C$, the maximum measurement error of the optical output has been found to be 0.5% at 60$^{\circ}C$. These experimental results show good temperature and linearity characteristics. The SNR of the overall system was 47dB in case of 600A (250.2 Oe) conductor current and the system has good noise immunity.

• Corrosion Science and Technology
• /
• v.16 no.4
• /
• pp.194-200
• /
• 2017

Stress-corrosion cracking (SCC) of alloy 600 and alloy 800 in 0.5 mol/L thiosulfate solution during constant strain was investigated using electrochemical noise (EN) combined with 3-D microscope techniques. The in-situ morphology observation and EN results indicate that the SCC process could be divided into three stages: (1) passive film stabilization and growth, (2) crack initiation, (3) and crack growth. Power Spectral Density (PSD) and the probability distribution obtained from EN were used as the "fingerprint" to distinguish the different processes. During passive film stabilization and growth, the current noise signals resembled "white noise": when the crack initiated, many transient peaks could be seen in the current noise and the wavelet energy at low frequency as well as the noise resistance decreased. After crack propagation, the noise amplitudes increased, particularly the white noises at low and high frequencies ($W_L$ and $W_H$) in the PSDs. Finally, the detection of metal structure corrosion in a simulated sea splash zone and pipeline corrosion in the atmosphere are established.

• Applied Science and Convergence Technology
• /
• v.25 no.6
• /
• pp.124-127
• /
• 2016

Humidity calibration for a temperature-stable quartz oscillator (TSQO) was investigated to exclude the influences of relative humidity on the TSQO output in order to use the corresponding devices outdoors. The TSQO output is a voltage that is inversely proportional to the electric impedance of the quartz oscillator, which depends on the viscosity and density of the measured gas. The TSQO output was humidity calibrated using its humidity dependence, which was obtained by varying the relative humidity (RH) from 0 to 100 RH% while other conditions were kept constant. The humidity dependencies of the TSQO output were fit by a linear function. Subtracting the change in the TSQO output induced by the change in humidity, calculated with the function from the experimentally measured TSQO output for a range of 0-100RH%, eliminated the influence of humidity on the TSQO output. The humidity calibration succeeded in reducing the fluctuations of the TSQO output from 0.4-3% to 0.1-0.3% of the average values for a range of 0-100RH%, at constant temperatures. The necessary stability of the TSQO output for application in hydrogen sensors was below one-third of the change observed for a hydrogen leakage of 1 vol.% hydrogen concentration, corresponding to 0.33% of the change in each background. Therefore, the results in this study indicate that the present humidity calibration effectively suppresses the influence of humidity, for the TSQO output for use as an outdoor hydrogen sensor.