• Journal of Korean Society of Steel Construction
• /
• v.29 no.4
• /
• pp.269-280
• /
• 2017

In this study, seismic performance was evaluated for the exposed column-base plate weak-axis connections of small size steel structures through cyclic loading tests. The primary test parameters are the thickness of base plate, the presence of rib plates, the number of anchor bolts and embedment length of anchor bolts. To investigate the effect of bond performance of anchor bolts on the seismic performance of column-base plate connections, L-shaped round bars and thread bars were used as the hooked anchor bolts in the test specimens. Test results showed that bond performance of anchor bolts and the thickness of base plate significantly affect the structural performance and energy dissipation capacity. In particular, it was found that even if the requirements for minimum thickness of the base plate that is satisfied, the base plate can yield before the capacity of steel column reaches the plastic moment resulting in decreasing the structural performance of the connections. However, the proposed details of the connections might be considered as the partially restrained, that is semi-rigid connections. Consequently, the L-shaped thread anchor bolts is applicable in the exposed column-base plate weak-axis connections of small-size steel structures.

• Korean Journal of Crystallography
• /
• v.12 no.4
• /
• pp.197-206
• /
• 2001

A stoichiometric mixture of evaporating materials for AgInS₂ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films. AgInS₂ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy(HWE)system. The source and substrate temperatures were 680℃ and 410℃, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction(DCXD). The carrier density and mobility of AgInS₂ single crystal thin film mea-sured from Hall effect by van der Pauw method are 9.35×10/sup 16/㎤ and 294㎠/V·s at 293K respectively. The temperature dependence of the energy band gap of the AgInS₂ obtained from the absorption spectra was well described by the Varshni's relation , E/sub g/(T)=2.1365eV-(9.89×10/sup-3/eV/K/)T²(T+2930K). The crystal field and the spin-orbit splitting energies for the valence band of the AgInS₂ have been estimated to be 0.1541eV and 0.0129 eV, respectively, by means of the photocur-rent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the Δso definitely exists in the Γ/sub 5/ states of the valence band of the AgInS₂ /GaAs epilayer. The three photo-current peaks ovserved at 10K are ascribed to the A₁-, B-₁and C₁-exction peaks for n=1.

• Development and Reproduction
• /
• v.13 no.3
• /
• pp.183-190
• /
• 2009

In mammals, puberty is a dynamic transition process from infertile immature state to fertile adult state. The neuroendocrine aspect of puberty is started with functional activation of hypothalamus-pituitary-gonadal hormone axis. The timing of puberty can be altered by many factors including hormones and/or hormone-like materials, social cues and metabolic signals. For a long time, attainment of a particular body weight or percentage of body fat has been thought as crucial determinant of puberty onset. However, the precise effect of high-fat (HF) diet on the regulation of hypothalamic GnRH neuron during prepubertal period has not been fully elucidated yet. The present study was undertaken to test the effect of a HF diet on the puberty onset and hypothalamic gene expressions in immature female rats. The HF diet (45% energy from fat, HF group) was applied to female rats from weaning to around puberty onset (postnatal days, PND 22-40). Body weight and vaginal opening (VO) were checked daily during the entire feeding period. In the second experiment, all animals were sacrificed on PND 36 to measure the weights of reproductive tissues. Histological studies were performed to assess the effect of HF diet feeding on the structural alterations in the reproductive tissues. To determine the transcriptional changes of reproductive hormone-related genes in hypothalamus, total RNAs were extracted and applied to the semi-quantitative reverse transcription polymerase chain reaction (RT-PCR). Body weights of HF group animals tend to be higher than those of control animals between PND 22 and PND 31, and significant differences were observed PND 32, PND 34, PND 35 and PND 36 (p<0.05). Advanced VO was shown in the HF group (PND $32.8{\pm}0.37$ p<0.001) compared to the control (PND $38.25{\pm}0.25$). The weight of ovaries (p<0.01) and uteri (p<0.05) from HF group animals significantly increased when compared to those from control animals. Corpora lutea were observed in the ovaries from the HF group animals but not in control ovaries. Similarly, hypertrophy of luminal and glandular uterine epithelia was found only in the HF group animals. In the semi-quantitative RT-PCR studies, the transcriptional activities of KiSS-1 in HF group animals were significantly higher than those from the control animals (p<0.001). Likewise, the mRNA levels of GnRH (p<0.05) were significantly elevated in HF group animals. The present study indicated that the feeding HF diet during the post-weaning period activates the upstream modulators of gonadotropin such as GnRH and KiSS-1 in hypothalamus, resulting early onset of puberty in immature female rats.

• Geophysics and Geophysical Exploration
• /
• v.11 no.2
• /
• pp.153-160
• /
• 2008

Seismic modeling is used to simulate wave propagation in the earth. Although the earth's subsurface is usually semi-infinite, we cannot handle the semi-infinite model in seismic modeling because of limited computational resources. For this reason, we usually assume a finite-sized model in seismic modeling. In that case, we need to eliminate the edge reflections arising from the artificial boundaries introducing a proper boundary condition. In this study, we changed three kinds of boundary conditions (sponge boundary condition, Clayton and Engquist's absorbing boundary condition, and Higdon's transparent boundary condition) so that they can be applied in elastic wave modeling for anisotropic media. We then apply them to several models whose Poisson's ratios are different. Clayton and Engquist's absorbing boundary condition is unstable in both isotropic and anisotropic media, when Poisson's ratio is large. This indicates that the absorbing boundary condition can be applied in anisotropic media restrictively. Although the sponge boundary condition yields good results for both isotropic and anisotropic media, it requires too much computational memory and time. On the other hand, Higdon's transparent boundary condition is not only inexpensive, but also reduce reflections over a wide range of incident angles. We think that Higdon's transparent boundary condition can be a method of choice for anisotropic media, where Poisson's ratio is large.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.293-302
• /
• 1991

The anomalous sea level deviation or storm surge caused by the typhoon Thelma in 1987 are studied analysing tidal observation data at 7 stations in the south coast of Korean peninsula. The surges are calculated by subtracting the predicted tidal height from the observed tidal record. The tidal deviation at these stations along the coast are discussed in association with meteorological data. The sea level anomalies are studied by means of the empirical orthogonal function (EOF) analysis and the fast fourier transform (FFT) method. The results of analysis suggest that the peak value of surges are higher at the tidal stations in semi-enclosed bay and in long narrow channel than at the ones facing with the open sea. From the result of EOF analysis, the temporal and spatial fluctuations of storm surge can be described by the first EOF mode, which explains 63% of the total variances during the passage of typhoon Thelma. The deviation of storm surge in the studied areas indicates bi-modal peak during the passage of typhoon Thelma. From the results of FFT spectrum analysis, the peak of energy of autospectrum for surge, atmospheric pressure, and wind stress appeared at low frequency fluctuations band of 0.008-0.076 cph over the 4 stations. Auto-correlation function of surge showed periodicity, while that of atmospheric pressure and wind stress indicates no periodicity. The result of FFT analysis shows that the typhoon surges are related chiefly with the change of atmospheric pressure in an open bay (Cheju Harbor), but with the wind stress in a semi-enclosed bay (Yeosu Harbor).

• Polymer(Korea)
• /
• v.38 no.1
• /
• pp.31-37
• /
• 2014

To prepare biomass based nylon 6,5 copolymers, ${\varepsilon}$-caprolactam and 2-piperidone, the monomers of nylon 6,5 copolymers, were synthesized respectively from lysine and 5-aminovaleric acid which were produced from glucose by the fermentation process. The copolymers were then polymerized by the anionic ring opening polymerization of them at $40^{\circ}C$, using potassium tert-butoxide as a catalyst and acetyl-2-caprolactam and carbon dioxide as initiators. The prepared copolymers were characterized with various analytical methods: their viscosity molecular weight ($M_{\eta}$) was as high as 30000 g/mol and polymerization yield was over 50%, and it was found that they were semi-crystalline polymers having melting point at $165^{\circ}C$ which was much lower than its thermal degradation point, $250^{\circ}C$. These polymers were expected to have good thermal processability and application fields.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.4
• /
• pp.10-39
• /
• 1988

This study investigated the temperatures and relative humidities in the semi-greenhouse type solar dryer with a black rock-bed heat storage and without heat storage and outdoor temperature and relative humidity at 9 a.m. and 2 p.m.. A comparison was made of the drying rates, final moisture contents, moisture content distributions, casehardening stresses, drying defects, volumetric shrinkage of dried lumber for solar- and air-drying from the green condition of mixtures of Douglas-fir, lauan, taun, oak and sycamore 25mm- and 50 mm-thick lumber during the same period for four seasons, and heat efficiencies for solar dryer with and without the heat storage for saving of heat energy and the cost of lumber drying using the solar energy. The results from this study were summarized as follows: I. The mean weekly temperatures in the solar dryers were 3 to $6^{\circ}C$ at 9 a.m. and 9 to $13^{\circ}C$ at 2 p.m. higher than mean outdoor temperature during all the drying period. 2. The mean weekly relative humidities in the solar dryers were about 1 to 19% at 9 a.m. higher than the outdoor relative humidity. and the difference between indoor and outdoor relative humidity in the morning was greater than in the afternoon. 3. The temperatures and relative humidities in the solar dryer with and without the heat storage were nearly same. 4. The overall solar insolation during the spring months was highest and then was greater in the order of summer, atumm, and winter month. S. The initial rate of solar drying was more rapid than that of air drying. As moisture content decreased, solar drying rate became more rapid than that of air drying. The rates of solar drying with and without heat storage were nearly same. The drying rate of Douglas-fir was fastest and then faster in the order of sycamore, lauan, taun and oak. and the faster drying rate of species, the smaller differences of drying rates between thicknesses of lumber. The drying rates were fastest in the summer and slowest in the winter. The rates of solar drying during the spring were more slowly in the early stage and faster in the later stage than those during the autumn. 6. The final moisture contents were above 15% for 25mm-thick air dried and about 10% for solar dried lumber, but the mean final MCs for 50mm-thick lumber were much higher than those of thin lumber. The differences of final MC between upper and lower course of pile for solar drying were greater than those of pile for air drying. The differences of moisture content between the shell and the core of air dried lumbers were greater than those of solar dried lumber, smallest in the drying during summer and greatest in the drying during winter among seasons. 7. Casehardening stresses of 25mm- and 50mm-thick dried lumber were slight, casehardening stress of solar dried lumber was severer than that of air dried lumber and was similar between solar dried lumber with and without heat storage, Casehardening stresses of lumber dried during spring were slightest and then slighter in the order of summer, autumn, and winter. Casehardening stresses of Douglas -fir, sycamore and lauan were slight, comparing with those of taun and oak. 8. Maximum initial checks of 25mm-thick lumber occurred above and below fiber saturation point and those of 50mm-thick lumber occurred in the higher moisture content than thin lumber. As the moisture content decreased, most of checks were closed and didn't show distinct difference of the degree of checks among drying methods. The degree of checks were very slight in case of Douglas-fir and lauan, and severe in case of taun and oak. The degree of checks for 50mm-thick lumber were severer than those for 25mm-thick lumber. 9. The degree of warpage showed severe in case of oak and sycamore lumber, but no warping was found in case of Douglas-fir, lauan and taun. 10. The volumetric shrinkages of taun and oak were large and medium in case of Douglas-fir, lauan and sycamore. 11. Heat efficiencies of solar dryer with heat storage were 6.9% during spring, 7.7% during summer, 12.1% during autumn and 4.1% during winter season. Heat efficiency of solar dryer with heat storage was slightly greater than that of without heat storage. As moisture content of lumber decreased, heat efficiency decreased.

• Journal of Radiation Protection and Research
• /
• v.24 no.2
• /
• pp.87-92
• /
• 1999

The present study was carried out to evaluate the morphological changes in the degenerating primordial follicles induced by $\gamma$-radiation. The prepubertal female mice of three weeks old ICR strain were whole-body irradiated with a dose of $LD_{80(30)}$ (8.3 Gy). The ovaries were collected at 0 h, 3 h, 6 h, and 12 h post-irradiation. The largest cross sections were prepared with histological semi-thin sections and then observed microscopically. The ratio of normal to atretic follicles was reduced significantly after 6th post-irradiation. At 6 h post-irradiation, the number of degenerated primordial follicles increased. Germinal vesicles disappeared, and lipid droplets increased. No more ooplasmic membranes were seen. Granulosa cells became round in shape, and apoptotic cells started to appear. The ratio of normal to atretic follicles in the control group was 62.50%. The ratio decreased with time after irradiation. The ratio decreased down to 51.61 %, 48.97 %, 11.11 %, and 7.14 % at 0 h, 3 h, 6 h, and 12 h, respectively. Taken together, ionizing radiation acutely induced the degeneration of primordial follicles. The patterns of degeneration are 1) apoptosis of one or more granulosa cells with relatively intact oocyte, 2) apoptosis of oocyte with intact follicle cells, or 3) apoptotic degenerations of both cells. The Present study can provide morphological clues for the identification of degenerating primordial follicles.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.3
• /
• pp.376-380
• /
• 2006

An experiment was conducted to study the effect of temperature and pH on in vitro nutrient degradability, volatile fatty acid profile and methane production. The fermenter used was the semi-continuous system, known as the rumen simulation technique (RUSITEC). Sixteen cylinders were used at one time with a volume of 800 ml, the dilution rate was set at 3.5%/hour, the infused buffer being McDougall's artificial saliva. Basal diet (9.6 g DM) used in RUSITEC consisted of (DM) 6.40 g Timothy hay, 1.86 g crushed corn and 1.34 g soybean meal. The food for the fermentation vessel was provided in nylon bags, which were gently agitated in the liquid phase. The experiment lasted for 17 d with all the samples taken during the last 5 d. Treatments were allocated at random to four vessels each and were (1) two temperature levels of $39^{\circ}C$ and $41^{\circ}C$ (2) two pH levels of 6.0 and 7.0. The total diet contained ($g\;kg^{-1}$ DM) 957 OM, 115 CP and $167MJ\;kg^{-1}$ (DM) GE. Although increase in temperature from $39^{\circ}C$ to $41^{\circ}C$ reduced degradation of major nutrients in vitro, it was non-significant. Interaction effect of temperature with pH also reflected a similar trend. However, pH showed a significant (p<0.05) negative effect on the degradability of all the nutrients in vitro. Altering the in vitro pH from 7 to 6 caused marked reduction in DMD from 60.2 to 41.8, CPD from 76.3 to 55.3 and GED from 55.3 to 35.1, respectively. Low pH (6) depressed total VFA production (61.9 vs. 34.9 mM) as well as acetate to propionate ratio in vitro (from 2.0 to 1.5) when compared to pH 7. Compared to pH 7, total gas production decreased from 1,841 ml to 1,148 ml at pH 6, $CO_2$ and $CH_4$ production also reduced from 639 to 260 ml and 138 to 45 ml, respectively. This study supported the premise that pH is one of the principal factors affecting the microbial production of volatile fatty acids and gas. Regulating the ruminal pH to increase bacterial activity may be one of the methods to optimize VFA production, reduce methane and, possibly, improve animal performance.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.419-426
• /
• 1999

In this study, the reaction rate constant, activation energy, total crosslinking density, elastic constant, cure properties ($t_5,\;t_{90}$), modulus, and abrasion resistance of rubber compounds were investigated as a function of cure temperatures, cure systems and reinforcing filler loadings. Reaction rate constants showed strong dependence on thc carbon black loading, cure temperature and cure system, and increased sharply with increasing the reaction temperatures. The lowest activation energy was obtained in the efficient cure (EC) system which corresponds to the high level of sulfur to accelerator ratio, and the activation energy was decreased with decreasing the carbon black loadings. The change of carbon black loadings directly affects the modulus and abrasion resistance, but the change of cure system showed various effects on the rubber compounds. Increased carbon black loadings showed the high modulus, improved abrasion resistance and short scorch time but decrease in crosslinking density and elastic constant. Higher crosslinking density and elastic constant were shown in the EC cure system regardless of carbon black loadings, but scorch timc ($t_5$) was not affected by the change of the ratio of sulfur to accelerator. Rapid optimum cure time ($t_{90}$) were showen in the EC cure system. Also, the equivalent cure curve coefficient of rubber compound was 0.96 for conventional cure (CC) system, and 0.94 for semi-efficient cure (SEC) and EC system regardless carbon black loadings. As regarding the abrasion resistance, wear volume showed the logarithmic increase for the loaded weight.