• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.6
• /
• pp.467-473
• /
• 2003

This paper describes the fluttering characteristics of the upper pad in a tilting pad journal bearing(6-pad, LOP type) using a steam turbine. In order to investigate the phenomena of the upper pad fluttering experimentally, the absolute vibration of the upper pads, the relative vibration between bearing and shaft and the circumferential distribution of the film thickness are measured under the different values of supply oil flow rate, shaft speed and bearing load. It can be known that the fluttering mechanism of the upper pads has a tendency of the self-excited vibration from the study of fluttering frequencies and amplitudes with the change of shaft speed. Furthermore, it is observed that the incipient upper pad fluttering velocity is increased by the increase of oil supply flow rate and the fluttering amplitude of the upper pads is increased by the decrease of the ell flow rate and by the increase of the bearing load.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.202-206
• /
• 2001

Machine tool chatter is the self-excited vibration generated by chip thickness variation and severely degrades the quality of machined surface. The incidence of chatter is greatly affected by the dynamic characteristics of machine tool structure. Therefore, the cutting dynamics in the parallel machine tool is to be carefully studied considering the dynamic characteristics of parallel mechanism. In this paper, the vibration model of parallel machine tool is derived, in which the legs of the parallel mechanism are considered as spring-damper systems. The chatter stability charts for various machining parameters are examined with the example of the cubic parallel mechanism that is specially designed for machine tool use.

• Journal of Advanced Marine Engineering and Technology
• /
• v.10 no.4
• /
• pp.31-40
• /
• 1986

With the tendency toward high speed and high pressure in centrifugal pumps, the problem of sub-synchronous vibration has arisen, caused by the hydraulic forces of the working fluid, such as wearring, balance piston, impeller, etc.. These forces can drastically alter the rotor critical speeds and stability characteristics, and can be acted significant destabilizing forces. For preventing such self-excited vibration, the desing of the rotor system needs, which would secure the stability of the machine. In this paper, a procedure is presented for dynamic modeling of rotor-bearing-seal-impeller systems which consist of rigid disks, distributed parameter finite rotor elements and discrete bearings, seals and impellers. A finite element model including the effects of rotatory inertia and gyroscopic moments is developed using the consistent matrix approach. The technique of dynamic matrix reduction is applied to the shaft matrices to reduce them to a set of matrices of dynamic of significantly fewer degrees of freedom. The representation of bearing, seal and impeller elements is in term of linearized stiffness and damping matrices by reasonably small perturbations from equilibrium. The stability behavior of a typical double suction centrifugal pump is presented. Results show the influence of clearance and flow conditions on running speeds and stability characteristics.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.135-142
• /
• 1998

The performances of cutting process is mostly affected by the characteristics of closed loop system constructed with machine tool structure, work piece and tools. The chucking system is very important component in this system to hold work piece correctly in various static and dynamic load condition. Therefore, chucking force and accuracy must be considered carefully, from these reason, this paper describes the stability of chucking system which preserve high stiffness and accuracy of machine tool system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.355-357
• /
• 2014

The usefulness of unsteady combustion was experimentally investigated using confined premixed flames stabilized by a rearward-facing step. For this purpose, apparatus of forced pulsating mixture supply, which could be modulated its amplitude and frequency, was designed. The unsteady combustion used in this experiment plays an important role in controlling self-excited combustion oscillations and furthermore it exhibits desirable performance, from a practical point of view, such as high load combustion and reduction of pollutant emission like nitric oxide.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.5
• /
• pp.18-24
• /
• 1995

Drilling chatter is regenerative type self-excited vibration and can be predicted by the measurments of the dynamic compliance between tool and workpiece based on structural dynamics and cutting dynamics. This paper describes the theoretical prediction about drilling chatter and the mechanism of the formation of multi-coner shape in holes by drilling chatter. By the experiments and theoretical study, it is found that the odd number of multi-coner shape is always generated by drilling chatter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.236-240
• /
• 2005

This paper deals with friction-induced vibration of disc brake system under constact friction coefficient. A linear, finite element model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the FEM model, The comparison of experimental and analytical results shows a good agreement and the analysis indicates that mode coupling due to friction force and geometric instability is responsible fur disc brake squeal. And the Front brake system reduced the squeal noise using design of experiment method(DOE). This helped to validate the FEM model and establish confidence in the simulation results. Also they may be useful during real disk brake model.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.12
• /
• pp.903-910
• /
• 2003

A two-degree-of-freedom model is suggested to describe basic dynamical behaviors of the interaction between the pad and the disc of a disc brake system. Although a pad (and a disc) has many modes of vibration in practice, only one mode of each component Is considered. In this paper, a linear analysis is performed by means of the stability analysis to show various conditions for the system to become unstable, and is based on the assumption that the existence of limit cycle (this corresponds to an unstable equilibrium point inside the limit cycle) represents the squeal state of the disc brake system. The results of the stability analysis show that the damping of the disc is as much Important as that of the pad, whereas the damping of the pad only is considered In most practical situations.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.3
• /
• pp.281-287
• /
• 2016

The purpose of this study is to analyze the vibration characteristics and develop a mounting which can improve the strength safety factor to replace the high failure rate APU(auxiliary power unit) imported metal mounts with rubber mount that can be domestically produced. For this study, we analyzed in 3 kinds of rubber mounts hardness for the natural frequency to avoid the average excited frequency of the APU. In addition, allowed vibration acceleration of rubber mount confirmed to 90.8 g by adding a strength safety factor. To assure the validity of the design, we measure the vibration acceleration equipped with a metal mount and rubber mount 2 species(Hs 50 and 60). As a result, the proposed design method in this study is reasonable because the rubber mounts is excellent strength safety factor and vibration transmissibility than metal mounts.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.820-825
• /
• 2004

This paper deals with friction-induced vibration of disc brake system under constant friction coefficient. A linear, finite element parameter model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the FEM model, the experimental modal test and the dynamometer test are performed. The comparison of experimental and simulation results shows a good agreement and the analysis indicates that mode coupling due to friction force is responsible for disc brake squeal. And squeal type instability is investigated by using the parametric rotor simulation. This indicates parameters which have influence on the propensity of brake squeal. This helped to validate the FEM model and establish confidence in the simulation results. Also they may be useful during real disk brake model.