• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.3
• /
• pp.470-485
• /
• 1997

A fundamental principle in clasp selection for a specific abutment is the reduction of the transmission of excessive forces to the abutment tooth. Those forces include tilting, tipping, and stress on the abutment tooth. The flexibility of a clasp was believed to directly affect the reduction of such forces. Opinions have been expressed concerning the proper type of clasp to be used to prevent stress on periodontium. In order to evaluate and compare the various designs of a clasp system, it is necessary to measure these forces. This study compared the average measurements of forces required to dislodge three kinds of circumferential clasps having different amount of undercuts : the first with a round retentive arm, the second with a half round retentive arm, the third with a wrought wire retentive arm under tensile load. Three commonly used undercuts( 0.01, 0.02, 0.03 inch) were created on nine cast crowns, premolars and molars. The test was run six times for a same clasp. The means of tensile load required to dislodge each of the different clasps were compared statistically using the ANOVA test and multiple range test (Duncan test). The results were as follows. 1. The amount of tensile load of the wrought wire clasp was significantly different from the cast round or half round clasp (p<0.05). 2. The more amount of the undercut, the more tensile load was needed to dislodge the clasps. There were significant differences among them (p<0.05). 3. The molar showed higher tensile load than the premolar, and there was significant difference (p<0.05). 4. The means of tensile load according to clasp types showed significant differences at the molar between wrought wire clasp and cast clasp (p<0.05), but did not at the premolar.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.8A
• /
• pp.787-793
• /
• 2008

3GPP evolved packet system (EPS) is an all-IP based system that supports various access networks such LTE, HSPA/HSPA+, and non-3GPP networks. Recently, the support of IP flows with packet level QoS profiles was added to the requirements of the EPS. This paper proposes an adaptive modulation and coding (AMC) scheme that supports the QoS of such IP flows in the 3G LTE access network of the EPS. Defining the retransmission as a critical factor for QoS, the proposed scheme applies different maximum packet error probability $P_{max}$ to each packet when selecting the AMC transmission mode. In determining $P_{max}$, the QoS constraints and NACK-to-ACK error as well as channel condition are considered, balancing two objectives: the satisfaction of the QoS and the maximization of spectral efficiency. The simulation results show that it is able to reduce both delay violation and status report by 10%, while improving the throughput 10% in comparison with an existing scheme.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.3
• /
• pp.310-315
• /
• 2004

Image taken in the night can be low-contrast images because of poor environment and image transmission. We propose an algorithm that improves the acquired low-contrast image. MPEG-2 separates chrominance and illuminance, and compresses respectively because human vision is more sensitive to luminance. We extracted illumination and used K-means algorithm to find a proper crossover point automatically. We used K-means algorithm in the viewpoint that the problem of crossover point selection can be considered as the two-category classification problem. We divided an image into two subimages using the crossover point, and applied the histogram equalization method respectively. We used the index of fuzziness to evaluate the degree of improvement. We compare the results of the proposed method with those of other methods.

• Journal of KIISE:Databases
• /
• v.36 no.4
• /
• pp.292-305
• /
• 2009

Wireless sensor networks have a lot of application areas such as industrial process control, machine and resource management, environment and habitat monitoring. One of the main objects of using wireless sensor networks in these areas is the event detection. To detect events at a user's request, we need a join processing between sensor data and the predicates of the events. If there are too many predicates of events compared with a node's capacity, it is impossible to store them in a node and to do an in-network join with the generated sensor data This paper proposes a predicate-merge based in-network join approach to efficiently detect multiple events, considering the limited capacity of a sensor node and many predicates of events. It reduces the number of the original predicates of events by substituting some pairs of original predicates with some merged predicates. We create an estimation model of a message transmission cost and apply it to the selection algorithm of targets for merged predicates. The experiments validate the cost estimation model and show the superior performance of the proposed approach compared with the existing approaches.

• The KIPS Transactions:PartC
• /
• v.18C no.3
• /
• pp.179-186
• /
• 2011

Wireless Mesh Network technology refers to the technology which establishes wireless network whose transmission speed is similar to that of the wire system, and provides more enhanced flexibility in the building of network, compared to the existing wired network. In addition, it has the feature of less mobility and less restriction from the energy effect. However, there follow many considerations such as system overhead in the case of setting or the selection of multi-path. Accordingly, the focus is on the design and optimization of network which can reflect this network feature and the technology to establish path. This paper suggests the methods on the programming of path in Wireless Mesh Network routing by applying the evaluation value of node service, making use of the loss rate of data, the hop count of bandwidth and link and the traffic status of node, considering the performance of link and load in the fitness evaluation function, in order to respond to the programming of multi-path effectively.

• The KIPS Transactions:PartC
• /
• v.17C no.2
• /
• pp.189-196
• /
• 2010

The LEACH does not use flooding method for data transmission and this makes low power consumption. So performance of the WSN is increased. On the other hand, QoS based algorithm which use restricted flooding method in WSN also achieves low power consuming rate by reducing the number of nodes that are participated in routing path selection. But when the data is delivered to the sink node, the LEACH choose a routing path which has a small hop count. And it leads that the performance of the entire network is worse. In the paper we propose a QoS based energy efficient clustering and routing algorithm in WSN. I classify the type of packet with two classes, based on the energy efficiency that is the most important issue in WSN. We provide the differentiated services according to the different type of packet. Simulation results evaluated by the NS-2 show that proposed algorithm extended the network lifetime 2.47 times at average. And each of the case in the class 1 and class 2 data packet, the throughput is improved 312% and 61% each.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.3
• /
• pp.219-237
• /
• 2020

Rapid economic development and urban population growth have been increasing the necessity for underground space exploration and utilization due to the need of upgrading and expanding the existing infrastructures. TBM has been widely used to construct underground structures with high advance rate and minimal ground disturbance. Two important design parameters, which are available thrust capacity and cutterhead torque, should be estimated for any project in addition to proper selection of TBM type. However, the conventional thrust force and torque estimation model only depends on the empirical equation, which hinders the design process of the optimal thrust hydraulic system and the appropriate hydraulic components. In this study, four thrust and torque calculation models are derived and explained. For TBM design practice, the four estimation models are compared and discussed.

• Journal of Aerospace System Engineering
• /
• v.13 no.5
• /
• pp.87-93
• /
• 2019

This study suggests the development of the ALE (Automatic Link Establishment) system for the long-range communication with a helicopter at the lands or marines by HF (High Frequency) radios. In the condition of LOS or more than 35 NM, the communication success rate is significantly lowered when the frequency is manually selected because of the reduced transmission power and various strong RF environment noise signals. In this paper, we make an effort to overcome the difficulties of choosing the optimal frequency when the operating frequency selection is manually operated in long-distance communication or LOS uncertain environment. The ALE system is designed based on the frequency analysis propagation software and is verified that the communication success rate is increased by applying the proposed system. The ALE system was applied to the helicopter system and the ground/flight test was conducted. As a result, the superiority and efficiency of the proposed system were verified.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.11-18
• /
• 2021

The small radio frequency tracking radar is a tracking system with a radio frequency sensor that identifies a target through all-weather radio frequency signal processing for a target and searches, detects and tracks the target for the major target. In this paper, we describe the development of a board equipped with TMS320C6678 and XILINX FPGA (Field Programmable Gate Array), a high-speed multi-core DSP that acquires target information through all-weather radio frequency and identifies a target through real-time signal processing. We propose DSP-FPGA combination architecture for DSP and FPGA selection and signal processing, and also explain the design of SRIO for high-speed data transmission.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.10
• /
• pp.93-100
• /
• 2021

In this paper, the possibility of a UE (User Equipment) incarceration attack using RRCRejecet and RRCRelease in 5G SNPN (Standalone Non-Public Network) is analyzed based on the 3GPP standard document. First, the cell selection and reselection procedures of the UE are analyzed, and then the processing process of the false base station and the UE before and after transmission of RRCReject and RRCRelease is analyzed. As a result of the analysis, it is possible that the false base station that transmits a strong signal causes the victim UE to establish an RRC connection to the false base station itself. In addition, if the false base station transmits an RRCReject message without integrity protection in response to the victim UE's attempt to establish an RRC connection, it is determined that the victim UE can continue to stay in the RRC connection attempt process. On the other hand, it is determined that it is impossible to incarcerate the victim UE by inducing an attempt to establish an RRC connection to another false base station using RRCRelease.