• Bulletin of the Korean Chemical Society
• /
• v.23 no.8
• /
• pp.1078-1084
• /
• 2002

The formation temperature for the perovskite lead zirconate titanate [Pb(Zr,Ti)O3, PZT] derived from sol-gel route was lowered by more than $100^{\circ}C$ with the addition of crystallographically suitable seed particles, such as barium titanat e (BT) or PZT. We investigated the effect of seeding on the crystallization of perovskite phase and in the microstructure of the sol-gel derived PZT powder by varying the concentration, size and chemical species of seed particles. The phase transition as a function of temperature was monitored by DTA, XRD, and Raman spectroscopy, and the interface between the seed particle and grown PZT layer was analyzed by SEM and high resolution TEM techniques. It was found that both the heterogeneous and homogeneous nucleation contributes competitively in the formation of perovskite PZT grains.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.27-32
• /
• 2004

High temperature superconducting coated conductor has a structure of /< superconducting layer>//. The buffer layer consists of multi layer, and the architecture most widely used in RABiTS approach is CeO$_2$(cap layer)/YSZ(diffusion barrier layer)/CeO$_2$(seed layer). Evaporation technique is used for the CeO$_2$ layer and DC reactive sputtering technique is used for the YSZ layer, A chamber was set up specially for DC reactive sputtering, Detailed features are as following. A separator divided the chamber into two halves a sputtering chamber and a reaction chamber. The argon gas for sputtering target elements flows out of the cap of sputtering gun, and water vapor for reaction with depositing species spouts near the substrate. Turbo pump is connected with reaction chamber. High speed deposition of YSZ film could be achieved in the chamber. Detailed deposition conditions (temperature and partial pressure of reaction gas) were investigated for the rapid growth of high quality YSZ film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.6
• /
• pp.260-262
• /
• 2005

Thickness optimization of heavily doped p-type seeding layer was studied to improve performance of thin film silicon solar cell. We used liquid phase epitaxy (LPE) to grow active layer of $25{\mu}m$ thickness on $p^+$ seeding layer. The cells with $p^+$ seeding layer of $10{\mu}m\;to\;50{\mu}m$ thickness were fabricated. The highest efficiency of a cell is 12.95%, with $V_{oc}=633mV,\;J_{sc}=26.5mA/cm^2$, FF = 77.15%. The $p^+$ seeding layer of the cell is $20{\mu}m$ thick. As thicker seeding layer than $20{\mu}m$, the performance of the cell was degraded. The results demonstrate that the part of the recombination current is due to the heavily doped seeding layer. Thickness of heavily doped p-type seeding layer was optimized to $20{\mu}m$. The performance of solar cell is expected to improve with the incorporation of light trapping as texturing and AR coating.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.168-171
• /
• 2005

Thickness optimization of heavily doped p-type seeding layer was studied to improve performance of thin film silicon solar cell. We used liquid phase epitaxy (LPE) to grow active layer of $25{\MU}m$ thickness on p+ seeding layer. The cells with p+ seeding layer of $10{\mu}m\;to\;50{\mu}m$ thickness were fabricated. The highest efficiency of a cell is $12.95\%$, with Voc=633mV, $Jsc=26.5mA/cm^2,\;FF=77.15\%$. The $P^+$ seeding layer of the cell is $20{\mu}m$, thick. As thicker seeding layer than $20{\mu}m$, the performance of the cell was degraded. The results demonstrate that the part of the recombination current is due to the heavily doped seeding layer. Thickness of heavily doped p-type seeding layer was optimized to $20{\mu}m$. The performance of solar cell is expected to improve with the incorporation of light trapping as texturing and AR coating.

• Natural Product Sciences
• /
• v.8 no.3
• /
• pp.83-89
• /
• 2002

Butea monosperma Kuntze, commonly known as 'Palash', is employed in various indigenous systems of medicine against several diseases and almost every part of the plant has diversified medicinal properties. The seeds are used as anthelmintic, aperient, digesti and to treat piles, skin diseases and abdominal troubles. They also have the property of reducing 'Kapha' and 'Vata' (in Ayurveda). In the present paper a detailed pharmacognostical evaluation of seeds has been undertaken. The study includes macro- and micro-scopical details, fluorescence powder study and HPTLC fingerprinting. The seed is characterized by finely ridged seed coat and palisade-like malpighian cells, discontinuous transparent linea lucida in upper half of malpighian layer and simple & oblong hilum. The study also concludes that the seed samples procured from different places have similar morphological and physico-chemical characteristics. These observations are also supported by similar TLC profiles. The estimation of heavy metals (to detect permissible toxic limits), and fatty acid composition have been carried out. An attempt has also been made to see the ecological and edaphic variations, if any.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.267-272
• /
• 2000

Electroplating Cu was deposited on Si(100) wafer after seed Cu was deposited by sputtering first. TaN was deposited as a diffusion barrier before depositing the seed Cu. Electroplating Cu thin films show highly (111)-oriented microstructure for both before and after annealing at $450^{\circ}C$ for 30min and no copper silicide was detected in the same samples, which indicates that TaN barrier layer blocks well the Cu diffusion into silicon substrate. After annealing the electroplating Cu film up to $450^{\circ}C$, the Cu film became columnar from non-columnar, its grain size became larger about two times, and also defects density of stacking faults, twins and dislocations decreased greatly. Thus the heat treatment will improve significantly electromigration property caused by the grain boundary in the Cu thin films.

• Journal of Korean Society of Forest Science
• /
• v.86 no.3
• /
• pp.288-300
• /
• 1997

Morphology and anatomy of the fruit and seed of eight species of Rhus (Anacardiaceae) were investigated. The inflorescence of R. typhina was an apical and erect thysus, that of R. javanica was panicle. while that of the others were an axillary and pendulous panicle. Anatomical investigation of the pericarp showed that exocarp and mesocarp in R. javanica and R. typhina were integrated, but its in the others were disintegrated and uniform. In all these species, endocarp consisted of distinctly three lignified cell layers (outer, middle and inner endocarp) and crystal layers. The surface sculpturing of mature seed was variable and also contributed to understanding of species delimitation and relationships within the genus. Categorization by cluster analysis with 27 characters obtained from morphological and anatomical features of the fruit and seed resulted in two groups : R. trichocarpa - R. javanica group vs. R. ambigua - R. verniciflua - R. sylvestris - R. succedanea group. Taxonomic significance for the genus by these characters was supported by results of principal component analysis. The keys for the genus Rhus were provided using morphological and anatomical characters of the inflorescence, and fruit and seed.

• Korean Journal of Medicinal Crop Science
• /
• v.21 no.1
• /
• pp.7-19
• /
• 2013

This study was carried out to select new pelleting binder and material for seeds from Fraxinus rhynchophylla Hance and Alnus sibirica Fisch. ex Turcz. The optimum treatments of the various concentrations and species of priming agents to improve seed germination of both woody medicinal plants were also estimated. Germinability was increased when the seeds of Fraxinus rhynchophylla Hance was soaked in -1.0 MPa of PEG6000 solution at $15^{\circ}C$ for 4 days significantly, the optimum treatment for improving germination of Alnus sibirica Fisch. ex Turcz was observed when the tested seeds was soaked in 100 mM of KCl at $15^{\circ}C$ for 4 days. The influence of physical and chemical properties of pelleting solid materials, the mixture of gypsum, diatomaceous earth, dalma ceramic and vermicuolite (6:1:1:1 ratio) were found as the best pelleting materials for Fraxinus rhynchophylla Hance and Alnus sibirica Fisch. ex Turcz. seeds. To satisfy the requirements of absorption and compatibility for multi-layer seed pelleting, SGPA (Starch-grafted cross-linked polyacrylates) hydrogel was prepared using starch, acrylonitrile, ceric ammonium nitrate, nitric acid, methyl alcohol and potassium hydroxide. The resulting SGPA hydrogel showed high water absorption but not plant compatibility. It suggested that seed pelleting using pelleting materials and SGPA hydrogel (multi-layer coating) after priming agent treatment is to increase germinability and seedling growth and it can reduced irrigation labours and can also save seed.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.41-45
• /
• 2021

In this study, in order to secure the high reliability of the memristor, we adopted a patterned lithium filament seed layer as the main agent for resistive switching (RS) characteristic on the 30 nm thick ZrO₂ thin film at the device manufacturing stage. Lithium filament seed layer with a thickness of 5 nm and an area of 5 ㎛ × 5 ㎛ were formed on the ZrO₂ thin film, and various electrode areas were applied to investigate the effect of capacitance on filament type memristive behavior in the parallel memristive circuit of memristor and capacitor. The RS characteristics were measured in the samples before and after 250℃ post-annealing for lithium metal diffusion. In the case of conductive filaments formed by thermal diffusion (post-annealed sample), it was not available to control the filament by applying voltage, and the other hand, the as-deposited sample showed the reversible RS characteristics by the formation and rupture of filaments. Finally, via the comparison of the RS characteristics according to the electrode area, it was confirmed that capacitance is an important factor for the formation and rupture of filaments.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.153-156
• /
• 2003

The multi-layer oxide buffer layer for the coated conductor was deposited on biaxially textured Ni substrates using pulsed laser deposition. Oxygen partial pressure, 4％$H_2$/Ar partial pressure, and deposition temperature were deposition variables investigated to find the optimum deposition conditions. $Y_2$O$_3$seed layer was deposited epitaxially on metal substrate. The full buffer architecture of $Y_2$O$_3$/YSZ/CeO$_2$was successfully prepared on metal substrate.