• The Journal of Engineering Geology
• /
• v.28 no.3
• /
• pp.465-473
• /
• 2018

The application of singular value decomposition (SVD) filtering is examined for attenuation of the ground-roll in land seismic data. Prior to the SVD computation to seek singular values containing the highly correlatable reflection energy, processing steps such as automatic gain control, elevation and refraction statics, NMO correction, and residual statics are performed to enhance the horizontal correlationships and continuities of reflections. Optimal parameters of SVD filtering are effectively chosen with diagnostic display of inverse NMO (INMO) corrected CSP (common shot point) gather. On the field data with dispersion of ground-roll overwhelmed, continuities of reflection events are much improved by SVD filtering than f-k filtering by eliminating the ground-roll with preserving the low-frequency reflections. This is well explained in the average amplitude spectra of the f-k and SVD filtered data. The reflectors including horizontal layer of the reservoir are much clearer on the stack section, with laminated events by SVD filtering and subsequent processing steps of spiking deconvolution and time-variant spectral whitening.

• Geophysics and Geophysical Exploration
• /
• v.19 no.1
• /
• pp.11-19
• /
• 2016

Two representative residual static methods of traveltime decomposition and stack-power maximization are discussed in terms of application to land seismic data. For the model data with synthetic shot/receiver statics (time shift) applied and random noises added, continuities of reflection event are much improved by stack-power maximization method, resulting the derived time-shifts approximately equal to the synthetic statics. Optimal parameters (maximum allowable shift, correlation window, iteration number) for residual statics are effectively chosen with diagnostic displays of CSP (common shot point) stack and CRP (common receiver point) stack as well as CMP gather. In addition to removal of long-wavelength time shift by refraction statics, prior to residual statics, processing steps of f-k filter, predictive deconvolution and time variant spectral whitening are employed to attenuate noises and thereby to minimize the error during the correlation process. The reflectors including horizontal layer of reservoir are more clearly shown in the variable-density section through repicking the velocities after residual statics and inverse NMO correction.

• Journal of the Korean Mathematical Society
• /
• v.41 no.3
• /
• pp.513-533
• /
• 2004

We present the pricing and hedging method for options with general payoffs in the presence of transaction costs. The convexity of the payoff function-gamma of the options- is an important issue under transaction costs. When the payoff function is convex, Leland-style pricing and hedging method still works. However, if the payoff function is of general form, additional assumptions on the size of transaction costs or of the hedging interval are needed. We do not assume that the payoff is convex as in Leland 〔11〕 and the value of the Leland number is less (bigger) than 1 as in Hoggard et al. 〔10〕, Avellaneda and Paras 〔1〕. We focus on generally recognized asymmetry between the option sellers and buyers. We decompose an option with general payoff into difference of two options each of which has a convex payoff. This method is consistent with a scheme of separating out the seller's and buyer's position of an option. In this paper, we first present a simple linear valuation method of general payoff options, and also propose in the last section more efficient hedging scheme which costs less to hedge options.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1080-1083
• /
• 2002

In this paper, we have studied with regard to the use of lasers for modifying the surface properties of silicon in order to improve it's wettability and adhesion characteristics. Using an Nd:YAG pulse laser, the wettability and adhesion characteristics of silicon surface have been developed by an Nd:YAG pulse laser. It was found that the laser treatment of silicon surfaces modified the surface energy. In the result of wetting experiments, by the sessile drop technique using the distilled water, wetting characteristic of silicon after the laser irradiation shows a decreased value of the contact angle. In case of the laser treated silicon surface, laser direct writing of copper lines has been achieved by pyrolytic decomposition of copper formate films$(Cu(HCOO)_2{\cdot}4H_2Q)$, using a focused $Ar^+$ laser beam$(\lambda=514.5nm)$ on the silicon substrates. The deposited patterns were measured by energy dispersive X-ray(EDX), Scanning Electron Microscopy(SEM) and surface profiler($\alpha$-step) to examine the cross section of deposited copper lines and linewidth.

• ETRI Journal
• /
• v.16 no.3
• /
• pp.1-10
• /
• 1994

Undoped GaAs has been successfully grown by chemical beam epitaxy (CBE) via surface decomposition process using arsine $(AsH_3)$ and trimethylgallium (TMG). Three distinct regions of temperature-dependent growth rates were identified in the range of temperatures from 570 to $690^{\circ}C$. The growth rates were found strongly dependent on the V/III ratio between 5 and 30. The growth rate at low V/III ratio seems to be determined by arsenic produced on the surface, whereas at high V/III ratio it shows dependence on the adsorption of TMG. Hall measurement and photoluminescence (PL) analysis show that the films are all p-type and that carbon impurities are primarily responsible for the background doping. Carbon concentrations have been found to be reduced by two orders of magnitude as compared to those of epilayers grown by CBE which employs TMG and arsenic obtained from precracked $AsH_3$ in a high temperature cell. It was also found that hydrogen atoms dissociated from unprecracked $AsH_3$ play an important role in removing hydrocarbon-containing species resulting in a significant reduction of car-bon impurities.

• Structural Engineering and Mechanics
• /
• v.50 no.2
• /
• pp.137-149
• /
• 2014

In this study, modal parameters such as natural frequencies, mode shapes and damping ratios of RC frames with low strength are determined for different construction stages using ambient vibration test. For this purpose full scaled, one bay and one story RC frames are produced and tested for plane, brick in-filled and brick in-filled with plaster conditions. Measurement time, frequency span and effective mode number are determined by considering similar studies and literature. To obtain experimental dynamic characteristics, Enhanced Frequency Domain Decomposition and Stochastic Subspace Identification techniques are used together. It is shown that the ambient vibration measurements are enough to identify the most significant modes of RC frames. The results indicate that modal parameters change significantly depending on the construction stages. In addition, Infill walls increase stiffness and change the mode shapes of the RC frame. There is a good agreement between mode shapes obtained from brick in-filled and in-filled with plaster conditions. However, some differences are seen in plane frame, like expected. Dynamic characteristics should be verified using finite element analysis. Finally, inconsistency between experimental and analytical dynamic characteristics should be minimize by finite element model updating using some uncertain parameters such as material properties, boundary condition and section properties to reflect the current behavior of the RC frames.

• Journal of the Korean Solar Energy Society
• /
• v.36 no.3
• /
• pp.9-16
• /
• 2016

This paper discusses a refined model for investigating the micro-mechanical behavior of beam-like structures, which are composed of various elastic moduli and complex geometries varying through the cross-section directions and are also periodically-repeated and heterogeneous along the axial direction. Following the previous work (Lee and Yu, 2011), the original three-dimensional static problem is first formulated in a unified and compact form using the concept of decomposition of the rotation tensor. Taking advantage of the smallness of the cross-sectional dimension-to-length parameter and the micro-to-macro heterogeneity, while also performing homogenization along the dimensional reduction simultaneously, the variational asymptotic method is rigorously used to construct a total energy function, which is asymptotically correct up to the second order. Furthermore, through the transformation procedure based on the pure kinematic relations and the linearized equilibrium equations, a generalized Timoshenko model is systematically established. For the purpose of dealing with realistic and complex geometries and constituent materials at the microscopic level, this present approach is incorporated into a commercial analysis package. A few examples available in literature are used to demonstrate the consistency and efficiency of this proposed model, especially for the structures, in which the effects of transverse shear deformations are significant.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.3
• /
• pp.453-462
• /
• 2002

Discrete-sizing or standardized steel profiles are used in steel design and construction practice. However, most of numerical optimization methods follow additional step(round-up discrete-sizing routine) to use the standardized steel section profiles, and accordingly the optimality of the resulting design nay be doubtful. Thus, in this paper, an efficient multi-level optimization algorithm is proposed to improve the shortcoming of the conventional optimization methods using the round-up discrete-sizing routine. Also, multi-level optimization technique with a decomposition method that separates both system-level and element-level is incorporated in the algorithm to enhance the performance of the proposed algorithms. The proposed algorithm is expected to achieve considerable improvement on both the efficiency of the numerical process and the accuracy of the global optimum.

• Journal of the Korean Society of Visualization
• /
• v.19 no.3
• /
• pp.92-98
• /
• 2021

Large Eddy Simulation (LES) has been popularly applied and used in the last several decades to simulate turbulent boundary layer in the numerical domain. A fully developed turbulent boundary layer has also been applied to predict the complicated wake flow behind bluff bodies. In this study we aimed to generate an artificial turbulent boundary layer, which is based on an exponential correlation function, and generates a series of realistic three-dimensional velocity data in two-dimensional inlet section which are correlated both in space and in time. The results suggest its excellent capability for high Reynolds number flows. To make an effective generation, a hexahedral mesh has been used and Cholesky decomposition was applied to possess suitable turbulent statistics such as the randomness and correlation of turbulent flow. As a result, the flow characteristics in the domain and fluctuating pressure near the wall are very close to those of fully developed turbulent boundary layers.

• Composites Research
• /
• v.28 no.4
• /
• pp.168-175
• /
• 2015

Recently, the applications of carbon fiber reinforced plastics (CFRPs) have become broader than ever when it comes to such industries as automotive, ships, aerospace and military because of their lightweight-ness and high mechanical properties. Thermosetting plastics like epoxy are frequently used as the binding matrix in CFRPs due to their high hardness, wetting characteristics and low viscosity. However, they cannot melted and remolded. For this reason, thermosetting plastic wastes have caused serious environmental problems with the production of fiber reinforced plastics. Thus, many studies have focused on the carbon fiber reinforced thermoplastics (CFRTPs) and recycling carbon fiber. In this study, recycled carbon fiber (RCF) was prepared from CFRPs using a pyrolysis method, which was employed to separate resin and carbon fiber. The degree of decomposition for epoxy resin was confirmed from thermal gravimetric analysis (TGA) and scanning electron microscope (SEM). The RCF was cut and ground to prepare a carbon fiber composite sheet (CFCS). CFCS was manufactured by applying recycled carbon fibers and various thermoplastic fibers. Various characterizations were performed, including morphological analyses of surface and cross-section, mechanical properties, and crystallization enthalpy of CFCS at different cooling conditions.