• 설비공학논문집
• /
• 제21권4호
• /
• pp.229-235
• /
• 2009

In a domestic construction field, floor surface must be covered not to be scratched and polluted by protector until resident comes in. However this protector restricts the contaminant to leave from floor surface. So when the protector is removed, much contaminant is emitted from the floor surface to inside and makes a bad influence on the indoor air quality, In this research, it will be tested the reduction performance of contaminant between a normal protector and a contaminant absorption protector using charcoal powder.

• Tribology and Lubricants
• /
• 제27권5호
• /
• pp.269-274
• /
• 2011

The purpose of this paper is to study and analyze the improvement method for the failure examples including the vehicle brake system in actual field. It was verified that the indicator plate of pad wear scratched the brake disk because of wearing after displacement of non- identification parts pad. The caliper of other vehicle was installed with brake system verified the phenomenon produced groove in center point because of one side wear when the pad was not fully contacted with the rub disk by other action surface pressure and pad action condition. It verified that the crack phenomenon fatigue was produced by brake thermal deformation because of decreasing the thickness by grinding to modify the non-uniformed wear of brake disk. It verified that the friction sound was produced by the friction phenomenon because of non-uniformed contact of lining and an alien substance with inner of the drum and lining braking by crack phenomenon with brake drum surface.

• Corrosion Science and Technology
• /
• 제3권1호
• /
• pp.20-25
• /
• 2004

In order to clarify the durability of protective coatings for maritime steel structures, various anti-corrosive organic coated steel samples were exposed for twelve years in semitropical marine environment at Miyakojima Island, Okinawa, JAPAN. Samples were various organic coated steel pipes, 4.0 m in length and 150 mm in diameter. While the bare steel pipe entirely corroded in 4.5 mm thickness in four and half years, these organic coated steel pipes exhibited protective appearances after twelve-year-exposure except for the defect in the coatings. Polyethylene (PE) lining pipe exhibited a good protective performance. Urethane painted pipe was also good but some barnacles stuck to its surface. A combination of petrolatum tape and FRP cover showed sufficient corrosion resistance for steel surface. The correlation in results between exposure and laboratory acceleration test was examined. It was found that salt spray test (SST) results corresponded to rusted area of scratched portion and that adhesion change of coating layer corresponded to the rotating immersion test result. Among the on-site measured data, volume resistivity is utilized for the index of corrosion protection performance of organic coating.

• 한국표면공학회지
• /
• 제50권3호
• /
• pp.183-191
• /
• 2017

In this study, surface morphology and mechanical property of TiN and DLC coated pedicle screw have been investigated by field-emission scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, vickers hardness test, axial gripping, and axial torsional gripping capacity test. From the EDS and XRD results, the composition and crystal structure of TiN and DLC coated surface were verified. The hardness value was increased by TIN and DLC coating, and the DLC coating surface has the highest value. The gripping capacity also showed higher value for TiN and DLC coated specimen than that of non-coated (Ti alloy) surface. The surface morphology of gripping tested specimen showed rougher scratched surface from Ti alloy than TiN and DLC coated layer.

• 한국세라믹학회지
• /
• 제29권12호
• /
• pp.926-934
• /
• 1992

Uniform diamond films in a few $\textrm{mm}^2$ size and locally isolated diamond single crystals in size of 60 $\mu\textrm{m}$ were synthesized on Si-wafer and Al2O3 substrate by the method of acetylene flame. The effects of substrate temperature and flow ratio of oxygen to acetylene on the morphology of deposited diamond were investigated. According to the observations of growth behavior of diamond on Si substrate with respect to substrate surface pretreatment and flow ratio, it was shown that well faceted diamonds could grow uniformly when flow ratio was above 0.9 and substrates were densely scratched. With increasing substrates temperature, the crystal morphology changes from octahedron bounded by only {111} plane below 850$^{\circ}C$ to cubo-octahedron with almost equal development of {111} and {100} plane in the temperature range of 850∼950$^{\circ}C$. Between 950∼1050$^{\circ}C$, the {111} faces become rough and concave. Above 1050$^{\circ}C$, new crystallites begin to grow on concave {111} surface and overall morphology looks like cubo-octahedron with degenerated {111} faces. These changes of morphology can be understood in terms of the different growth mode of each crystallographic plane with respect to the substrate temperature and supersaturation. And the observed phenomena on {111} planes can be related to the face instability and twin generation.

• 대한기계학회논문집A
• /
• 제26권3호
• /
• pp.537-543
• /
• 2002

This paper examines a new in-process measurement system for the measurement of micro-defects on the surfaces of brittle materials by using the AFM (Atomic Force Microscopy). A new AFM scanning stage that can also perform nano-scale bending of the sample was developed by adding a bending unit to a commercially available AFM scanner. The bending unit consists of a PZT actuator and sample holder, and can perform static and cyclic three-point bending. The true bending displacement of the bending unit is approximately 1.8mm when 80 volts are applied to the PZT actuator. The frequency response of the bending unit and the stress on the sample were also analyzed, both theoretically and experimentally. Potential surface defects of the sample were successfully detected by this measurement system. It was confirmed that the number of micro-defects on a scratched surface increases when the surface is subjected to a cyclic bending load.

• 한국산업정보학회논문지
• /
• 제11권4호
• /
• pp.66-71
• /
• 2006

본 논문에서는 DC 플라즈마와 금속유기물을 사용하여 CNF의 저온 합성에 성공하였다. 합성된 CNTs는 기판의 위치에 따라 매우 다른 특성 차이가 보였다. CNT는 일반적으로 직경 100 nm, 길이 $10{\mu}m$의 특성을 가진다. CNT의 형태적 특성들은 전계전자방출특성에 큰 영향을 준다는 사실을 본 연구를 통해 알 수 있었다. 따라서 CNF의 합성에 의한 CNF 구조적 특성은 전자소자응용면에서 매우 중요한 역할을 한다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.215-220
• /
• 2004

Molecular Dynamics(MD) method was used to investigate the change of friction force due to interaction between dislocations and a grain boundary when a Ni tip was scratched on a Cu bicrystal. The substrate comprised a Cu bicrystal containing a vertical$\Sigma=5(210)$ grain boundary. The moving tip for scratching simulation was consisted of fixed Ni atoms emulating a rigid tip. The indentation depth was $3.6\AA$ and the scratching was performed along <110>direction in the first grain. As the scratching was continued, nucleation and propagation of dislocations were observed. In the early stage, the grain boundary played as a barrier to moving dislocations and interrupting further dislocation movement with no dislocation resulting in no propagation across the grain boundary. As the Ni tip approached the grain boundary, dislocations were nucleated at the grain boundary and propagated to the second grain. However, stick-slip phenomena that were observed on a single crystal scratching were not observed in the bicrystal. And, instead, irregular oscillation of friction force was observed during the scratching due to the presence of a grain boundary.

• Computers and Concrete
• /
• 제17권2호
• /
• pp.271-280
• /
• 2016

This study examined the mechanical properties and adiabatic temperature rise of low-heat concrete developed based on ternary blended cement using ASTM type IV (LHC) cement, ground fly ash (GFA) and limestone powder (LSP). To enhance reactivity of fly ash, especially at an early age, the grassy membrane was scratched through the additional vibrator milling process. The targeted 28-day strength of concrete was selected to be 42 MPa for application to high-strength mass concrete including nuclear plant structures. The concrete mixes prepared were cured under the isothermal conditions of $5^{\circ}C$, $20^{\circ}C$, and $40^{\circ}C$. Most concrete specimens gained a relatively high strength exceeding 10 MPa at an early age, achieving the targeted 28-day strength. All concrete specimens had higher moduli of elasticity and rupture than the predictions using ACI 318-11 equations, regardless of the curing temperature. The peak temperature rise and the ascending rate of the adiabatic temperature curve measured from the prepared concrete mixes were lower by 12% and 32%, respectively, in average than those of the control specimen made using 80% ordinary Portland cement and 20% conventional fly ash.

• 한국염색가공학회지
• /
• 제22권1호
• /
• pp.51-60
• /
• 2010

This research works on the effects of drawing conditions on the physical properties of the drawn worsted yarns. The drawn worsted yarns were made by the yarn drawing system under various drawing conditions such as concentration of reducing agent, draw ratio, setting time of drawn yarn, and concentration of oxidizing agent. The drawn worsted yarns from 2/80Nm to 2/90Nm were obtained from 2/60Nm worsted yarns, the surface and cross-sectional shapes and tensile properties of these various specimens were measured and discussed with the various drawing conditions. The drawing of worsted yarn made constituent wool fiber scratched and made it changing to polygonal cross-sectional shape. The tenacity and modulus were increased with draw ratio and concentration of reducing agent. And tensile strain was increased with draw ratio, which decreased with concentration of reducing agent.