• 한국공작기계학회논문집
• /
• 제15권6호
• /
• pp.22-31
• /
• 2006

When ironwork, especially steel roll coil, is transported to customers, land transportation and sea transportation are usually used. To transport steel roll coil fast and safe without damaging it, it is necessary that the steel roll coil has to be in stable condition. These days, apitong, which is all imported from overseas, is being used to support the steel roll coil, but because of apitong's rigidity, it damages the coil and when the coil is damaged, it is hard to fix. Due to the fact that recovering damage of the coil is almost impossible, we have to find the new type of dunnage that can substitute the apitong. In this paper, the arrays and the kinds of reinforcements, and rectangular type and trapezoid of dunnage will be talked about. The phenomenon of rolling and the impact when the carrier start moving and stop will be talked about as well. Therefore, we are going to develop a dunnage that does not damage ironwork and has better recovery and softness than existing apitong dunnage.

• 한국환경보건학회지
• /
• 제13권1호
• /
• pp.17-33
• /
• 1987

As a result of technical advances and industrialization, the characteristics of domestic and industrial wastes are becoming more complex. Accordingly, improved treatment and disposal systems are being continuously sought to take account of complex characteristics and to comply with economic restrictions. In this study, an application of pyrolysis to the treatment of industrial wastes, including waste scrap rubber, waste raw material used in making the slipper bottom and waste PVC pipe, and the effectiveness of pyrolysis in resource recovery from these wastes were investigated. Batches of wastes were pyrolysed by external heating to a temperature of 400-800$\circ$C in a 32 mm diameter x 0.9 m long silica tube to produce combustible gases, oils and chars. Before the start of pyrolysis runs, the entire system was purged with nitrogen gas to exclude the air. The temperature inside the retort was controlled by the thermocouple in the gas stream, and referred to as the pyrolysis temperature. Under these conditions three products were separately collected and further analyzed. The results were summarized as follows. 1. More gases and less chars were produced with higher pyrolyzing temperature and with higher rates of heating, but the yields of oils tended downwards at temperatures above 700$\circ$C. Accordingly, operating conditions of pyrolysis should be varied with desired material. 2. Calorific values and sulfur contents of produced oils were sufficient and suitable for fuel use. Chars from waste rubber had high heating values with low sulfur contents, but calorific values of chars from waste PVC and waste slipper were as low as 3, 065-4, 273 kcal/kg and 942-2, 545 kcal/kg, respectively. Therefore, char from these wastes are inappropriate for fuel. 3. Soluble contents of Pb, Cd, Cu and Zn in chars from waste rubber and waste slipper were below the Specific Hazardous Waste Treatment Standards. However soluble contents of Pb and Cd in chars from waste PVC were one or two times and five or seven times exceedingly the Specific Hazardous Waste Treatment Standards, respectively. 4. Post high heating is desirable for treatment method of waste PVC which generates toxic hydrogen chloride. 5. The proportions of hydrogen, methane and ethane in produced gases were in the range of 3.99-35.61% V/V, 18.22-32.50% V/V and 5.17-5.87% V/V, respectively. 6. Pyrolysis is a useful disposal method in case of waste slipper, which was hardly combustible, and thus investigations of this kind of materials are required for effective management of industrial waste. 7. Based upon the possible market development for products, overall pyroly economics to take account of treatment values of noncombustible or hazardous materials should be evaluated.

• Elastomers and Composites
• /
• 제41권2호
• /
• pp.97-107
• /
• 2006

폐타이어와 폐수지 처리 문제를 해결하기 위한 방법으로 재생 폴리에틸렌 수지와 신재HDPE를 폐타이어 분말(GWTP)과 치합형 동방향 회전 이축 압출기(Fuly Intermeshing Co-rotating Twin Screw Extruder)를 이용하여 각 조성별로 용융 훈련하여 재생 PE/폐타이어 복합체를 제조하였다. 본 연구에서는 플라스틱 수지 (재생 PE, HDPE)와 폐타이어 분말의 혼합비를 $0\sim50$wt.%로 하였으며, ASTM에 의거하여 인장강도, 파단신율, 충격강도 등의 물성 변화를 확인하였다. 폐타이어 분말 함량이 증가할수록 인장강도가 감소하고 파단신율이 증가하였다. 한편 충격강도는 폐타이어 분말 함량이 30 wt.%일 때 최대이고, 함량이 증가할수록 충격 강도가 감소하는 경향을 나타내었다. 형태학적 고찰에서는 폐타이어 분말의 함량의 증가함에 따라 파단면이 거칠어지는 형상을 관찰하였다. 모세관점도계(Capillary Rheometer)를 이용하여 재생 PE/폐타이어 분말 복합체의 전단속도의 변화에 따른 용융전단점도의 변화와 연화점 (Ts) 등의 유변학적 성질을 분석한 결과, 폐타이어 분말 함량 증가에 따라 외부 응력에 대한 흐름 저항성을 증가시켜 용융점도가 상승하는 결과를 보였으며 측정된 전단율에서 전단 점도는 Power-law 거동을 보였다.

• 청정기술
• /
• 제15권3호
• /
• pp.172-179
• /
• 2009

높은 강도, 경도, 신율, 비중 및 내마모성 등을 가진 채 폐기되는 열가소성 폴리우레탄 스크랩(TPU-S)과 습윤 상태의 내슬립성은 높으나 기계적 물성이 떨어지는 EPDM 고무의 용융 블렌드를 통해 신발 소재용 필름을 제조하고 조성과 특성과의 관계를 연구하였다. 블렌드 중의 TPU-S의 함량이 증가함에 따라 강도, 신도, 내마모성, 비중 및 경도 등 모든 물성이 증가하였으나, 습윤 상태의 내슬립성(동적마찰계수)은 크게 감소하였다. TPU-S 함량의 증가에 따라 블렌드의 파단신율은 단순혼합법칙 이상으로 증가하였으며, 습윤 상태의 내슬립성은 TPU-S가 $0{\sim}65%$ 범위에서 단순혼합법칙 이상이었다. 그러나 인장강도, 비중 및 내마모성은 모두 단순혼합법칙보다 낮은 값을 나타내었다. 이들 블렌드의 조성-특성 관계의 결과로부터 일반적으로 요구되는 신발 겉창용 소재의 물성에 충족되는 EPDM/TPU-S 블렌드의 조성은 무게비가 30/70인 것을 알 수 있었다.