• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.1
• /
• pp.1-13
• /
• 2010

A comparative study between a computation and an experiment has been conducted to predict the performance of a Pod type waterjet for cm amphibious wheeled vehicle. The Pod type waterjet has been chosen on the basis of the required specific speed of more than 2500. As the Pod type waterjet is an extreme type of axial flow type waterjet, theoretical as well as experimental works about Pod type waterjets are very rare. The main purpose of the present study is to validate and compare to the experimental results of the Pod type waterjet with the developed CFD in-house code based on the RANS equations. The developed code has been validated by comparing with the experimental results of the well-known turbine problem. The validation also extended to the flush type waterjet where the pressures along the duct surface and also velocities at nozzle area have been compared with experimental results. The Pod type waterjet has been designed and the performance of the designed waterjet system including duct, impeller and stator was analyzed by the previously mentioned m-house CFD Code. The pressure distributions and limiting streamlines on the blade surfaces were computed to confirm the performance of the designed waterjets. In addition, the torque and momentum were computed to find the entire efficiency and these were compared with the model test results. Measurements were taken of the flow rate at the nozzle exit, static pressure at the various sections along the duct and also the nozzle, revolution of the impeller, torque, thrust and towing forces at various advance speed's for the prediction of performance as well as for comparison with the computations. Based on these measurements, the performance was analyzed according to the ITTC96 standard analysis method. The full-scale effective and the delivered power of the wheeled vehicle were estimated for the prediction of the service speed. This paper emphasizes the confirmation of the ITTC96 analysis method and the developed analysis code for the design and analysis of the Pod type waterjet system.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.7
• /
• pp.55-65
• /
• 2012

Total reduction factor that is used when calculating allowable tensile strength of geogrids is made by multiplying the installation damage reduction factor ($RF_{ID}$), chemical degradation reduction factor ($RF_D$), and creep reduction factor ($RF_{CR}$) etc. In case of a model estimating allowable tensile strength considering reduction factor over the short-term tensile strength of geogrids, it has a limit of not considering interaction force between reduction factors. Junction strength comes to be reduced by installation damages or chemical degradation in the same way as tensile strength. Single junction test method cannot properly test damaged samples and shows large deviations as it does not consider scale effect. Besides, regarding calculating shear strength, no reasonable study on reduction factors was conducted yet. Therefore, in this study, reduction factors that may affect the long-term performance of geogrids were revaluated considering various conditions and accurate long-term allowable tensile strength was calculated considering interrelation between reduction factors. Creep results after installation damage and chemical resistance test showed lower value than calculated value according to GRI GG-4. After the installation damage test and the chemical resistance test, the reduction factor of junction strength was less than that of tensile strength. Shear strength before and after installation damage showed no change or increase.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.10
• /
• pp.694-701
• /
• 2012

The main purpose of this study is to evaluate of backwash system of hydrodynamic separator filter (HSF) with solar powered submerged pumps. It consists of a photovoltaic solar array, control electronics, battery, and two submersible pump powered by a 12 voltage DC motor. The laboratory scale study on treatable potential of micro particles using backwash HSF that was a combined with perlite filter cartridge and backwash nozzles. Since it was not easy to use actual storm water in the scaled-down hydraulic model investigations, it was necessary to reproduce ranges of particle sizes with synthetic materials. The synthesized storm runoff was made with water and addition of particles; ion exchange resin partices, silica gel particles, and commercial area manhole sediment particles. HSF was made of acryl resin with 250 mm of diameter filter chamber and overall height of 800 mm. Four case test were performed with different backwashing conditions and determined the SS removal efficiency with various surface loading rates. The operated range of surface loading rate was about 308~$1,250m^3/m^2/day$. It was found that SS removal efficiency of HSF using two submersible pumps improved by about 18% compared with HSF without backwash. Nonpoint control devices with solar water pumping systems would be useful for backwashing the filter in areas with not suppling electricity and reduce filter media exchange cost.

• Explosives and Blasting
• /
• v.30 no.2
• /
• pp.86-97
• /
• 2012

Ground vibration induced by a bench blasting in the construction site should cause the damage to the structure and indirect damage to a human body, and the vibration level is most practical descriptor for regulating the damage to human body and peak particle velocity is the descriptor for direct damage assesment of the structure. Meantime, the vibration level has not been considered for the blasting design but this study is the case that apply not only peak particle velocity but also vibration level on the blasting design. Also, we strongly believe that this study will be helpful for the management in the blasting site which some civil appeal is concerned. Total 232 measurements of both ppv and vibration level was used to estimate the scale distance. When the regulating threshold was ppv 0.3 cm/s and vibration level 75 decibel, the charge per delay to be estimated with vibration level could be recommended by 1.2~1.4 times than it of ppv. So, it is proven that considering vibration level on the blasting design is reasonable for not only prevention of the civil appeals but also effective blasting. Again, the blasting design which follows the law, "Noise and Vibration Control Act" can actually serve good condition to carry much more economical and effective blasting. The instruments used for this study are the SV-1 model, as first instrument in korea which can measure vibration velocity and vibration level at the same time.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.11 no.1
• /
• pp.68-79
• /
• 2008

Because local cities are different from large cities, they need to reflect their own characteristics of housing market. Thus in order to obtain useful implications for the establishing sound housing market in Jinju City, this paper investigated the characteristics of spatial distribution and determinant factors that affect apartment price in Jinju City. GIS representation of the apartments showed that most of old and small apartments were built in 'land readjustment project' areas executed in 1970s. On the contrary, new and large scale apartment complexes were built quite recently and distributed in the western and southern parts of the city. Next, in order to examine the factors which affect apartment price, this paper subtracted firstly several variables from the related studies. However in order to avoid multi-colinearity, variables were summarized by means of factor analysis. Then, setting apartment price as a dependant variable, 12 hedonic price models were established with 33 independent variables. As results, building age, floor area, accessibility to university and hospital, accessibility to arterial road, and stair-type building were turned out to be significant. These results will be used in making the supply and allocation plan of urban facilities and housing. Finally as conclusions this paper emphasized the need of periodic analysis of local housing market and establishing detailed housing information systems.

• Korean Journal of Environmental Biology
• /
• v.33 no.4
• /
• pp.459-467
• /
• 2015

Understanding of a carbon storage in a regional scale ecosystem is a very important data for predicting change of global carbon cycle. Therefore, the real data collected in the various ecosystems are a very useful for enhancing accuracy of model prediction. We tried to estimate total accumulated ecosystem carbon in Deogyusan National Park (DNP) with naturally well preserved ecosystem. In DNP, vegetations were classified to four main communities with Quercus mongolica community (12,636.9 ha, 54.8%), Quercus variabilis community (2,987.0 ha, 13.0%), Pinus densiflora community (5,758.0 ha, 25.0%), and Quercus serrata community (402.9 ha,1.7%). Biomass and soil carbons were estimated by the biomass allometric equations based on the DBH and carbon contents of litter and soil (0~30 cm) layers collected in 3 plots ($30cm{\times}30cm$) in each community. The biomass and soil carbons were shown as high value as 1,759,000 tC and 7,776,000 tC, respectively, in Quercus mongolia community in DNP area. In Quercus mongolica, Quercus variabilis, Quercus serrata, Pinus densiflora communities, the accumulated ecosystem carbon were shown 9,536,000 tC, 1,405,000 tC, 147,000 tC, 346,000 tC, respectively. Also, the total ecosystem carbon was estimated with 11,434,000 tC in DNP.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.43 no.1
• /
• pp.93-108
• /
• 2016

One of the fields to which the 3D printing technology can be applied is the field of medicine. Recently, the application of 3D printing technology to the bio-medical field has been gradually increasing with the commercializing of the bio-compatible or bio-degradable materials. The technology is currently contributing to the biomedical field by reducing times required for operations or minimizing adverse effects through preoperative identification of post-surgical consequences or model surgery with artificial bones and organs. This technology also enables the production of customized biomedical auxiliary products like hearing aids or artificial legs etc. For the field of dentistry, the 3D printing technology is also expected to elevate the level of dental treatment by making the customized orthodontic models, crown, bridge, inlay, and surgical guides for implant and surgery. However, issues remaining unidentified or incomplete in printing materials, modeling technology, software technology associated with CAD, verification of bio-stability and bio-effectiveness of materials or in compatibility and standardization of the technology are yet to be solved or be clarified for the full-scale application of the 3D printing technology, thus, it seems such issues should be resolved through further studies.

• Journal of Korea Water Resources Association
• /
• v.49 no.6
• /
• pp.519-528
• /
• 2016

Frequently torrential rain is occurred by climate change and urbanization. Urban is formed with road, residential and underground area. Without detailed topographic flooded analysis consideration can take a result which are wrong flooded depth and flooded area. Especially, flood analysis error of population and assets in dense downtown is causing a big problem for establishments and disaster response of flood measures. It can lead to casualties and property damage. Urban flood analysis is divided into sewer flow analysis and surface inundation analysis. Accuracy is very important point of these analysis. In this study, to confirm the effects of the elevation data precision in the process of flooded analysis were studied using 10m DEM, LiDAR data and 1:1,000 digital map. Study area is Dorim-stream basin in the Darim drainage basin, Sinrim 3 drainage basin, Sinrim 4 drainage basin. Flooding simulation through 2010's heavy rain by using XP-SWMM. Result, from 10m DEM, shows wrong flood depth which is more than 1m. In particular, some of the overflow manhole is not seen occurrence. Accordingly, detailed surface data is very important factor and it should be very careful when using the 10m DEM.

• Korean Journal of Veterinary Research
• /
• v.28 no.1
• /
• pp.125-135
• /
• 1988

Attempts of these studies were made to investigate the nonspecific congenital focal accumulation of ectodermal glial cells in the brain of normal piglets. The brain samples were taken from 1-,10-,20-,35-,45- and 70-day-old piglets from a SPF-pig farm and three model pig farms. Occurrences of neuroglial cell foci (NCF) on the brain were observed with light microscope. Appearance degrees of the congenital NCF on 10 to 16 cross section slides per a piglets brain were tentatively designed on a scale from degree+ to ⧻by NCF number: +, less than 20 of NCF number; ⧺, 21-40 of NCF number: ⧻, more than 41 of NCF number. The results obtained were as follows: 1. NCF in the brain were observed mainly on the cerebrum. Regions of higher frequencies on the cerebrum were ordered as subependymal layers of the lateral ventricles, peripheral regions of lateral ventricles in the white matter and some neuron layers under the molecular layer of the gray matter. But NCF were not observed in the cerebellum, pons, medulla oblongata and spinal cords. 2. On the subependymal layers of the lateral ventricles, NCF were observed in 100% of 27 piglets, and appearance degree of ⧻ was observed in 10 piglets(37.0%), ⧺ in 10 piglets(37.0%) and + in 7 Piglets(26.0%) of 27 piglets, respectively. 3. On the white matter of the cerebrum, NCF were observed in 25 piglets(92.6%) of 27 piglets, and appearance degree of ⧻ was observed in 3 piglets(11.1%), ⧺ in 13 piglets(48.2%), + in 9 piglets(33.3%) and - in 2 piglets(7.4%) of 27 piglets, respectively. 4. On the gray matter of the cerebrum, NCF were observed in 21 piglets(77.8%) of 27 piglets, and appearance degree of ⧻ was not observed, appearance degree of ⧺ was observed in 6 piglets(22.2%), + in 15 Piglets(55.6%) and - in 6 piglets(22.2%) of 27 Piglets, respectively. 5. NCF tended to be converged appearance on some regions and tended to be decreased markedly from 35th day after birth, and the shapes of NCF were: global or oval forms crowded by analogous shaped and stained cells in the empty spaces of the brain substrate or on one side of the blood vessels.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.1
• /
• pp.1-8
• /
• 2015

Wind power systems have gained much attention due to the relatively high reliability, good infrastructures and cost competitiveness to the fossil fuels. Advances have been made to increase the power efficiency of wind turbines while less attention has been focused on structural integrity assessment of structural sub-systems such as towers and foundations. Among many parameters for integrity assessment, the most perceptive parameter may be the induced horizontal displacement at the hub height although it is very difficult to measure particularly in large-scale and high-rise wind turbine structures. This study proposes an indirect displacement estimation scheme based on the combined use of inclinometers and accelerometers for more convenient and cost-effective measurements. To this end, (1) the formulation for data fusion of inclination and acceleration responses was presented and (2) the proposed method was numerically validated on an NREL 5 MW wind turbine model. The numerical analysis was carried out to investigate the performance of the propose method according to the number of sensors, the resolution and the available sampling rate of the inclinometers to be used.