• 항공우주시스템공학회지
• /
• 제14권6호
• /
• pp.74-78
• /
• 2020

The cooler driver electronics (CDE) for maintaining a low temperature of a satellite payload IR sensor has a compressor with a pulsation current load when in operation. This pulsation current creates a large voltage fluctuation and may negatively affect both the load and regulated bus stability. Thus, a CDE power conditioning system has a battery for use as a buffer that is connected in front of the CDE load line. In this system, a battery charger limiter circuit is required to protect from an over-charge of the battery and power to the load. In this study, an optimal design and parameter selection were developed and simulated.

• 한국산업정보학회논문지
• /
• 제19권1호
• /
• pp.31-41
• /
• 2014

정지궤도위성은 다수의 탑재체를 하나의 위성체 플랫폼에 탑재하고 2010년 6월 26일에 발사되었다. 전력계는 태양 및 식 기간 상태에서 완전 조절 $50V_{DC}$ 전력 버스를 제공한다. 위성에서 요구되는 전력은 태양전지 배열기 윙에서 생성되며, 에너지는 192.5Ah 용량의 리튬-이온 배터리에 저장된다. 본 논문은 전력계의 성능 평가를 향후 정지궤도위성 설계에 활용하기 위해 전력계의 중요 설계 변수들을 선정하고, 지상에서 시험 결과와 궤도상에서 운영 결과를 비교 분석하였다. 설계로부터 궤도상에서 운영 결과까지의 성능 평가를 통해 전력계는 중요한 성능감소 없이 정상적으로 동작되고 있음을 입증하였다.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2006년도 Proceedings of ISRS 2006 PORSEC Volume I
• /
• pp.271-273
• /
• 2006

In this paper, we describe the MI2U ORB function which is a part of the flight software executed on SCU and controls MI2U/MI which is one of three payloads on COMS. The MI2U ORB function manages MI2U/MI redundancy and reconfiguration, monitors MI2U/MI equipment, performs FDIR, and provides the routing service of commands from Ground/IP (Interpreted Program) through the current used 1553 channel. The MI2U hardware achieves the interface between the SCU and the MI. The MI2U is connected to SCU through MIL-STD-1553B system bus. The MI2U has the internal redundancy but is used in cold redundancy. The MI2U ORB function considers that they are not expected to be simultaneously switched on. The connection combination between MI2U and MI is electrically cross-strapped. However the MI2U ORB function considers only two combinations (MI2U A + MI 1, MI2U B + MI 2). Other combinations can be manually achieved by ground in case of the emergency case.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2005년도 Proceedings of ISRS 2005
• /
• pp.593-596
• /
• 2005

The MSC is a remote sensing instrument with very high performance that is to be installed on KOMPSAT2 satellite. The MSC consists of EOS (Electro-Optic Subsystem), PMU (Payload Management Unit) and PDTS (Payload Data Transmission Subsystem). PMU controls and monitors all the other payload units by sending commands and collecting telemetry. PMU is in charge of interfacing between payload system and satellite bus system. PMU gets commands from ground-station via OBC (On-Board Computer) that is a main controller of the satellite bus system and sends telemetry to the ground-station via OBC. There is a processor module, called SBC (Single Board Computer) in the PMU. The SBC is a main controller of the MSC system. The main roles of the SBC are payload mission management, command validation and execution, telemetry collection and monitoring, ancillary data handling, event reporting, power control of payload sub-units and communication with these units. Intel's 80486DX2 processor has been used for the SBC. Due to the fact that the SBC plays important roles for imaging mission execution and handles a lot of control data that is required for payload operation, it is required to make analysis of the CPU load when it is in maximum operation mode. In this paper, the analysis and measurement results of the SBC throughput in the maximum operation mode.

• 한국항공우주학회지
• /
• 제41권8호
• /
• pp.605-612
• /
• 2013

중형 또는 대형 인공위성은 발사를 앞두고 발사체 회사와 함께 연성하중해석을 실시하여 위성설계를 최종 검증한다. 연성하중해석을 통해 얻어진 최대가속도, 최소간극, 최대하중은 인공위성의 설계하중과 비교하여 인공위성의 설계를 최종적으로 검증하게 된다. 이러한 연성하중해석의 신뢰도를 높이기 위해서는 인공위성 유한요소모델은 충분히 검증되어야 하는데, 발사 직전에 수행하는 정현파 진동시험결과에 맞춰 보정한다. 본 논문에서는 연성하중해석을 위한 유한요소모델의 보정 및 검증결과에 대해 기술한다.

• International Journal of Aeronautical and Space Sciences
• /
• 제8권2호
• /
• pp.89-97
• /
• 2007

COMS(Communication, Oceanography, and Meteorology Satellite) is the first Korean multi-purpose satellite which is planned to be deployed at the altitude of geosynchronous orbit above the Korean peninsular. Noting that COMS is composed of the main BUS structure, two deployable solar panels, one yoke, five reactions wheels, COMS is treated as a collection of 9 bodies and its nonlinear equations of motion are obtained using the multi-body dynamics approach. Also, a computer program is developed to analyze the COMS motion during the various mission phase. Quite often, the equations of motion have to be derived repeatedly to reflect the fact that the spacecraft dynamics change as its configuration, and therefore its degree of freedom varies. However, the equations of motion and simulation software presented in this paper are general enough to represent the COMS dynamics of various configurations with a minimum change in input files. There is no need to derive the equations of motion repeatedly. To show the capability of the simulation program, the spacecraft motion during the solar array partial and full deployment has been simulated and the results are summarized in this paper.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2006년도 한국우주과학회보 제15권1호
• /
• pp.133-136
• /
• 2006

대형위성과 달리 나노위성이나 마이크로위성과 같은 소형위성의 경우, 전장품을 장착하기 위한 위성 내부 공간은 극히 제한되어 있다. 이러한 문제를 완화하기 위해 나노위성 HAUSAT-2는 대부분의 서브시스템과 탑재체의 전장모듈들을 통합한 일체형 위성 버스전장박스(BEU)를 개발하였다. 본 논문에서는 개발된 버스전장박스의 설계, 환경시험 결과 및 성능 분석에 대해 기술하였다.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2006년도 Proceedings of ISRS 2006 PORSEC Volume I
• /
• pp.220-223
• /
• 2006

The COMS(Communication, Ocean and Meteorological Satellite) EPS(Electrical Power Subsystem) is derived from an enhanced Eurostar 3000 EPS which is fully autonomous operation in normal conditions or in the event of a failure and provides a high level of reconfiguration capability and flexibility. This paper introduces the COMS EPS preliminary design result. The COMS EPS consists of a battery, a solar array wing, a PSR(Power Supply Regulator), a PRU(Pyrotechnic Unit), a SADM(Solar Array Drive Mechanism) and relay and fuse brackets. This can offer a bus power capability of 3 kW. The solar array is made of a deployable wing with two panels. One type of solar cells is selected as GaAs/Ge triple junction cells. Li-ion battery is base lined with ten series cell module of five cells in parallel. PSR associated with battery and solar array generates a power bus fully regulated 50 V. Power bus is centralised protection and distribution by relay and fuse brackets. PRU provides power for firing actuators devices. The solar array wing is routed by the SADM under control of the AOCS(Attitude Orbit Control Subsystem). The control and monitoring of the EPS especially of the battery, is performed by the PSR in combination with on-board software.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2006년도 Proceedings of ISRS 2006 PORSEC Volume I
• /
• pp.67-70
• /
• 2006

KARI is developing Image Data Acquisition and Control System (IDACS) for pre-processing meteorological and ocean data acquired on geostationary orbit. This paper describes the functions and architecture of IDACS and gives its operation policy including backup operation to overcome limitation of single-configured antenna system. The COMS IDACS provides the capability to receive the raw sensor data and disseminate processed MI data to users via a satellite. From the processed image data, users can produce a set of meteorological and ocean products for a wide range of applications. Most of IDACS subsystems are being developed by Korean technologies and experience acquired from previous projects. In case of COMS geometric correction software module, as it is closely dependent on the characteristics of imagers and spacecraft bus system, it is being co-developed with overseas prime contractor who develops spacecraft bus system.

• Journal of Electrical Engineering and information Science
• /
• 제3권1호
• /
• pp.14-20
• /
• 1998

The resistive shunting for the fine control of a Direct Energy Transfer(DET) systems is fully developed, but the non-resistive shunting using variable size solar array segments is in progress. This paper presents the spacecraft power control through switching of solar array segments, which uses a fully regulated DET power regulation. This method eliminates a dissipative element and removes the associated design limitations which arise from the dissipative elements for radiating cooling in deep space. The switching shunt regulator comprises the switched Solar Array Shunt(SAS) modules that regulate the solar array power. These SAS modules connect/disconnect the solar array segments to/from the bus according to the loading in the main bus without significant variations in the dissipation level. In this paper, twelve segments are used in the shunting. In order to verify the basis of analysis, the computational result of an analytic loop gain is performed.