• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.243-243
• /
• 2010

Low-temperature grown (LTG) InGaAs epilayers were grown by MBE technique for studying a correlation between terahertz (THz) emission and the intrinsic defects. The 1.2-um-thick Be-compensated LTG-InGaAs epilayers were prepared on SI-InP:Fe substrate at $200-250^{\circ}C$, and subsequently in-situ annealed under As environment at $550^{\circ}C$ for 5-30 minutes. The carrier concentration/mobility and the crystalline structure were analyzed by the Hall effect and the x-ray diffraction (XRD), respectively, and the carrier lifetime were determined by the fs time-resolved pump-probe spectroscopy. THz generation from LTG-InGaAs was carried out by a Ti-sapphire laser (800 nm) of a pulse width of 190 fs at a repetition of 76 MHz. Figure shows the spectral amplitude of generated waves in the THz region. As the growth temperature of epilayer increases, the amplitude is enhanced. However, two samples grown at $200^{\circ}C$, as-grown and annealed, show almost no difference in the spectral amplitude. This suggests that the growth temperature is critical in the formation of defect states involved in THz emission. We are now investigating the correlations between the XRD band attributed to defects, the Hall parameter, and the spectral amplitude of generated THz wave.

• 한국레이저가공학회지
• /
• 제15권3호
• /
• pp.16-19
• /
• 2012

We have successfully formed brown colored patterns inside of a transparent borosilicate glass generally known as BK7, laying the focus of near infrared Ti: sapphire femtosecond laser beam in the bulk BK7 glass. It is important to keep the laser power well below the damage threshold of BK7 in forming the color center. According to the low laser power, there was no laser induced mechanical damage such as cracks or threads in the color formed area. From the absorbance spectrum and its gaussian fitting, we found the band gap of BK7, 4.21eV, and three absorption edges.

• 한국재료학회지
• /
• 제23권12호
• /
• pp.732-736
• /
• 2013

AlN epilayers were grown on a c-plane sapphire substrate using hydride vapor phase epitaxy (HVPE). A series of AlN epilayers were grown at $1120^{\circ}C$ with V/III ratios 1.5, 2.5 and 3.5, and the influence of V/III ratio on their properties was investigated. As the V/III ratio was increased, the surface roughness (RMS roughness), Raman shift of $E_2$ high peaks and full-width at half-maximum (FWHM) of symmetrical (002) & asymmetrical (102) of the AlN epilayers increased. However, the intensities of the Raman $E_2$ high peaks were reduced. This indicates that the crystal quality of the grown AlN epilayers was degraded by activation of the parasitic reaction as the V/III ratio was increased. Smooth surface, stress free and high crystal quality AlN epilayers were obtained at the V/III ratio of 1.5. The crystal quality of AlNepilayers is worsened by the promotion of three-dimensional (3D) growth mode when the flow of $NH_3$ is high.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.31-31
• /
• 2000

Al2O3는 높은 화학적, 열적 안정성으로 인하여 미세전자 산업에서 절연막이나 광전자소자의 재료로써 널리 이용되고 있다. 특히, 사파이어는 고위도의 LED, 청색 LD의 재료인 GaN 계열의 III-Nitride 물질을 성장시킬 때 필요한 기판으로 보편적으로 사용되고 있다. 이러한 GaN계열의 광소자 제조에서 사파이어 기판을 적용시 지적되는 문제점들 중의 하나는 소자제조 후 사파이어의 결정 구조 및 높은 경도에 의해 나타나는 cutting 및 backside의 기계적 연마가 어렵다는 것이다. 최근에는 이온빔 식각이나 이온 주입 후 화학적 습식 시각, reactive ion etching을 통한 사파이어의 건식 식각이 소자 분리 및 backside 공정을 우해 연구되고 있다. 그러나 이러한 방법을 이용한 사파이어의 식각속도는 일반적으로 15nm/min 보다 작다. 높은 식각율과 식각후 표면의 작은 거칠기를 수반한 사파이어의 플라즈마 식각은 소자 제조 공정시 소자의 isolation 및 lapping 후 연마 공정에 이용할 수 있다. 본 연구에서는 평판 유도결합형 플라즈마를 이용하여 Cl2/BCL3/Ar 의 가스조합, inductive power, bias voltage, 압력, 기판온도의 다양한 공정 변수를 통하여 (0001) 사파이어의 식각특성을 연구하였다. 사파이어의 식각속도는 inductive power, bias voltage, 그리고 기판 온도가 증가할수록 증가하였으며 Cl2에 BCl3를 50%이하로 첨가할 때 BCl3 첨가량이 증가할수록 식각속도 및 식각마스크(photoresist)와의 식각선택비가 증가하는 것을 관찰하였다. 또한, Cl3:BCl3=1:1의 조건에 따라 Ar 첨가에 따른 식각속도 및 표면 거칠기를 관찰하였다. 본 연구의 최적 식각조건인 40%Cl2/40%BCl3/20%Ar, 600W의 inductive power, -300V의 bias voltage, 30mTorr의 압력, 기판온도 7$0^{\circ}C$에서 270nm/min의 사파이어 식각속도를 얻을수 있었다. 그리고 이러한 식각조건에서 표면의 거치기를 줄일수 있었다. 사파이어 식각은 보편적인 사파이어 lapping 공정시 수반되어 형성된 표면의 거치기를 줄이기 위한 마지막 공정에 응용될수 있다. 사파이어의 식각시 나타나는 식각 부산물은 플라즈마 진단방비인 optical emission spectroscopy (OES)를 통하여 관찰하였고, 식각시 사파이어의 표면성분비 변화 및 표면의 화학적 결합은 X-ray photoelectron spectroscopy(XPS)를 사용하여 측정하였다. 시각 전, 후의 표면의 거칠기를 scanning electron microscopy(SEM)을 통하여 관찰하였다.

• 한국진공학회지
• /
• 제18권5호
• /
• pp.377-383
• /
• 2009

라디오파 마그네트론 스퍼터링 방법을 사용하여 사파이어 기판 위에 Al 도핑된 ZnO (AZO) 박막을 성장시킨 후에 온도 범위 $600-900^{\circ}C$에서 급속 열처리를 수행하였다. 박막의 결정 구조와 표면 형상은 각각 X-선 회절법과 주사전자현미경으로 조사하였다. 급속 열처리 온도가 증가함에 따라 박막의 결정성은 향상되었고, 평균 50 nm의 크기를 갖는 육각형 형태의 결정 입자가 관측되었다. 증착된 모든 박막은 파장 영역 400-1100 nm에서 92%의 평균 투과율을 나타내었다. 열처리 온도가 증가함에 따라 박막의 밴드갭 에너지는 감소하였고, 광여기 발광 신호의 경우에 자외선 발광 신호의 세기가 감소하면서 400 nm에 중심을 둔 보라색 발광 신호가 주된 피크를 형성하였다. 박막의 전기적 특성은 열처리 온도에 현저한 의존성을 보였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.146-146
• /
• 2011

The blue light emitting diode (LED) structure based on non-polar a-plane (11-20) GaN which was coated TiO2 nanoparticles using spin coating method was grown on r-plane (1-102) sapphire substrates to improve light extraction efficiency. We report on the emission and structural properties with temperature dependence of photoluminescence (PL) and x-ray rocking curves (XRC). From PL results at 13 K of undoped GaN samples, basal plane stacking fault (BSF) and near band edge (NBE) emission peak were observed at 3.434 eV and 3.484 eV, respectively. We also found the temperature-induced band-gap shrinkage, which was fitted well with empirical Varshini's equation. The PL intensity of TiO2 nanoparticles ?coated multiple quantum well (MQW) sample is decayed slower than that of no coating sample with increasing temperature. The anisotrophic strain and azimuth angle dependence in the films were shown from XRC results. The full width at half maximum (FWHM) along the GaN [11-20] and [1-100] directions were 564.9 arcsec and 490.8 arcsec, respectively. A small deviation of FWHM values at in-plane direction is attributed to uniform in-plane strain.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.148-149
• /
• 2012

This paper reports doping of carbon atoms in GaN layer, which based on dimethylhydrazine (DMHy) and growth temperature. It is well known that dislocations can act as non-radiative recombination center in light emitting diode (LED). Recently, many researchers have tried to reduce the dislocation density by using various techniques such as lateral epitaxial overgrowth (LEO) [1] and patterned sapphire substrate (PSS) [2], and etc. However, LEO and PSS techniques require additional complicated steps to make masks or patterns on the substrate. Some reports also showed insertion of carbon doped layer may have good effect on crystal quality of GaN layer [3]. Here we report the growth of GaN epitaxial layer by inserting carbon doped GaN layer into GaN epitaxial layer. GaN:C layer growth was performed in metal-organic chemical vapor deposition (MOCVD) reactor, and DMHy was used as a carbon doping source. We elucidated the role of DMHy in various GaN:C growth temperature. When growth temperature of GaN decreases, the concentration of carbon increases. Hence, we also checked the carbon concentration with DMHy depending on growth temperature. Carbon concentration of conventional GaN is $1.15{\times}1016$. Carbon concentration can be achieved up to $4.68{\times}1,018$. GaN epilayer quality measured by XRD rocking curve get better with GaN:C layer insertion. FWHM of (002) was decreased from 245 arcsec to 234 arcsec and FWHM of (102) decreased from 338 arcsec to 302 arcsec. By comparing the quality of GaN:C layer inserted GaN with conventional GaN, we confirmed that GaN:C interlayer can block dislocations.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.111-114
• /
• 2003

Effects of substrate materials on the microstructure and the sensitivity of $SnO_2$thin film gas sensors have been studied. Various substrates were studied, such as oxidized silicon, sapphire, polished alumina, and unpolished alumina. It was observed that strong correlation exists between the electrical resistance and the CO gas sensitivity of the manufactured sensors and the surface roughness of $SnO_2$thin films, which in turn was related to the surface roughness of the original substrates. X$SnO_2$thin film gas sensor on unpolished alumina with the highest surface roughness showed the highest initial resistance and CO gas sensitivity. The transmission electron microscopy observation indicated that shape and size of the columnar microstructure of the thin films were not critically affected by the type of substrates.

• 한국재료학회지
• /
• 제9권9호
• /
• pp.878-882
• /
• 1999

분자선증착법으로 (0001) 사파이어 기판 위에 $Al_xGa_1-_xN$ 에피층을 AlN 몰비를 변화시키면서 성장시켰다. AlN 몰비는 0.16에서 0.76까지 변화시켰으며 X선의 회절 실험과 Rutherford backscattering spectroscopy 방법을 이용하여 AlN 몰비를 결정하였다. $Al_xGa_1-_xN$ 에피층의 깊이 방향의 조성 변화를 관찰하였으며 스퍼터 시간에 대해 각 원소가 일정한 원자 농도를 가짐을 알 수 있었다. AlN 몰비의 증가에 따른 표면 특성의 변화를 관찰하기 위하여 atomic force microscopy 측정을 수행하였다. 표면에서의 입자 모양이 AlN 몰비가 변화함에 따라 원형에서 침상형태로 변화함을 알 수 있었다. 표면 입자에 대한 root mean square 값과 average roughness 값을 구하였으며 AlN 몰비를 바꿈에 따라 나타나는 변화를 관찰하였다.

• 한국표면공학회지
• /
• 제42권2호
• /
• pp.68-72
• /
• 2009

We report on the growth of $CuCrO_2$ films using pulsed laser deposition and their structural and electrical transport properties. $CuCrO_2$ thin films were doped with 5 at% Mg for p-type properties. Epitaxial films of $CuCr_{0.95}Mg_{0.05}O_2$ were grown on c-plane sapphire substrates. The effects of growth temperature and oxygen pressure on film properties were investigated. The main phase of delafossite $CuCr_{0.95}Mg_{0.05}O_2$ was appeared above the growth temperature of $600^{\circ}C$. The thin film grown at $500^{\circ}C$ showed the highest conductivity, reaching 19.6 S/cm while higher growth temperatures over $500^{\circ}C$ led to lower conductivity; the thin film grown at $700^{\circ}C$ showed 0.02 S/cm.