• Magazine of the Korean Society of Agricultural Engineers
• /
• v.27 no.4
• /
• pp.53-60
• /
• 1985

The plaster mixed to loam and sandy soil from 4 to 12 percent by dry soil weight, and the compaction, permeability, CBR, unconfined compressive strength and freezingthawing test were performed The results obtained are summarized as follows; 1.The coefficient of permeability reduced sharply at the plaster content of 4 percent, and in the CBR test, the swelling ratio reduced by the increment of plaster content. 2.The addition of plaster increased the unconfined compressive strength by the cementing effect, and it was found that the optimum plaster content, existed with the soil type, which showed the maximum strength 3.It was possible to enhance the unconfined compressive strength of the gypsum-lime-soil mixtures when the optimum content of plaster was mixed to the hydrated lime. 4.In case of sandy soil, the relative frost heave decreased with the mixture of plaster, however in loam soil, the relative frost heave began to increase at the plaster content of 12 percent than non-treated soil. Therefore the optimum plaster content existed for protecting frost heave by the different soil type. 5.The above summarized results make it possible to expect the effects such as improvement of soil properties, decrement of permeability, increment of unconfined compressive strength, and protection of frost heave, etc, therefore, it is considered that it is possible to it is plaster as sub-base materials of road.

• Journal of Environmental Science International
• /
• v.25 no.3
• /
• pp.337-343
• /
• 2016

The present study aimed to determine the influence of various root restriction media on seedling quality and early growth of strawberry after transplanting. The root activity of the seedlings, measured 20 days after fixation, was considerably higher (0.096, 0.090, and $0.063mg{\cdot}g^{-1}{\cdot}h^{-1}$ at 420, 450, and 480 nm, respectively) in expanded rice hull (ERH) treatment than in the sandy loam and loamy sand treatments. The volumetric water content (VWC) of the root media tested across 3 irrigation regimes (15 d, 30 d, 45 d) in the nursery field was highest in sandy loam (65.0-66.8%), followed by 59.4-61.3% in loamy sand and 38.6-45.3% in ERH. When growth parameters of runner plantlets were compared, ERH treatment was found to result in the highest crown thickness and fresh weights of root and above-ground parts. This had a favorable influence on above-ground tissue growth after transplanting to plastic house soil. As mentioned above, ERH treatment resulted in the highest seedling quality and early growth after transplanting. The results of this study would serve as useful on-site data for the production of high-quality strawberry seedlings.

• Journal of Plant Biology
• /
• v.14 no.3
• /
• pp.21-28
• /
• 1971

Dry matter production, leaf area growth and total nitrogen changes were studied in Glycine max. soybean communities, which were grown in sandy loam soils controlled to provide various moisture levels, i.e., 5-7%(level 1), 8-10%(level 2), 11-13%(level 3), 14-15%(lev디 4), 17-20%(level 5) and 22-24%(level 6). A summary of the results is shown. The maximum dry matter production of leaves, stems and nodules and the maximum leaf area per unit area were at level 5, but the maximum of root dry matter production was at level 4. Total nitrogen content of the soybean plant decreased with growth, but each level of soil moisture content also showed a little difference. Water content of the plant decreased with plant age and soil water deficiency, especially in roots and nodules. Nodule formation increased in proportion to soil moisture content. total nitrogen content of the soil on which the soybeans grew, increased from 0.23% before sowing to 0.30% at 100 days after sowing. It seems that soil water content acts as a linear factor in the elongation or dry weight increase of shoots and roots until increasing to level 5. Considering the pattern of plant growth through analysis of the shoot and root dry weight ratio, or the photosynthetic organ and non-photosynthetic organ dry weight ratio, the asymptote of plant growth at a high soil water content exceeded that at a low soil water content.

• Journal of Forest and Environmental Science
• /
• v.36 no.4
• /
• pp.259-266
• /
• 2020

Poplar trees from the Salicaceae family over the years have been utilized for various reasons which include prevention of deforestation as well as phytoremediation. This study aims to determine the optimal pre-treatment and soil conditions required for propagation of poplar cuttings for increased initial adaptability and survival rate. Five poplar clones (Hanan, 110, 107, DN-34, 52-225) were selected for IBA, soil composition treatments on propagation. IBA pre-treatment of cuttings were utilized 0, 10, and 100 mg l-1 concentrations. Soil compositions were amended with TKS-2+perlite 2:1 (v:v) and sandy clay loam mixed with artificial soil. According to the greenhouse results 10 mg l-1 of IBA showed a significant increase in plant height whereas 100 mg l-1 inhibited plant growth except in clone 110. Soil composition severely affected root growth and hence overall growth of the clones. Sandy clay loam soil had poor to stunted growth compared to TKS-2+perlite.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.10
• /
• pp.199-206
• /
• 2019

This study aims to recycle redmud which is a byproduct in the alumina industry. Redmud ceramics were prepared according to the type of raw materials by blending redmud with the raw materials used in the conventional clay bricks. In this paper, the compressive strength, water absorption ratio, and shrinkage of redmud ceramics prepared by mixing clay bricks were evaluated. Compressive strength and absorption ratio of redmud ceramics were compared with the clay brick criteria of KS L 4201. At the firing temperature of $1200^{\circ}C$, the specimens containing redmud only and the redmud with sandy loam and black clay were found to satisfy the 1st class of clay brick. The quality standard of compressive strength and absorption ratio was obtained by firing redmud with black clay and sandy loam at $1200^{\circ}C$. Also, when the redmud was mixed with black clay and feldspar, the 2nd class was satisfied when the sample was fired at $1100^{\circ}C$.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.6
• /
• pp.577-584
• /
• 1994

A field trial was carried out to select suitable crops for diverted upland from paddy field and to investigate response of several forage crops to soil properties and ground water levels of the diverted upland at Suwon area of Korea in 1992 and 1993. Experiments were conducted in sandy loam plot and comparatively clay loam plot having higher ground water level. Rye (Paldang), triticale (Shinki), italian ryegrass (Tetraflorum) were used as wintering forage crops and maize(Suwon 19), sorghum-sudangrass hybrid(Pioneer855F), pearl millet(Suwon 6), japanese millet (King) were used as summer forage crops. Growth and yield of forage crops were better and higher in sandy loam soil having low ground water level. Among wintering forage crops, triticale recorded the highest forage yield. Rye showed high forage yield in sandy loam soil and italian ryegrass hardly survived in diverted upland of Suwon area during winter. Among summer forage crops, forage yield of sorghum-sudangrass hybrid was highest. Yield of japanese millet was not affected by soil conditions in both plots. Yields of pearl millet and maize remained relatively low in both plots.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.3
• /
• pp.260-267
• /
• 2010

As sloped farmland is subject to runoff and soil erosion and consequently require appropriate vegetative coverage to conserve soil and water, a field study was carried out to evaluate the impact of crop canopy coverage on soil loss and runoff from the experimental plot with three different textural types (clay loam, loam, and sandy loam). The runoff and soil loss were examined at lysimeters with 15% slope, 5 m in length, and 2 m in width for five months from May to September 2009 in Suwon ($37^{\circ}$ 16' 42.67" N, $126^{\circ}$ 59' 0.11" E). Red pepper (Capsicum annum L. cv. Daechon) seedlings were transplanted on three different dates, May 4 (RP1), 15 (RP2), and 25 (RP3) to check vegetation coverage. During the experimental period, the vegetation coverage and plant height were measured at 7 day-intervals and then the 'canopy cover subfactor' (an inverse of vegetation cover) was subsequently calculated. After each rainfall ceased, the amounts of soil loss and runoff were measured from each plot. Under rainfall events >100 mm, both soil loss and runoff ratio increased with increasing canopy cover subfactor ($R^2$=0.35, p<0.01, $R^2$=0.09, p<0.1), indicating that as vegetation cover increases, the amount of soil loss and runoff reduces. However, the soil loss and runoff were depending on the soil texture and rainfall intensity (i. e., $EI_{30}$). The red pepper canopy cover subfactor was more highly correlated with soil loss in clay loam ($R^2$=0.83, p<0.001) than in sandy loam ($R^2$=0.48, p<0.05) and loam ($R^2$=0.43, p<0.1) plots. However, the runoff ratio was effectively mitigated by the canopy coverage under the rainfall only with $EI_{30}$<1000 MJ mm $ha^{-1}hr^{-1}$ ($R^2$=0.34, p<0.05). Therefore, this result suggested that soil loss from the red pepper field could be reduced by adjusting seedling transplanting dates, but it was also affected by the various soil textures and $EI_{30}$.

• Economic and Environmental Geology
• /
• v.34 no.3
• /
• pp.301-306
• /
• 2001

Column tests were conducted to investigate the optimal condition of surfactant solution pH that can affect the removal efficiency in surfactant-assisted remediation. Toluene and 1,2,4-trichlorobenzene were chosen as the model hydrophobic substances. Two Iowa soils, Fruitfield sand and Webster clay loam, were leached with solutions of 4%(v/v) sodium diphenyl oxide disulfonate (DOSL, trade name Dowfax 8390), or 4%(v/v) trideceth-19-carboxylic acid (TDCA, trade name Sandopan JA36), or 4% (v/v) octylphenoxypoly ethoxyethanol (OPEE, trade name Triton X100). The test results revealed that a maximum removal of toluene and 1,2,4-trichlorobenzene was obtained at pH 10 of surfactant solution, and maximum recoveries of added toluene (94%) or 1 ,2,4- trichlorobenzene (97 %) were obtained for DOSL surfactant solution in Fruitfield sandy soil column. Increased removal efficiency by pH control of both toluene and 1,2,4trichlorobenzene was 16% and 20% for DOSL with Fruitfild sandy soil, respectively. In addition, the maximum recoveries of added toluene or I ,2,4-trichlorobenzene were 89% and 93% for DOSL surfactant solution in Webster clay loam soil column. The maximum increase of toluene and 1,2,4-trichlorobenzene removal was 26% and 19% for DOSL with Webster clay loam soil, respectively. These experimental results indicate that maintaining a high pH surfactant solution in surfactant-assisted remediation is desirable for efficient removal of NAPLs from contminated soils.

• Korean Journal of Environmental Agriculture
• /
• v.5 no.2
• /
• pp.95-100
• /
• 1986

A pot experiment was conducted to find out As uptake and critical levels affecting yield loss of rice plant. The arsenic was added to two soils of sand loam and loam in the from of $Na_2HAsO_4,\;7H_2O$ at different As concenterations of 0, 10, 25, 50, 100, 150 ppm, respectively. Rice yields significantly decreased with increasing soil As levels and the critical As levels in soils were estimated to be 6.79 ppm for loam and 2.75 ppm for sandy loam. Yield components also decreased with higher soil As levels and the weight of 1000 grains showed the highest significant correlation with As level in soil. Most of arsenic was retained by the roots and a small amount of arsenic was translocated to the shoots. Arsenic content in plant organs was high in the order of root>stem>leaf blade>leaf sheath>brown rice. The number of sterillized grains also increased with higher As level in soil and it was much higher in sandy loam than in loam.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.20 no.1
• /
• pp.4575-4591
• /
• 1978

In order to investigate the effects of grain size distribution, cement content, and molding pressure on the strength and durability of soil-cement mixtures, a laboratory test of soil cement mixtures was performed at four levels of cement content, five levels of molding pressure, and four levels of normal curing periods. The results are summarized as follows: 1. Optimum moisture contents in loam soil and maximum dry density in sand soil increased with the increase of cement content, but in others, both optimum moisture contents and maximum dry density were changed ununiformly. 2. When the specimens were molded with molding pressure, 50kg/$\textrm{cm}^2$, strength of soil cement mixture with cement content, 2 and 4 per cent, was lower than the strength of soil cement mixture without cement content by more than 40 to 50 per cent. 3. The strength of soil-cement molded with molding pressure, 100kg/$\textrm{cm}^2$, was higher than the strength of soil-cement molded with M.D.D. obtained from standard compaction test more than 40 per cent in sand loam cement and 50 per cent in loamy cement. 4. There was highly significant positive correlation among molding pressure, cement content and unconfined compressive strentgh and so the following multiple regression equations were obtained. Loam: fc=1.9693C+0.197P-0.84 Sandy loam: fc=2.9065C+0.235P-0.77 5. When the specimens were molded with molding pressure, 20 to 100kg/$\textrm{cm}^2$, the regression equation between the 28-day and 7-day strenght was obtained as follows. Loam : q28=1.1050q7+7.59(r=0.9147) Sandy loam : q28=1.3905q7+3.17 (r=0.9801) 6. At the cement contents of above 50 per cent, the weight losses by freeeze-thaw test were negligible. At the cement content of below 8 per cent the weight losses were singnificantly high under low molding pressure and remarkably decreased with the increase of molding pressure up to 80kg/$\textrm{cm}^2$. 7. Resistance to damage from water and to absorption of water were not improved by molding pressure alone, but when the soil was mixtured with cement above 6 per cent, damage seldoms occurred and absorbed less than 5 per cent of water. 8. There was highly significant inverse-corelationship between the compressive strength of soil cement mixtures and their freeze-thaw loss as well as water absorption. By the regression equation methods, the relationships between them were expessed as followed fc=-7.3206Wa+115.6(r=0.9871) log fc=-0.0174L+1.59(r=0.7709) where fc=unconfined compressive stregth after 28-days curing. kg/$\textrm{cm}^2$ Wa=water absorption, % L : freeze-thaw loss rate, %