• Magazine of the Korean Society of Agricultural Engineers
• /
• v.33 no.3
• /
• pp.51-62
• /
• 1991

A comprehensive laboratory investigation of the liquefaction characteristics of Jumunjin standard sand. Seoul sand and Hongsung sand was peformed by the undrained cyclic triaxial compression test under different relative densities, confining pressures and cyclic deviator stresses. The results obtained are as follows ; 1. Liquefaction potential was dominated by the stress ratio at a given number of cycle. That is, the number of cycle required to cause initial liquefaction became samller as the stress ratio increased. 2. Liquefaction potential of a sand was infliuenced by initial relative density or void ratio. Under a given relative density. liquefaction potential of Jumunjin standard sand and Seoul sand was smaller than that of Hongsung sand. 3. The pore pressure ratio of Hongsung sand was the smallest three under a given relative density and stress ratio, and it showed higher value when the cyclic stress and the shear strain were high. 4. An excessive pore pressure ratio not found when initial shear was smaller than 0.01%, and the pore pressure ratio started to increase when initial shear became greater than 0.01%. 5. Soil texture is an important factor to cause liquefaction, and liquefaction potential decreased a the mean grain size decreased. however the sand having fine grain such as Hongsung sand showed somewhat higher liquefaction potential. 6. Based on the analysis of the specimens whose number of the cycles to cause liquefaction was 8~12, it was found that the relationship between density and stress ratio was linear. The curves for Hongsung sand was steeper than the other. 7. From the above results and the method suggested by Seed-Idriss, it may be considered that the damages by Hongsung earthquake was not directly caused by liquefaction.

• Geomechanics and Engineering
• /
• v.37 no.5
• /
• pp.431-441
• /
• 2024

A newly developed line-style sand pluviator has been calibrated to prepare repeatable sand specimens of specific statuses of compactness and homogeneity for laboratory tests. Sand is falling via a bottom slot of a fixed hopper, and by moving the sample container under the slot, the container is evenly filled with sand. The pluviator is designed with high flexibility: The falling height of sand, the hopper's opening width and the relative moving speed between the hopper and the sample box can be easily adjusted. By changing these control factors, sand specimens of a wide range of densities can be prepared. A series of specimen preparation was performed using the coarse Merwede River sand. Performance of the pluviator was systematically evaluated by exploring the alteration of achievable density, as well as checking the homogeneity and fabric of the prepared samples by CT scanning. It was found that the density of prepared coarse sand samples has monotonic correlations with none of the three control factors. Furthermore, CT scanning results suggested that the prepared samples exhibited excellent homogeneity in the horizontal direction but periodical alteration of density in the vertical direction. Based on these calibration test results, a preliminary hypothesis is proposed to describe the general working principles of this type of pluviators a priori, illustrating the mechanisms dominating the non-monotonic correlations between control factors and the relative density as well as the vertically prevalent heterogeneity of specimens. Accordingly, practical recommendations are made in a unified framework in order to lessen the load of similar calibration work.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1290-1295
• /
• 2008

The relative density of soil indicate loose and dense state of sand. Because sand is low compressibility, initial relative density of sand is important effect factor of compression and shear behavior. To measure exactly relative density, the exactly maximum and minimum void ratio was determinated by laboratory tests. Generally, vibrating table method is adapted for minimum void ratio(KS F 2345). However KS F 2345 is not consider the particle break during the vibrating table test. In this study, The minimum void ratio is compared with a method of Pluviation and Vibrating table test results using the K-7(crushed sand). It is concluded that the K-7 sand particles were crushed during the vibrating table test and vibrating table test is not a suitable test for a crushed sand $e_{min}$.

• Geomechanics and Engineering
• /
• v.34 no.2
• /
• pp.197-208
• /
• 2023

Rate-dependent mechanical response of sand, subjected to loading of medium to high strain rate range, is of interest for several civilian and military applications. Such rate-dependent response can vary significantly based on the initial density state of the sand, applied confining pressure, considered strain rate range, drainage condition and sand morphology. A numerical study has been carried out employing a recently proposed visco-plastic constitutive model to explore the rate-dependent mechanical behaviour of Toyoura sand under drained triaxial loading condition. The model parameters have been calibrated using the experimental data on Toyoura sand available in published literature. Under strain rates higher than a reference strain rate, the simulation results are found to be in good agreement with the experimentally observed characteristic shearing behaviour of sand, which includes increased shear strength, pronounced post-peak softening and suppressed compression. The rate-dependent response, subjected to intermediate strain rate range, has further been assessed in terms of enhancement of peak shear strength and peak friction angle over varying initial density and confining pressure. The simulation results indicate that the rate-induced strength increase is highest for the dense state and such strength enhancements remain nearly independent of the applied confinement level.

• Nuclear Engineering and Technology
• /
• v.34 no.1
• /
• pp.90-103
• /
• 2002

The thermal and mechanical properties of compacted bentonite and bentonite-sand mixture were collected from the literatures and compiled. The thermal conductivity of bentonite is found to increase almost linearly with increasing dry density and water content of the bentonite. The specific heat can also be expressed as a function of water ontent, and the coefficient of thermal expansion is almost independent on the dry density. The logarithm of unconfined compressive strength and Young’s modulus of elasticity increase linearly with increasing dry density, and in the case of constant dry density, it can be fitted to a second order polynomial of water content. Also the unconfined compressive strength and Young’s modulus of elasticity of the bentonite-sand mixture decreases with increasing sand content. The Poisson’s ratio remains constant at the dry density higher than 1.6 Mg/m$_3$, and the shear strength increases with increasing dry density.

• Geomechanics and Engineering
• /
• v.8 no.4
• /
• pp.595-613
• /
• 2015

An experimental investigation into the uplift capacity of horizontal square plate anchors in sand with and without geogrid reinforcement is reported. The parameters investigated are the effect of the depth of the single layer of geogrid, vertical spacing of geogrid layers, number of geogrid layers, length of geogrid layers, the effects of embedment depth, and relative density of sand. A series of three dimensional finite element analyses model was established and confirmed to be effective in capturing the behaviour of plate anchor-reinforced sand by comparing its predictions with experimental results. The results showed that the geogrid reinforcement had a considerable effect on the uplift capacity of horizontal square plate anchors in sand. The improvement in uplift capacity was found to be strongly dependent on the embedment depth and relative density of sand. A satisfactory agreement between the experimental and numerical results on general trend of behaviour and optimum geometry of reinforcement placement is observed. Based on the model test results and the finite element analyses, optimum values of the geogrid parameters for maximum reinforcing effect are discussed and suggested.

• Resources Recycling
• /
• v.26 no.2
• /
• pp.66-70
• /
• 2017

The purpose of this research was to estimate density changes of sea sand by washing. To examine water content test, field density test, particle density test and measuring of dump regarding extracted sea sand and selling one. Measured result of mean particle density of barge and dump were $2.666g/cm^3$, $2.651g/cm^3$, respectively. Also, measured result of field density for each sea sand was $1.716g/cm^3$, $1.331g/cm^3$ on average. Converted to the volume of 1ton of each sea sand, $0.583m^3$, $0.751m^3$, respectively. Occurring to volume change approximately 28.8% on average. The mean field densities of measuring of sea sand that dump and barge were $1.398g/cm^3$ and $1.716g/cm^3$ respectively. This values indicated $0.715m^3$ and $0.583m^3$ each, when converted to the volume of sea sand 1ton. It was found that the average of 22.6% volume change occurred between the amount of sea sand and the sales volume.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.7
• /
• pp.37-46
• /
• 2013

Various sizes of gravels are included in the most field soils that are utilized for civil constructions. Especially, the small amounts of gravel are often included in selected soils for backfill materials, earth dams, and subbase ground. In such cases, the small amounts of mixed gravel and its shape may influence the determination of dry density of soils, which results in an inaccurate degree of compaction for soils in the field. In this study, a dry density of sand with various gravel contents (0, 10, 17, 23, 29 and 33%) and three different sizes (2.0-2.36, 3.35-4.75, 5.6-10.0 mm) was experimentally investigated for compacted or loosely packed conditions. The loosely packed sand with gravels was simulated by pouring sand into compaction mould and its density was determined. When a 33% of gravel content was mixed with sand, its dry density increased up to 15-20% for compacted specimen and 20-23% for loosely packed specimen. When a gravel content and size were the same, a dry density of compacted specimen was $0.1-0.16g/cm^3$ higher than that of loosely packed specimen. Even though the same gravel content was used, a dry density of sand with big gravels was $0.04-0.08g/cm^3$ higher than that of sand with small gravels for compacted specimen and $0.03-0.05g/cm^3$ for loosely packed specimen.

• The Korean Journal of Mycology
• /
• v.21 no.3
• /
• pp.235-245
• /
• 1993

The symbiotic properties of arbuscular mycorrhizal fungi(AMF) such as the absence and/or presence of symbiosis, spore density, and six factors of phycochemical properties of soil were investigated in the rhizosphere of seven sand dune plants and three control plants around Kum river. The infection of AMF was confirmed in all plants. Three genera, nine species of the AMF spores were identified in the sand dune; Ac. scrobiculata, G. aggregatum, G. convolutum, G. diaphanum, G. dimophicum, G. geosporum, G. vesiculiferum, G. tortuosum, S. pachycaulis. All of them were also found in the control, but S. pachycaulis were only separated in the sand dune. In the control, three genera, four species were identified; G. flavisporum, Gi. margarita, Sc. gregaria. Sc. persica. The species specificity was not found between the sand dune plant and AMF. However, the AMF was thought to be correlated with the soil factors. The spore density was stimulated with increase of the organic matter and the nitrogen content, but inhibited with the water content and the phosphorus content. In respect of the seasonal factor, the spore density was increased in the late growth period of plants.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.265-272
• /
• 1994

The relative density seems to be important as a factor of controlling the physical properties in the case of cohesionless soil ground as sand. Therefore, the study is more important about the method for reappearing the same relative density when the specimen of shearing test is to be produced or the model test of ground is to be made. In this study, the apparatus making use of the multiple sieving pluviation method - one of the reappearance of relative density - could be made. Using this apparatus, tests were practiced varying the factors such as the size of sieve mesh and the number of sieve, the amount of falling discharge, the falling height etc. about the standard sand in Jumunjin and Hadong sand. When laboratory test is performed by the cohensionless soil , it presents the method for reappearing of the relative density in field.