• Advances in concrete construction
• /
• v.11 no.5
• /
• pp.409-417
• /
• 2021

The incorporation of non-biodegradable tyre waste in cement-based material has gained more interest towards sustainable construction these days. Crumb rubber (CR) from waste tyre is an alternative for sand replacement in low strength applications. Many researchers have studied CR cement-based materials produced by normal mixing (NM) method and reported a significant decrease in compressive strength due to CR. To compensate this strength loss, this research aims to study the innovative incorporation of CR in cement composite via the preplaced mixing (PM) method. In this investigation, cement composite was produced with NM and PM methods by replacing sand with 0%, 50%, and 100% CR by volume. The test results showed no significant difference in terms of densities of cement composite prepared with both mixing methods. However, cement composite prepared with PM method had lower strength reduction (about 10%) and lowered drying shrinkage (about 20%). In addition, the sound absorption coefficient and noise reduction coefficient of CR cement composite prepared by PM method were in similar range as those prepared with NM method. Overall, the results demonstrate that the PM method is promising, and the maximum replacement level of 50% is recommended for CR in the cement composite.

• Computers and Concrete
• /
• v.29 no.5
• /
• pp.335-346
• /
• 2022

Geopolymers are an important alternative material supporting recycling, sustainability, and waste management. Durability properties are among the most critical parameters to be investigated; in this study, the durability of manufactured geopolymer samples under the attack of 10% magnesium sulfate and 10% sodium sulfate solution was investigated. 180 cycles of freezing and thawing were also tested. The experimentally obtained results investigate the durability of geopolymer mortar prepared with fly ash (class F) and alkali activator. Three different quarry dust wastes replaced the river sand aggregate: limestone, marble, and basalt powder as fine filler aggregate in three different replacement ratios of 25%, 50%, and 75% to produce ten series of geopolymer composites. The geopolymer samples' visual appearance, weight changes, UPV, and strength properties were studied for up to 12 months at different time intervals of exposure to sulfate solutions to investigate sulfate resistance. In addition, Scanning Electron Microscopy (SEM), EDS, and XRD were used to study the microstructure of the samples. It was beneficial to include quarry waste as a filler aggregate in durability and mechanical properties. The compact matrix was demonstrated by microstructural analysis of the manufactured specimens. The geopolymer mortars immersed in sodium sulfate showed less strength reduction and deterioration than magnesium sulfate, indicating that magnesium sulfate is more aggressive than sodium sulfate. Therefore, it is concluded that using waste dust interrogation with partial replacement of river sand with fly ash-based geopolymers has satisfactory results in terms of durability properties of freeze-thaw and sulfate resistance.

• Journal of the Korean Professional Engineers Association
• /
• v.42 no.3
• /
• pp.47-53
• /
• 2009

Riverbed filtration(RBF) system is used to develop ground water and infiltrated water supplies from permeable sand and gravel deposits. RBF plants are constructed with a reinforced concrete caisson that serves as a wet well pumping station. The lateral well screens are projected horizontally into waterbearing deposits from inside the caisson. Riverbed filtration(RBF) is a low-cost and efficient alternative water treatment for drinking-water applications.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.2
• /
• pp.161-167
• /
• 2008

Optimization of concrete mixing system is very important for the production of quality mixture of concrete and requires very complicated, specialized knowledge as there are a variety of variables that influence the result. One of the methods of optimizing the concrete mixing system is to minimize the volume of cement paste which, in turn, means maximizing the volume of aggregate. The purpose of this study is to determine the minimum volume of cement paste used in the design of concrete mixture and to design the optimum concrete mixing system based on the fluidity of mortar and concrete. In determining the minimum volume of cement paste, experiments of mortar and concrete were performed based on their workability, material segregation and bleeding. Type of aggregate, granularity distribution and sand percentage were used as test parameters and measurements were taken of the distribution of granularity, usage of HRWRA, minimum volume of paste and drying shrinkage and compressive strength of concrete.

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.527-535
• /
• 2001

The watertight property of concrete was examined, that is affected by the sort of self waterproofing admixture and the change of the addition ratio of admixture. Various self waterproofing admixtures were made by changing the mixing ratio of silica fume, zinc stearate and silica sand. The result showed as follows. As the adding ratio of self waterproofing admixture increases, the fluidity is increased and the setting time is delayed. While compressive strength of concrete with self waterproofing admixture A which is currently using is increased until the adding ratio of self waterproofing admixture reached 18kg/㎥ and decreased over 24 kg/㎥, that with self waterproofing admixture B, C and D which are developed are higher than that of A. Absorption is decreased as the adding ratio of self waterproofing admixture and the increasing of age in concrete. Especially, when self waterproofing admixture has a lot of zinc stearate, absorption is decreased manifestly. The property of permeability is similar to that of absorption; permeability is decreased as the adding ratio of self waterproofing admixture and the increasing of age in concrete. Consequently, when the ratio of silica fume, zinc stearate and silica sand in self waterproofing admixture is 1 : 2 : 1 and addition ratio of self waterproofing admixture is 6kg/㎥, the high quality concrete is obtained comparing to the concrete with existent self waterproofing admixture.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.187-194
• /
• 2016

In this research, the influence of low-quality aggregate on engineering properties of concrete was experimentally evaluated. From a series of experiment, the results can be summarized as follow: first, the low-quality aggregate in concrete mixture caused up to 83% of decreased slump. For air content, low-quality aggregate increased air content of concrete mixture. Especially, when sea sand was used, because of the narrow gradation with small size, the air content was significantly increased. The compressive strength of concrete mixtures with low-quality aggregates were decreased up to 29% while some cases showed slightly increased compressive strength at early age. Additionally, the concrete mixture mixed with the exploded debris as a coarse aggregate showed approximately 5 to 20% of decreased compressive strength comparing with high-quality of manufacturing rock. In summary, because of the decreased workability of concrete mixture mixed with low-quality aggregates such as exploded debris, clay, and sea sand, it is concerned that worse quality of the ready mixed concrete, produced with the extra water to compensate the decreased workability.

• Advances in concrete construction
• /
• v.5 no.3
• /
• pp.201-219
• /
• 2017

With the rapid growth in construction sector, it becomes all the more important to assess the amount of Construction and Demolition (C&D) waste being generated and analyze the practices needed to handle and use this waste before final disposal. This serves waste management and disposal issues, paving way to waste utilization in construction industry from the sustainability point of view. C&D waste constitutes a major bulk of total solid waste produced in the world. In this work, an attempt is made to study the performance of concrete using water soaked Recycled Coarse Aggregates (RCA) in replacement levels of 0%, 25%, 50%, 75% and 100% to Natural Coarse Aggregates (NCA). Experiments were designed and conducted to study the performance of RCA based concrete. Further suitable performance enhancement techniques to RCA based concrete were attempted, to achieve compressive strength at least equal to or more than that for no RCA based concrete (control concrete). Performance enhancement study is reported here for 50% and 100% RCA based concretes. All four techniques attempted have given favorable results encouraging use of RCA based concretes with full replacement levels, to adopt RCA based concrete in structural applications, without any kind of concern to the stake holder. Further attempts have also been made to use Recycled Fine Aggregates (RFA) with appropriate modifications to serve as fine aggregates in mortar and concrete. Using RFA blended with river sand fractions as well as RFA with Iron Ore Tailings (IOT) fractions, have given good results to serve as fine aggregates to the extent of 100% replacement levels in mortars and concretes.

• Computers and Concrete
• /
• v.24 no.1
• /
• pp.19-35
• /
• 2019

In this paper, the effect of the type and amount of fibers on the physicomechanical properties of concrete containing fine recycled refractory brick (RRB) and natural aggregate subjected to elevated temperatures was investigated. For this purpose, forta-ferro (FF), polypropylene (PP), and polyvinyl alcohol (PVA) fibers with the volume fractions of 0, 0.25, and 0.5%, as well as steel fibers with the volume fractions of 0, 0.75, and 1.5% were used in the concrete containing RRB fine aggregate replacing natural sand by 0 and 100%. In total, 162 concrete specimens from 18 different mix designs were prepared and tested in the temperature groups of 23, 400, and $800^{\circ}C$. After experiencing heat, the concrete properties including the compressive strength, ultrasonic pulse velocity (UPV), weight loss, and surface appearance were evaluated and compared with the corresponding results of the reference (unheated) specimens. The results show that using RRB fine aggregate replacing natural fine aggregate by 100% led to an increase in the concrete compressive strength in almost all the mixes, and only in the PVA-containing mixes a decrease in strength was observed. Furthermore, UPV values at $800^{\circ}C$ for all the concrete mixes containing RRB fine aggregate were above those of the natural aggregate concrete specimens. Finally, regarding the compressive strength and UPV results, steel fibers demonstrated a better performance relative to other fiber types.

• Structural Engineering and Mechanics
• /
• v.47 no.4
• /
• pp.545-557
• /
• 2013

Disposal of construction wastes poses major challenge to the municipal administration in the developing countries. At the same time new developments in these countries are unscrupulously exploiting the natural resources. The sustainable development requires judicious and careful utilization of natural resources. In this context, reuse of construction and demolition waste can save the global natural resources to greater extent. In this work the bricks and concrete waste from construction sites were crushed to the desired sizes and mixed in various proportions to study its properties in the concrete both in fresh and hardened states. Six mixes of natural and recycled aggregates were used to make the coarse aggregates for the concrete. From each mix nine cylinders were cast, which were tested at 7,14 and 28 days. The properties of concrete with recycled aggregates were compared with the control mix having natural aggregates. The nominal ratio of cement sand and coarse aggregates were kept at 1:2:4 by weight for all mixes. The tests have shown that concrete with recycled aggregates made from old concrete and brick bats provide greater opportunities for reuse of construction wastes in concrete.

• Computers and Concrete
• /
• v.20 no.2
• /
• pp.215-227
• /
• 2017

A finite element model (FEM) for predicting early-age behavior of reinforced concrete (RC) bridge deck slabs with fiber-reinforced polymer (FRP) bars is presented. In this model, the shrinkage profile of concrete accounted for the effect of surrounding conditions including air flow. The results of the model were verified against the experimental test results, published by the authors. The model was verified for cracking pattern, crack width and spacing, and reinforcement strains in the vicinity of the crack using different types and ratios of longitudinal reinforcement. The FEM was able to predict the experimental results within 6 to 10% error. The verified model was utilized to conduct a parametric study investigating the effect of four key parameters including reinforcement spacing, concrete cover, FRP bar type, and concrete compressive strength on the behavior of FRP-RC bridge deck slabs subjected to restrained shrinkage at early-age. It is concluded that a reinforcement ratio of 0.45% carbon FRP (CFRP) can control the early-age crack width and reinforcement strain in CFRP-RC members subjected to restrained shrinkage. Also, the results indicate that changing the bond-slippage characteristics (sand-coated and ribbed bars) or concrete cover had an insignificant effect on the early-age crack behavior of FRP-RC bridge deck slabs subjected to shrinkage. However, reducing bar spacing and concrete strength resulted in a decrease in crack width and reinforcement strain.