• Journal of the Korea Concrete Institute
• /
• v.12 no.1
• /
• pp.45-52
• /
• 2000

The quality of cement mortar products largely depends on various work conditions, specially on the grading and grade shape of aggregates. However, the effect of grading and grade shape on the quality is not considered by both KS codes and production processes, resulting in the increase of the possibility of quality degradation. The objective of this study was to investigate the effect of grading and grade shape on the strength and absorption characteristics of cement mortar products. Flexural and compressive strength increased with the increase of fineness modulus and W/C. The strength increase was measured larger with river sand than with crushed sand. Absorption tended to decrease with the increase of fineness modulus and W/C, but did not affected by the source of sand.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.339-340
• /
• 2009

this study, after examining quality of mortar for different manufacturing stages of recycled sand produced by wet gravity separation system, it was found that the quality of recycled sand was improved greatly after going through the wet gravity separation system.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.223-228
• /
• 1997

In this study, bottom ash, lightweight aggregate, and Expanded Polystyrene was used to lighten the mortar. In order to compensate the reduction of strength caused by lightening, the waste foundry sand produced as solid waste was substituted for fine aggregate. As the device of reducing the ratio of absorption, the procedure of mixture was altered to check the effectiveness of surface coating of porous lightweight aggregate. It was observed over 170kg/$\textrm{cm}^2$ compressive strength at gravity about 1.3, an over 380kg/$\textrm{cm}^2$ at gravity about 1.7. the maximum strength was occurred when 30% of fine aggregate was replaced was replaced with waste foundry sand, and the ratio of absorption was decreased over 10% by changing the procedure of mixture.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.836-841
• /
• 2008

CFRD (Concrete Faced Rockfill Dam) has been world-widely constructed due to a lot of advantages compared with rockfill dam and recently, sand/gravel materials, instead of crushed rock materials, are also utilized as a main rockfill material to overcome geological and environmental problems. In this paper, the process of water infiltration into the originally unsaturated sand/gravel-fill dam is studied using two-dimensional saturated-unsaturated seepage theory. According to the results of seepage analysis, if the effective drainage zone is installed in the dam, the reservoir water infiltrate into the dam along a downward flow path towards the lower drainage area. The main body constructed with sand/gravel materials, therefore, remains unsaturated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.207-214
• /
• 1997

Strength experimental on mortar which use Quenched Blast-Furnace Slag as aggregate was carried our for a fundamental study of application possibility of Quenched Blast-Furnace Slag as aggregate. It gives the following results. The strength of mortar use Quenched Blast-Furnace Slag is decrease as substitution rate is higher. As W/C rate increase, the strength decrease, but the strength decrease of fine aggregate rate 1:3 is lower than 1:2. The relation with fine aggregate is that the amount of fine aggregate is inversely proportional to strength. Th relation with age is proportional to strength and strength rate of going is lower than general mortar in 28 age the change of strength proportionately with W/C rate is that as W/C rate increases, th strength is drop ; it shows that it has same tendency as general mortar sand or crushed sand, but while W/C rate increase the strength is as high as general mortar. The reason can be assumed that water content per unit needed to Quenched Blast-Furance Slag is more than in case of sand. In addition, the relation with substitution rate is that the strength is the strongest at substitution rate 25% and 50% ; that is , sometimes it is higher than mortar which use sand 100%. In addition, long age strength of mortar which use Quenched Blast-Furnace Slag as aggregate is about to be studied in the last.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.350-355
• /
• 1998

Preplaced aggregate concrete in the building fields has recently been used in the partial repair works for damaged reinforced concrete structures, and polymer-modified mortars have been employed as grouting mortars for the preplaced aggregate concrete. The objective of this study is to clear the properties of polymer-modified grouting mortars. Polymer-modified mortars using a polystyrene acrylic(St/Ac) emulsion as grouting mortars for preplaced aggregate concrete are prepared with various mix proportions, and tested for flexural and compressive strengths, adhesion in tension. The flexural strength of emulsion-modified grouting mortars does not give much variation with increasing fly ash replacement for cement and sand-binder ratio. With increasing polymer-binder ratio, the flexural strength and adhesion in tension of St/Ac emulsion-modified grouting mortars increases, become nearly constant or reaches a maximum at a polymer-binder ratio of 5%. From the test results, St/Ac emulsion-modified grouting mortar with a polymer-binder ratio of 5%, a fly ash replacement of 10% for cement and sand-binder ratio of 1.0 is recommended as a grouting mortar for preplaced aggregate concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.99-104
• /
• 2001

Slag product has the possibility as alternative aggregate and sand under the circumstance of natural resource shortage. Copper slag is the by-product produced in process of copper industry. Recycling the slag in construction industry could give positive effects on the environmental preservation. This study presents that the fundamental properties of high strength concrete which used copper slag as alternative sand. Testing factors are concrete's slump, bleeding, air contents and compressive strength. The results of this study are as follows. (1) Mixing of W/C 30%, substitution rate 25% shows the best slump. As substitution rates are going up, concrete slump is uprising and air contents are downsizing. (2) The bleeding of concrete becomes more serious as substitution rates are going up. (3) The best compressive strength of copper slag concrete is achieved in mixing of W/C 30%, substitution rate 25%.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.15-18
• /
• 2003

Development of the construction industry generally exhausts natural aggregate. Hence it is problem to the lack of supply and quality deterioration, so the resource saving and protection of environment is made an effort through recycling by-product. This study presents that fundamental properties of concrete which used cooper slag as alternate sand of low fineness modulus and plan of cooper slag as concrete aggregate. Testing factors are concrete's slump, air contents, unit weight and compressive strength. The results of this study are as follows; (1) Concrete slump is generally satisfied with the condition but is inferior to the others in substitution rates 30%. Also air contents are 3.1-4.1% and go up according to increase substitution rate. (2) Unit weight increase in 1.1% as the mixing ratio of cooper slag argument 10%. (3) compressive strength of cooper slag concrete is similar to plain and especially higher 11-15% in W/C 45%, 50%. So it seems that aggregate mixed cooper slag is suitable to low water-cement ratio mixture.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.5
• /
• pp.69-77
• /
• 2004

FRP rebar has low bond performance than steel rebar. Usually, FRP rebar has about 60% of bond strength of steel rebar. Without adequate bond to concrete, the full composite action between reinforcement and concrete matrix can not be achieved. Therefore, FRP rebars must also have surface deformations that provide good bond to concrete. The purpose of this research was decided an optimum surface deformation patterns through bond test of FRP rebar. Eighteen surface deformation patterns of FRP rebar with widely different geometries were investigated. Based on the test results, we established optimum surfale deformation pattern. Bond tests were performed for three types of surface deformation patterns of FRP rebar including sand coated rebar, ribbed rebar, and wrapped and sand coated rebar that commercially available, and two types of FRP rebar including CFRP, GFRP rebars that optimum surface deformation pattern is applied. According to bond test results, FRP rebars that optimum surface deformation pattern is applied were found to have better bond strength with concrete than currently using FRP rebar.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.576-580
• /
• 2001

The amount of the waste foundry sand(WFS) produced in Korea is over 700,000 ton per year, but most WFS buries itself and only 5~6% or total WFS is recycled in the way or mixing as fine aggregate for construction materials. A bY-product, WFS produced from a foundry may affect our environmental contamination if it is discharged without proper waste disposal in Korea. Therefore in this study, we performed the fundamental research about specific gravity, absorption, grading curve, finesse modulus of WFS, different aggregates and the flow and the compressive strength of mortar with WFS replaced as fine aggregate, the workability and compressive strength of concrete with WFS as fine aggregate aimed at the specified strength of 270 kgf/$\textrm{cm}^2$, and then optimum mix proportion of concrete was determined