• Journal of Electrical Engineering and Technology
• /
• 제8권4호
• /
• pp.872-878
• /
• 2013

In industrial control systems, flow measurement is a very important issue. It is frequently needed to calculate how much total fluid or gas flows through a cross-section. Flow volume measurement tools use simple sampling or rectangle methods. Actually, flow volume measurement process is an integration process. For this reason, measurement systems using instantaneous sampling technique cause considerably high errors. In order to make more accurate flow measurement, numerical integration methods should be used. Literally, for numerical integration method, Rectangular, Trapezoidal, Simpson, Romberg and Gaussian Quadrature methods are suggested. Among these methods, trapezoidal rule method is quite easy to calculate and is notably more accurate and contains no restrictive conditions. Therefore, it is especially convenient for the portable flow volume measurement systems. In this study, the volume measurement of air which is flowing through a cross-section is achieved by using PLC ladder diagram. The measurements are done using two different approaches. Trapezoidal rule method is proposed to measure the flow sensor signal to minimize measurement errors due to the classical sampling method as a different approach. It is concluded that the trapezoidal rule method is more effective than the classical sampling.

• 한국산업보건학회지
• /
• 제7권1호
• /
• pp.33-48
• /
• 1997

Korean diffusive sampler (KDS) and charcoal tube (CT) were used for sampling n-hexane, trichloroethylene and toluene in air KDS was made by Department of Environmental Health, SNU-SPH in 1995. Surveys were conducted at ten industrial plants with organic solvents. The relationship between two sampling methods was examined by linear regression analysis, and concentrations by two sampling methods were compared using paired t-test. The results are as follows: 1. The geometric means by CT and KDS methods were 3.26ppm and 3.32ppm for n-hexane, 5.07ppm and 6.34ppm for toluene, and 7.18ppm and 7.90ppm for toluene, respectively. There was no significant difference between results by CT and KDS methods in three organic vapors (p>0.05). When linear regression analysis was performed, two sampling methods were highly related ; correlation coefficients were 0.98, 0.90 and 0.96 for n-hexane, toluene and trichloroethylene, respectively. 2. Airborne concentrations of n-hexane (n=21) were below 0.5 TLV level. The GM by two methods were almost same (3.09 ppm). And there was no significant difference between results by two methods (p>0.05). 3. Since toluene and trichloroethylene concentrations showed several levels, appropriate sampling rates were applied for each level. The GM of toluene concentrations by two methods at 0.5 TLV level were 3.75ppm and 5.48ppm. The KDS method overestimated the toluene concentrations at 0.5 TLV level (p<0.05). The GM values of toluene concentrations at 1 TLV level were 31.80ppm and 25.38ppm and at 2 TLV level were 64.13 ppm and 51.37 ppm. The KDS method underestimated concentration at both level (p<0.05). For trichloroethylene, the GM at 0.5 TLV level were 4.97 ppm and 7.11ppm. The KDS method overestimated the concentration of trichloroethylene (p<0.05). In conclusion, concentrations of three organic vapors measured by CT and KDS were not significantly different and results by two methods were highly related. But at contain concentrations, the levels by method were significantly different. Therefore, it is suggested that sampling rate of KDS should be studied simultaneously using CT method for organic vapors.

• 한국해양공학회지
• /
• 제28권3호
• /
• pp.254-259
• /
• 2014

The infrared signature of a ship is largely influenced by the ocean environment of the operating area, which has been known to cause large changes in the signature. As a result, the weather condition has to be clearly set for an analysis of the infrared signatures. It is necessary to analyze meteorological data for all the oceans where the ship is supposed to be operated. This is impossibly costly and time consuming because of the huge size of the data. Therefore, the creation of a standard environmental variable for an infrared signature research is necessary. In this study, we compared and analyzed sampling methods to represent ocean data close to the Korean peninsula. In order to perform this research, we collected ocean meteorological records from KMA (Korea Meteorological Administration), and sampled these in numerous ways considering five variables that are known to affect the infrared signature. Specifically, a simple random sampling method for all the data and 1-D, 2-D, and 3-D stratified sampling methods were compared and analyzed by considering the mean square errors for each method.

• 한국산림과학회지
• /
• 제109권3호
• /
• pp.291-299
• /
• 2020

본 연구는 경상북도 봉화군 춘양면 애당리 수확 벌채 지역을 대상으로 다양한 표본추출방법을 적용하여 재적을 산출한 후 실제 벌채량 및 설계서상의 재적 값과의 비교를 통해 보다 정확하고 비용 효율적인 표본추출방법을 제시하고자 수행하였다. 연구에 사용된 표본추출방법으로는 1) 임의추출법, 2) 계통추출법, 3) 선상추출법을 적용하였으며, 각 표본추출방법별로 이동시간, 추정된 재적평균의 표본 오차율, 조사시간, 조사원 규모, 시간당 임금, 표본점 개수 등을 이용하여 표본추출방법에 대한 산림조사의 비용 효율성을 분석하였다. 각 표본추출방법별로 10개의 표본점을 추출하였으며, Bootstrap 기법을 이용하여 표본 강도의 타당성을 검증하였다. 분석결과, 선상추출법이 임의 및 계통추출법보다 실측된 재적 값과의 재적 편차가 상대적으로 가장 적은 것으로 나타났고, 산림 조사 비용 측면에서는 목표 표준오차율에 상관없이 임의추출법을 활용한 산림조사가 조사비용이 가장 낮은 것으로 나타났다. 본 연구결과에 따르면, 선상추출법과 임의추출법을 통한 산림조사 방법이 계통추출법을 이용한 방법보다 비용 효율적이며 재적의 정확도가 높은 것으로 나타났다. 하지만 사례 연구의 특성상, 연구에서 분석된 결과의 일반화에는 한계가 있어, 향후 국내의 다양한 지역을 대상으로 동일한 방법의 연구가 진행된다면, 국내 산림의 환경적 특성을 반영한 표본추출방법이 제시될 것으로 기대된다.

• 한국통신학회논문지
• /
• 제32권12A호
• /
• pp.1286-1295
• /
• 2007

본 논문은 SDR(software-defined radio) 시스템에 적용할 수 있는 기술로서, 대역통과 샘플링(bandpass sampling)이론을 사용하여 N개 RF 신호를 하나의 통신기기에서 직접 하향변환(down-conversion)할 때 요구되는 유효 샘플링 주파수 영역(valid sampling frequency range) 및 최소 샘플링 주파수를 찾는 방법을 제안하였다. 이 방식은 IF단의 신호배치에 대한 모든 순열을 고려하면서도 기존의 방식보다 효율적이며 복잡성이 낮은 방식을 새롭게 고안하여 N개의 신호에 대하여 수식을 유도하고 일반화 하였으며 컴퓨터 모의실험(simulation)을 통해 이 수식들을 증명하였다. 그리고 제안한 알고리즘은 샘플링 주파수를 결정할 때 인접 IF(intermediate frequency) 신호간의 보호대역(guard-band)이 고려되어 실제적인 하드웨어 설계 측면에 도움이 되도록 하였다. 또한 기존의 방식과의 비교를 통해 그 복잡성(complexity)및 정확성에서도 우수한 성능을 보여주었다.

• Communications for Statistical Applications and Methods
• /
• 제14권2호
• /
• pp.345-353
• /
• 2007

A Bayesian estimation of the Nakagami-m fading parameter is developed. Bayesian estimation is performed by Gibbs sampling, including adaptive rejection sampling. A Monte Carlo study shows that the Bayesian estimators proposed outperform any other estimators reported elsewhere in the sense of bias, variance, and root mean squared error.

• Communications for Statistical Applications and Methods
• /
• 제12권1호
• /
• pp.11-18
• /
• 2005

Assume that the life times of the units under test follow the Rayleigh distribution and the test is terminated at a pre assigned time. Acceptance sampling plans are developed for this situation. The minimum sample size necessary to ensure the specified average life are obtained and the operating characteristic values of the sampling plans and producer's risk are given. An example is given to illustrate the methodology.

• Communications for Statistical Applications and Methods
• /
• 제12권1호
• /
• pp.181-189
• /
• 2005

This paper suggest a method of inclusion probability proportional to size sampling that provides a non-negative and stable variance estimator. The sampling procedure is quite simple and flexible since a sampling design is easily obtained using mathematical programming. This scheme appears to be preferable to Nigam, Kumar and Gupta's (1984) method which uses a balanced incomplete block designs. A comparison is made with their method through an example in the literature.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.46.4-46
• /
• 2002

This study was motivated how it might be possible to validate structured sampling with orthogonal array for optimal design of a pin. The Taguchi method by orthogonal array, one of the structured sampling methods, has much advantage that is row cost and time saving for experiments. But this method has been applied in limited areas especially for mechanical problems. In this study, we experimented whether the structured sampling is useful for applying optimal design of mechanical elements. For the experiment, we first set up a mechanical problem which was related to determining optimal parameters associated a pin's crack occurred inside a hole. We, then, calculated combination of...

• 한국환경보건학회지
• /
• 제13권1호
• /
• pp.63-65
• /
• 1987

A study on detection rates of acid-fast bacteria in urine by three sampling methods was performed on 898 cases randomly sampled from peoples who visited Dr. Chung's Health Lab. from January to December, 1983. Positive rate by 5 times sampling of motring urine was 7.0% and 12.5% higher than that of 24 hours sampling. Therefore, 5 times sampling of morning urine method was considered to be desirable method for the test of ambulatory cases.