• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.2
• /
• pp.54-60
• /
• 1987

This paper describes on the distribution of the vibration and the noise produced on a skipjack pole and line training ship M/S Pusan 403 (243GT, 1,000ps) under the cruising or drifting condition. The vibration and the noise level were measured by use of protable vibration analyzer (B and K 3513) and sound level meter (B and K 2205), and so the vibration level was converted into dB unit. The check points were set through every decks and around important places of the ship. The results obtained can be summarized as follows: 1. The vibration and the noise level 1) On the main deck, both the vibration and the noise level were highest at the vertically above the main engine, whereas the vibration level was the lowest in the bow store and the noise level beneath the bridge. 2) Under cruising condition, the vibration level around the cylinder head of main engine, port side of the engine room, on the shaft tunnel was 80, 67, 65 dB and the noise level 104, 87, 86 dB, respectively. 3) The vibration level on the vertical line passing through the bridge was the highest at the orlop deck with 60 dB and the lowest on the bridge deck with 55 dB, whereas the noise level the highest at the compass deck with 75 dB and the lowest at the orlop deck with 53 dB. 4) The vibration and the noise level on the open decks were the highest with 65 dB and 84 dB on the boat deck, whereas the vibration level was the lowest at the lecture room with 51 dB and the noise level the lowest at the fore castle deck with 57 dB. 5) On the orlop decks, both the vibration and the noise level were the highest at the engine room with 65 dB and 85 dB, and the lowest at bow store with 54 dB and 52 dB, respectively. Comparing with the vibration level and the noise level, the vibration level was higher than the noise level in the bow part and it was contrary in the stern part of the ship. 2. Vibration analysis 1) The vibration displacement and the vibration velocity were the greatest at the cylinder head of main engine with 100$\mu$m and 11mm/sec, and were the smallest at the compass deck with 3$\mu$m and 0.07mm/sec. They were also attenuated rapidly around the frequency of 100Hz and over. 2) The vibration acceleration was the greatest at the cylinder head with the main frequency of 1KHz and the acceleration of 1.1mm/sec super(2), and the smallest at the compass deck with 30KHz and 0.05mm/sec super(2).

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.2
• /
• pp.169-181
• /
• 2007

Statement of problem: Titanium is well known as a proper metal for the dental restorations, because it has an excellent biocompatibility, resistance to corrosion, and mechanical property. However, adhesion between titanium and dental porcelains is related to the diffusion of oxygen to the reaction layers formed on cast-titanium surfaces during porcelain firing and those oxidized layers make the adhesion difficult to be formed. Many studies using mechanical, chemical and physical methods to enhance the titanium-ceramic adhesion have been actively performed. Purpose: This study meant to comparatively analyse the adhesion characteristics depending on different titanium surface coatings after coating the casts and wrought titanium surfaces with Au and TiN. Material and method: In this study, the titanium specimens (CP-Ti, Grade 2, Kobe still Co. Japan) were categorized into cast and wrought titanium. The wrought titanium was cast by using the MgO-based investment(Selevest CB, Selec). The cast and wrought titanium were treated with Au coating($ParaOne^{(R)}$., Gold Ion Sputter, Model PS-1200) and TiN coating(ATEC system, Korea) and the ultra low fusing dental porcelain was fused and fired onto the samples. Biaxial flection test was done on the fired samples and the porcelain was separated. The adhesion characteristics of porcelain and titanium after firing and the specimen surfaces before and after the porcelain fracture test were observed with SEM. The atomic percent of Si on all sample surfaces was comparatively analysed by EDS. In addition, the constituents of specimen surface layers after the porcelain fracture and the formed compound were evaluated by X-ray diffraction diagnosis. Result: The results of this study were obtained as follows : 1. The surface characteristics of cast and wrought titanium after surface treatment(Au, TiN, $Al_2O_3$ sandblasting) were similar and each cast and wrought titanium showed similar bonding characteristics. 2. Before and after the biaxial flection test, the highest atomic weight change of Si component was found in $Al_2O_3$ sandblasted wrought titanium(28.6at.% $\rightarrow$ 8.3at.%). On the other hand, the least change was seen in Au-Pd-In alloy(24.5at.% $\rightarrow$ 9.1at.%). 3. Much amount of Si components was uniformly distributed in Au and TiN coated titanium, but less amount of Si's was unevenly dispersed on Al2O3 sandblasting surfaces. 4. In X-ray diffraction diagnosis after porcelain debonding, we could see $Au_2Ti$ compound and TiN coating layers on Au and TiN coated surfaces and $TiO_2$, typical oxide of titanium, on all titanium surfaces. 5. Debonding of porcelain on cast and wrought titanium surface after the biaxial flection is considered as a result of adhesion deterioration between coating layers and titanium surfaces. We found that there are both adhesive failure and cohesive failure at the same time. Conclusion: These results showed that the titanium-ceramic adhesion could be improved by coating cast and wrought titanium surfaces with Au and TiN when making porcelain fused to metal crowns. In order to use porcelain fused to titanium clinically, it is considered that coating technique to enhance the bonding strength between coating kKlayers and titanium surfaces should be developed first.

• Clinical and Experimental Pediatrics
• /
• v.51 no.3
• /
• pp.267-275
• /
• 2008

Purpose : To determine whether primary snoring could be distinguished from obstructive sleep apnea syndrome (OSAS) by clinical evaluation and symptom scores. Methods : 56 snoring and 20 asymptomatic subjects were recruited and polysomnography was used to confirm that there were 39 OSAS, 17 primary snoring, and 20 control subjects. We evaluated the size of the childrens adenoids and tonsils. Parents completed sleep disordered breathing scale (SDBS) and obstructive sleep apnea 18 (OSA-18) questionnaires for use as symptom scores, as well as an attention deficit hyperactivity disorder rating scale-IV (ADHD RS-IV). Results : There were no differences between primary snoring and OSAS in terms of tonsil and adenoid size, SDBS ($9.4{\pm}4.6\;vs\;10.8{\pm}4.5$), and OSA-18 score ($61.1{\pm}25.1\;vs\;71.2{\pm}8.4$). The patients with OSAS ($15.8{\pm}7.9$) and PS ($22.2{\pm}9.4$) had a higher ADHD RS-IV score than the control subjects ($2.9{\pm}3.3$). There was no difference in the ADHD RS-IV scores of patients with primary snoring and OSAS. Conclusion : We confirmed that clinical evaluation could not distinguish OSAS and primary snoring. In addition, our study suggests that primary snoring as well as OSAS is associated with attention deficit hyperactivity disorder.

• The Korean Journal of Pharmacology
• /
• v.26 no.1
• /
• pp.13-23
• /
• 1990

Methylene Blue (MeB) and gentian violet $(10^{-6}{\sim}10^{-4}\;M)$ produced contractions in isolated thoracic aortic preparations of rabbits in a dose-dependent fashion, while other dyes, evans blue and eosine yellowish, did not affect the basal tension in the same range of doses. Porcine mesenteric arterial rings also responded to MeB with dose-dependent contractions. Single dose of $10^{-4}$ M MeB produced a biphasic response: contraction followed by relaxation. The contraction developed slowly within $2{\sim}4$ min and peaked in about 20 minutes and then slowly relaxed to the basal level. Tyramine $(10^{-4}\;M)$ also induced contraction but it developed faster and was more persistent than that of MeB. While the tyramine-induced tension was reproducible, the MeB-induced one wat not reiterable until 3 to 5 hours after washing out the MeB. Adding $10^{-4}$ M MeB further potentiated the contraction induced by $10^{-4}$ M tyramine. However, the MeB contraction was not affected by further addition or tyramine. Both tyramine- and MeB-induced tensions were abolished or significantly inhibited by pretreatment with various drugs acting on the sympathetic nervous system. The tyramine-induced tension was more sensitive to guanethidine and 6-hydroxydopamine than the MeB-induced tension, while the latter was more sensitive to $Ca^{2+}-free$ PSS and reserpine. But they have similar sensitivity to prazosin. The MeB-induced tension was significantly inhibited but not abolished by 6-hydroxydopamine pretreatment. However, either tyramine or 6-hydroxydopamine could not affect the basal tension of the ring that MeB once had been tested. These results suggest that MeB-induced contractions of rabbit thoracic aorta and porcine mesenteric artery result from a release of endogenous norepinephrine from adrenergic nerve endings and are dependent in part on extracellular calcium, and that the potency of MeB to release or to deplete norepinephrine is greater than that of either tyramine or 6-hydroxydopamine.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.1
• /
• pp.33-43
• /
• 2003

The midwater pair trawl which is being used at present in Korea have several problems. Firstly, it is difficult to control the net height on high towing speed. Secondly, net breaking often occurs owing to floats and thirdly, the volume of net on the net drum is so large. This study is aiming for examining the possibility of application for the Korean midwater pair trawl through the model experiment of non-float midwater pair trawl. The model of non-float midwater pair trawl was manufactured as 1/100 of the full scale net which is being used in bottom pair trawl for 850ps class considering the Tauti's Similarity law. The model experiment was carried out to analyze the opening efficiency according to the variation of lower warp length and the opening efficiency was investigated between th proto type and non-float type. The results obtained can be summarized as follows ; 1. The hydrodynamic resistance of non-float type was about 10~20% smaller than that of the proto type and it increased about 1ton according to the increase of dL at the condition of the same flow speed. The resistance acting on the lower warp decreased about 5% but that of the upper warp increased according to the increase of lower warp length (dL) at the condition of the same flow speed. 2. The net height of the non-float type decreased almost linearly according as the increased of flow speed and it increased in a logarithmic functional form with the increase of the lower warp length at the condition of the same flow speed. On the decreasing rate of the net height, the non-float type was lower than the proto type and the difference of the decreasing rate was about 12% at 3.0 knot, 25% at 4.0 knot, 25% at 4.0 knot respectively when dL was 30m. 3. The net width of non-float type was not varied so much as only 2m range and was larger than that of proto type. 4. The mouth area of non-float type decreased in a exponential functional form. On the decreasing rate of the mouth area, the non-float type was lower than the proto type. The filtering volume increased in a logarithmic functional form with increasing flow speed and the filtering volume of proto type decreased steeply over 3.0knot, but that of non-float type increased until 4.0knot. 5. The optimal length of lower warp was when the value of dL was about 30m and the optimal position of front weight was at the connection point of four net pendants.

• Food Science of Animal Resources
• /
• v.24 no.4
• /
• pp.349-354
• /
• 2004

Stress-susceptible pigs have been known as the porcine stress syndrome (PSS), swine PSS, also known as malignant hyperthermia (MH), is characterized as sudden death and production of poor meat quality such as PSE (pale, soft and exudative) meat after slaughtering. PSS and PSE meat cause major economic losses in the pig industry. A point mutation in the gene coding for the ryanodine receptor (RYR1) in porcine skeletal muscle, also known calcium (Ca$^{2+}$) release channel, has been associated with swine PSS and halothane sensitivity. We used the PCR-RFLP(restriction fragment length polymorphism) and PCR-SSCP (single strand conformation polymorphism) methods to detect the PSS gene mutation (C1843T) in the RYR1 gene and to estimate genotype frequencies of PSS gene in Korean pig breed populations. In PCR-RFLP and SSCP analyses, three genotypes of homozygous normal (N/M), heterozygous carrier (N/n) and homozygous recessive mutant (n/n) were detected using agarose or polyacrylamide gel electrophoresis, respectively. The proportions of normal, carrier and PSS pigs were 57.1, 35.7 and 7.1％ for Landrace, 82.5, 15.8 and 1.7％ far L. Yorkshire, 95.2, 4.8 and 0.0％ for Duroc and 72.0, 22.7 and 5.3％ for Crossbreed. Consequently, DNA-based diagnosis for the identification of stress-susceptible pigs of PSS and pigs producing PSE meat is a powerful technique. Especially, PCR-SSCP method may be useful as a rapid, sensitive and inexpensive test for the large-scale screening of PSS genotypes and pigs with PSE meat in the pork industry.y.

• Korean Journal of Environmental Agriculture
• /
• v.6 no.2
• /
• pp.53-65
• /
• 1987

The study was performed to investigate the effect of gaseous emissions of sulfur dioxide and hydrogen fluoride on the growth of rice plants under stressed field conditions consisting of 88 industrial plants operating with 285 smoke stacks emitting pollutants. As for the relationship between yields and yield components it is believed that the panicles per hill is the single most important component affecting the rate of yield of the rice plant. Based on the standard partial regression coefficient analysis, panicles per hill has the largest contribution to yield and the average contribution of 54%. Other components such as spikelets per panicle, percent fertility and 1000 grain weight are also contributing factors to yield, although far less so. Fluorine content in the leaf appear to have more negative effect on panicles per hill, percent fertility and subsequent overall yield than does sulfur content in the leaf. It is constantly observed and interesting to note that fluorine and sulfur content in the leaf appears to have no effect on spikelets per panicle and 1000 grain weight. Reduction in yield seems to be affected mainly by panicles per hill which are, in turn, affected more by fluorine content in the leaf as demonstrated by the standard partial coefficient analysis. Regarding the prediction sum of the square of the regression equation, the lowest value was found when nine variables were used for the analysis. The variables taken into consideration were the monthly sulfur and fluorine content in the leaf as well as the monthly percent of leaf damage during the months of June, July and August. A significant correlation is found between the actual and predicted yields by the regression equations selected as a result of a prediction sum of the square analysis.

• Journal of Food Hygiene and Safety
• /
• v.38 no.2
• /
• pp.37-45
• /
• 2023

The surge in food delivery systems during the coronavirus 2019 pandemic necessitated this study of heavy metal migration from food contact materials (FCMs). A total of 104 samples of FCMs, comprising 51 polypropylene (PP), 21 polyethylene (PE), and 32 polystyrene (PS) samples of six different types of FCMs (containers, covers, table utensils, cups, pouches, and wrappers) used for food delivery distributed in Korea, were collected and investigated for migration of three heavy metals (Pb, Cd, and As) using inductively coupled plasma-mass spectrometry (ICP-MS) to determine whether they complied with Korea's Standards and Specifications for Utensils, Containers, and Packages. Acetic acid (4%, v/v) was used as the food simulant, and tests were performed at 100℃ (in harsh conditions) for 30 min. Linearity of Pb, Cd, and As showed acceptable results with a coefficient of determination (R²) value of 0.9999. Limit of detection (LOD) and limit of quantification (LOQ) of Pb, Cd, and As were 0.001, 0.001, and 0.001 ㎍/L and 0.002, 0.003, and 0.003 ㎍/L, respectively. Accuracy and precision results complied with the criteria presented in the European Commission Joint Research Centre guidelines. The average concentration of Pb, Cd, and As migration detected in a total of 104 samples was 0.009-0.260 ㎍/L, which was very low compared with the migration specification set in the Standards and Specifications for Utensils, Containers, and Packages. The maximum level of Pb corresponded to 0.23% of the migration limit. There were no samples exceeding the limit. Thus, this study confirmed that the heavy metal contents of FCMs used for delivery food distributed in Korea were safely managed. The data from this study represent an invaluable source for science-based safety management of hazardous heavy metals migrating from FCMs used in the food delivery industry.

• Tuberculosis and Respiratory Diseases
• /
• v.45 no.4
• /
• pp.813-822
• /
• 1998

Background: Extubation is recommended to be performed at minimum pressure support (PSmin) during the pressure support ventilation (PSV). In field, physicians sometimes perform additional 1 hr T-piece trial to the patient at PSmin to reduce re-intubation risk. Although it provides confirmation of patient's breathing reserve, weaning could be delayed due to increased airway resistance by endotracheal tube. Methods: To investigate the effect of additional 1 hr T-piece trial on weaning outcome, a prospective study was done in consecutive 44 patients who had received mechanical ventilation more than 3 days. Respiratory mechanics, hemodymic, and gas exchange measurements were done and the level of PSmin was calculated using the equation (PSmin=peak inspiratory flow rate $\times$ total ventilatory system resistance) at the 15cm $H_2O$ of pressure support. At PSmin, the patients were randomized into intervention (additional 1 hr T-piece trial) and control (extubation at PSmin). The measurements were repeated at PSmm, during weaning process (in cases of intervention), and after extubation. The weaning success was defined as spontaneous breathing more than 48hr after extubation. In intervention group, failure to continue weaning process was also considered as weaning failure. Results: Thirty-six patients with 42 times weaning trial were satisfied to the protocol. Mean PSmin level was 7.6 (${\pm}1.9$)cm $H_2O$. There were no differences in total ventilation times (TVT), APACHE III score, nutritional indices, and respiratory mechanics at PSmin between 2 groups. The weaning success rate and re-intubation rate were not different between intervention group (55% and 18% in each) and control group (70% and 20% in each) at first weaning trial. Work of breathing, pressure time product, and tidal volume were aggravated during 1 hr T-piece trial compared to those of PSmin in intervention group ($10.4{\pm}1.25$ and $1.66{\pm}1.08$ J/L in work of breathing) ($191{\pm}232$ and $287{\pm}217$cm $H_2O$ s/m in pressure time product) ($0.33{\pm}0.09$ and $0.29{\pm}0.09$ L in tidal volume) (P<0.05 in each). As in whole, TVT, and tidal volume at PSmin were significantly different between the patients with weaning success ($246{\pm}195$ hr, $0.43{\pm}0.11$ L) and the those with weaning failure ($407{\pm}248$ hr, $0.35{\pm}0.10$L) (P<0.05 in each). Conclusion : There were no advantage to weaning outcome by addition of 1 hr T-piece trial compared to prompt extubation to the patient at PS min.

• Sleep Medicine and Psychophysiology
• /
• v.17 no.2
• /
• pp.100-108
• /
• 2010

Objectives: "Internet-addiction" came into common use not only in clinical setting but also in everyday life. But, pathophysiology and diagnostic criteria of the internet addiction remain unknown. Because adolescents are in developing period, they might be vulnerable to the internet addiction, depression and sleep-related problem. The objectives of this study were to investigate the characteristics of internet addiction and its association with sleep pattern and depression in Korean adolescence. Methods: Subjects were 799 middle and high school students in Seoul, Korea. We administered a self-reported questionnaire including socio-demographic data, Korean versions of Young's Internet Addiction Scale (YIAS), Pittsburgh Sleep Quality Index (PS-QI), the Center for Epidemiologic Studies for Depression Scale (CES-D) and questions about internet using patterns. Data of 696 subjects were included in analysis. Chi-square tests were used to analyze proportional differences, and ANOVA with post-hoc tests were used to analyze differences among groups. Partial correlation analyses were performed to analyze the correlation of internet addiction with other variables (two-tailed, p<0.05). Results: Of the 696 participants (grade 2 of middle school; M2 135 vs. grade 1 of high school; H1 238 vs. grade 2 of high school; H2 323), 2.0% (n=14) were internet-addicted (IA), 27.7% (n=193) were over-using (OU) and 70.3% (n=489) were not-addicted (NA). The mean scores of YIAS, PSQI and CES-D scores were 35.24${\pm}$12.78, 5.53${\pm}$3.04 and 16.72${\pm}$8.69, respectively. In higher grade students, average total sleep time was shorter (M2 426.20${\pm}$67.68 min. vs. H1 380.47${\pm}$62.57 min. vs. H2 354.67${\pm}$73.37 min., F=51.909, p<0.001), and PSQI (4.69${\pm}$3.14 vs. 5.42${\pm}$3.15 vs. 5.97${\pm}$2.83, F=8.871, p<0.001) CES-D (13.53${\pm}$8.37 vs. 16.96${\pm}$8.24 vs. 17.87${\pm}$8.84, F=12.373, p<0.001) scores were higher than those of lower grade students. Comparing variables among IA, OU and NA groups, computer using time not for study (96.36${\pm}$63.31 min. vs. 134.92${\pm}$86.79 min. vs. 213.57${\pm}$136.87 min., F=34.287, p<0.001) and portable device using time not for study (84.22${\pm}$79.11 min. vs. 96.97${\pm}$91.89 min. vs. 152.31${\pm}$93.64 min., F= 5.400, p=0.005) were different among groups. PSQI (5.26${\pm}$2.97 vs. 6.08${\pm}$2.97 vs. 7.50${\pm}$4.41, F=8.218, p<0.001) and CES-D scores (15.40${\pm}$8.08 vs. 19.05${\pm}$8.42 vs. 30.43${\pm}$13.69, F=32.692, p<0.001) were also different among groups. YIAS score were correlated with computer using time not for study (r=0.356, p<0.001) and portable device using time not for study (r= 0.136, p<0.001). PSQI score (r=0.237, p<0.001) and CES-D score (r=0.332, p<0.001). YIAS score and PSQI score (r=0.131, p= 0.001), YIAS and CES-D score (r=0.265, p<0.001), PSQI score and CES-D score (r=0.357, p<0.001) were correlated each other. Conclusion: These results suggested that adolescents' internet-addiction was correlated with not only computer and portable device using time not for study but also depression and sleep-related problems. We should pay attention to depression and sleep-related problems, when evaluating internet-addiction in adolescents.