• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.392-399
• /
• 2005

Shear modulus (or rigidity) of dam material is an important parameter which can be directly associated with the deformation of dam. Seepage or leakage of water can cause the defects or cracks of dam body. The existence of cracks and rigidity of dam body are decisive information for the estimation of dam safety. Rigidity of material is mainly determined from S-wave velocity and the defects of dam body can be detected by seismic reflection survey. Therefore, seismic reflection survey will be a desirable method which can give a solution about dam safety problem. Among various physical properties of dam body, S-wave velocity is the most important information but it is not easy to get the information. In this study, diverse measuring techniques of S-wave reflection survey were attempted to get the information about S-wave velocity of dam body. Ultimately, S-wave velocity could be estimated by the analysis of SH reflection events which can be easily observed in shot gather data obtained from SH measuring technique. Meanwhile, P-wave reflection survey was also performed at the same profile. P-beam radiation technique which can reduce the surface waves and reinforce the P-wave reflection events was applied for giving a help to analyse P-wave velocity. In the end, P-and S-wave velocity, Vs/Vp, Poisson's ratio distribution of the vertical section under the profile could be acquired.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2007년도 공동학술대회 논문집
• /
• pp.75-79
• /
• 2007

To investigate the shear-wave velocity structures of the Korean peninsula, exploded seismic signals were recorded for 120 s along a 294-km WNW-ESE line and 150 s along a 335-km NNW-SSE line in 2002 and 2004, respectively. First arrival times of shear wave were inverted to derive the velocity tomograms. Initial shear-wave 1-D models were built using the initial P-wave velocity models used by Kim et al. and $V_p/V_s$ ratios of the IASP91 model. The raypaths indicate existence of mid-crust interfaces at the depth of 2-3 km and 16 km. The deepest significant interface corresponding to the Moho discontinuity varies in depth from 32 km to 36 km. The refraction velocity along the interface varies from 4.4 km/s to 4.6 km/s. The velocity tomograms also indicate existence of a low-velocity zone at the depth of 7.8 km under the Okchon fold belt.

• The Journal of the Acoustical Society of Korea
• /
• 제26권1E호
• /
• pp.33-38
• /
• 2007

Compressional wave velocity and shear wave velocity were measured for gassy sediments collected from Jinhae Bay, Korea. To distinguish inhomogeneities of gassy sediments, Computed Tomography (CT) was carried out for gassy sediment using CT Scanner. The cored sediments are composed of homogeneous and soft mud (greater than $8{\Phi}$ in mean grain size) containing clay content more than 50%. In depth interval of gassy sediments, compressional wave velocity is significantly decreased from 1480m/s to 1360m/s, indicating that the gas greatly affects compressional wave velocity due to a gas and/or degassing cracks. Shear wave velocity shows a slight increasing pattern from ${\sim}55\;m/s$ in the upper part of the core to ${\sim}58\;m/s$ at 320 cm depth, and then decreases to ${\sim}54\;m/s$ in the lower part of the core containing a small amount of gas. But shear wave velocity in the gassy sediments is slightly greater than that of non-gassy sediments in the upper part of the core. Thus, the Vp/Vs ratio is decreased (from 30 to 25) in gas charged zone. The Vp/Vs ratio is well correlated with shear wave velocity, but no correlation with compressional wave velocity. This suggests that low concentrations of gas have little affects on shear wave velocity. By CT images, the gas in the sediments is mostly concentrated around inner edge of core liner due to a long duration after sediment collection.

• 비파괴검사학회지
• /
• 제19권4호
• /
• pp.259-269
• /
• 1999

최근 초음파속도법과 충격반향기법 등과 같이 탄성파를 이용한 비파괴검사 방법이 콘크리트의 강도나 탄성계수를 결정하는데 유용하게 사용되고 있다. 하지만 탄성파 속도에 영향을 미치는 다양한 인자들이 고려되지 않은 상태에서 비파괴검사가 행해지고 있어 실제로 만족할 만한 결과를 주지 못하고 있다. 이 연구에서는 다양한 영향인자들 중에서 특히 콘크리트의 수분함유량이 종파 속도에 미치는 영향정도를 실험을 통해 조사하였다. 콘크리트 내부의 수분함유량이 감소하면, 즉 콘크리트가 건조해지면 종파 속도는 점점 감소하며, 충격반향기법에 의해 측정된 막대파 속도가 초음파 속도보다 수분의 영향을 더 많이 받는 것으로 나타났다. 또한 기건양생하에서는 재령이 증가함에 따라 수분함유량이 감소하게 되어 콘크리트의 종파 속도는 거의 증가하지 않는 반면에 강도는 점차적으로 증가하는 경향을 보이기 때문에 종파 속도와 콘크리트 강도의 상관관계 설정시 이를 반드시 고려해야 할 것으로 판단된다.

• 지구물리와물리탐사
• /
• 제14권4호
• /
• pp.305-315
• /
• 2011

암석시료에 대한 음파 속도측정의 정확성을 검증하고 정밀한 측정을 위한 기초적인 실험의 일환으로 아크릴과 스테인리스강 재질의 시료에 대하여 길이와 축하중을 달리하여 각각에 대해 3회씩 측정한 총 864 경우에 대하여, 시험편을 통과한 초동 주시를 측정하고 분석하였다. 축하중이 가해진 상태에서의 S-파 측정은 P-파에 비해 측정에 어려움이 있었으며 이에 따라 반복측정, 길이, 축하중에 의한 편차도 S-파가 훨씬 크게 나타났다. 또한, 재질에 따라서는 스테인레스강 시편보다는 아크릴 시편의 초동주시 편차가 약 2배 정도 양호하게 나타났으며 이는 아크릴 시험편의 경우가 트랜스 듀서와 시험편 간의 접촉 coupling이 안정적이며 또한 동일한 시간 분해능이나 유사한 전기적 잡음에 비하여 초동 주시가 길기 때문으로 판단된다. 실험결과, 아크릴 시험편과 스테인리스강 시험편의 탄성파 속도를 측정할 때는 60 ~ 90 mm 정도의 길이를 갖는 시험편을 20 kg (27.7 $N/cm^2$) ~ 30 kg (41.6 $N/cm^2$) 내외의 축하중 하에서 측정하는 것이 가장 좋으며, 스테인리스강 시험편의 S-파 속도는 길이 50 mm 이하의 시험편을 사용하여 측정해야 한다. 이러한 실험 결과는 암석 코어의 속도 측정시 시스템 지연의 측정 및 보정에 활용될 수 있을 것이다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1340-1352
• /
• 2008

In this study, S-wave velocity range is gauged in every field test method at the total 5 locations in the marine deposits in Incheon area. field test method is accomplished the SPT(Standard Penetration Test), CPT(Cone Penetration Test), SPS(Suspension PS Logger), SCPT (Seismic Cone Penetration Test) and so on. The S-wave velocity of SCPT in the downhole test method is measured lower than SPS logger at the N value > 15 range. But at the N value < 15 range, SPS logger and SCPT result is measured same. In this result, although the soil strength of the downhole test method increased, the rate of S-wave velocity is tend to be slowed. This result shows that the downhole test is difficult to apply at the place that the intensity of soil is more extreme and harder soil. And it shows that the existing Imai(1982) type that is mostly used within the country is not suitable for the marine deposits. Thus, the empirical formula that can show the range of S-wave velocity in each N value for domestic soil is needed.

• The Journal of the Acoustical Society of Korea
• /
• 제22권4E호
• /
• pp.167-175
• /
• 2003

Shear wave velocity was measured and grain size analysis was conducted on two core samples obtained in unconsolidated marine sediments of the western continental margin, the East Sea. A pulse transmission technique based on the Hamilton frame was used to measure shear wave velocity. Duomorph ceramic bender transducer-receiver elements were used to generate and detect shear waves in sediment samples. Time delay was calculated by changing the sample length from the transducer-receiver element. Time delay is 43.18 μs and shear wave velocity (22.49 m/s) is calculated from the slope of regression line. Shear wave velocities of station 1 and 2 range from 8.9 to 19.0 m/s and from 8.8 to 22 mis, respectively. Shear wave velocities with depth in both cores are qualitatively in agreement with the compared model〔1〕, although the absolute value is different. The sediment type of two core samples is mud (mean grain size, 8-9Φ). Shear wave velocity generally increases with sediment depth, which is suggesting normally consolidated sediments. The complicated variation of velocity anisotropy with depth at station 2 is probably responsible for sediment disturbance by possible gas effect.

• Journal of Magnetics
• /
• 제20권1호
• /
• pp.47-51
• /
• 2015

We measured radial arterial pulse signals using a prototype of a clip-type pulsimeter equipped with a permanent magnet and a Hall device, which produced signals through a voltage-detecting circuit. The systolic peak time and the reflective peak time for a temporally pulsed signal were analyzed for an arbitrary pulse wave at one position of a small permanent magnet. The measured value of the peripheral pulse wave velocity was about 1.25-1.52 m/s, demonstrating the accuracy of this new method. To measure the peripheral blood flow velocity, we simultaneously connected the radial artery pulsimeter to a photoplethysmography meter. The average value of the peripheral blood flow velocity was about 0.27-0.50 m/s.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2006년도 공동학술대회 논문집
• /
• pp.51-59
• /
• 2006

서해안 조간대에서 24 channel 탐사기로 획득한 표면파 자료의 위상속도와 군속도를 구한다음, 이를 역산하여 그 결과를 비교하였다. 위상속도의 분산곡선은 tau-p stacking 방법에 의하여, 군속도의 분산곡선은 wavelet analysis와 Multiple Filtering Technique의 두가지 방법을 사용하여 구하였다. 위상속도의 오차가 군속도의 오차보다 더 큰 것을 확인하였다. 군속도의 경우, wavelet analysis가 Multiple Filtering Technique 보다 fundamental mode와 higher mode를 구분하는데 더 효과적이었다. 역산결과, 군속도의 fundamental mode와 1st higher mode 를 동시에 사용했을 때, 공간적 해상도가 가장 좋았다. 이연구는 천부 지반의 S파 속도 구조를 구하는데, 군속도의 higher mode를 포함한 군속도 분산곡선을 사용하는 것이 효과적임을 시사한다.

• 대한기계학회논문집
• /
• 제17권8호
• /
• pp.1931-1939
• /
• 1993

The wave propagation characteristics of laminated composites subjected to a transverse high-velocity impact of a steel ball is investigated. For this purpose, high-velocity impact experiments were conducted to obtain the strain response histories, and a finite element analysis based on the higher-order shear deformation theory in conjunction with the static contact law is used. Test materials for investigation are glass/epoxy laminated composite materials with $[0^{\circ}/45^{\circ}/0^{\circ}/-45^{\circ}]_{2s}$ and $[90^{\circ}/-45^{\circ}/90^{\circ}-45^{\circ}/90^{\circ}]_{2s}$ stacking sequences. As a result, the strain responses obtained from the experiments represented the wave propagation characteristics in the transversely impact, also the wave propagation velocities obtained from high-velocity impact experiments and wave propagation theory agree well.