• 대한기계학회논문집A
• /
• 제40권11호
• /
• pp.935-941
• /
• 2016

고온기기의 부재로 널리 사용되는 인코넬 718을 사용하여 UNSM 표면처리법에 의한 처리효과를 기기의 사용조건을 고려한 실온, $300^{\circ}C$, $500^{\circ}C$ 및 $600^{\circ}C$ 의 세 가지 온도레벨하의 대기 중에서 고온피로 시험을 실시하여 각 시험편의 온도에 따른 피로특성을 연구하였다. 이때 고온회전굽힘피로시험(R=-1)은 할로겐(Halogen) 램프를 사용한 집광식인 가열방식을 선택한 새로운 피로시험기를 사용하였다. 인코넬 718의 고온피로강도는 상온에 비하여 감소하였다. 그러나 설계응력레벨에서는 상온의 내구한도와 유사한 경향을 나타내었다. UNSM 처리된 고온피로특성은 미처리재에 비하여 설계응력레벨에서 크게 향상되었다. 미처리재의 $300^{\circ}C$와 $500^{\circ}C$ 사이의 온도 영향은 거의 없었지만, $600^{\circ}C$에서는 높은 응력레벨에서 피로수명이 짧아졌지만, 낮은 설계응력레벨에서는 상온의 S-N선도보다 피로수명이 증가되는 경향을 나타내었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권1호
• /
• pp.42-46
• /
• 2017

The effects of the heat treatment temperature ($600^{\circ}C-1050^{\circ}C$) on the formation of $MgB_2$ and the superconducting properties have been examined. The self-synthesized $MgB_4$ and commercial Mg powders were used as raw materials for the formation of $MgB_2$. The superconducting critical temperatures ($T_cs$) of $MgB_2$ bulk superconductors prepared at $600^{\circ}C-850^{\circ}C$ were as high as 37-38 K regardless of the heat treatment temperature. However, because $MgB_4$ is more stable than $MgB_2$ at above $850^{\circ}C$, no superconducting signals were detected in the susceptibility-temperature curves of the samples prepared above $850^{\circ}C$. As for the critical current density ($J_c$), the sample heat-treated at a low temperature ($600^{\circ}C$) for a prolonged period (40 h) showed a Jc higher than those prepared at $650^{\circ}C-850^{\circ}C$ for a short period (1 h). The FWHM (full width at half maximum) result showed that the grain size of $MgB_2$ of the $600^{\circ}C$ sample was smaller than that of the other samples. The high $J_c$ of the $600^{\circ}C$sample is attributed to the presence of large numbers of grain boundaries, which can act as flux pinning centers of $MgB_2$.

• 대한의용생체공학회:의공학회지
• /
• 제16권2호
• /
• pp.209-216
• /
• 1995

Recently, a new tailored RF gradient echo (TRFGE) sequence was reported. This technique not only enhances the magnetic susceptibility effect but also allows us to measure local changes in brain oxygenation. In this study, a phantom and cat brain experiments were performed on a 4.7 Tesla BIQSPEC (BRUKER) instrument with a 26 cm gradient system. We have demonstrated that the signal intensity (SI) of the TRFGE sequence varies according to the concentration of susceptibility contrast agent. Three capillary tubes with different concentrations of Gd-DTPA (0.01, 0.05, 0.1 mMOI/l) were placed at the middle of a cylindrical water phantom. Using both TRFGE and conventional gradient echo (CGE) sequences, phantom images of the slices which contain all three tubes were obtained. For the animal experiment, cats were anesthetized and ventilated using halotane (0.5%) and a $N_2O/ O_2$ mixture (2:1), and blood pressure and heart rate were monitored and kept normal. For the observation of tue first pass of Gd- DTPA, imaging was started at t = 0. At t = 8 ~ 12s, 0.2 mMol/Kg Gd-DTPA was manually injected in the femoral vein. The imaging parameters were TRITE = 25/10 msec, flip angle = $30^{\circ}$, FOV = 10cm, image matrix size = $128{\times}128$ with 64 phase encodings and the image data acquisition window was 10 msec. SI-time curves were then obtained from a series of 30 images which were collected at 2 sec intervals using both CGE and TRFGE pulse sequences before, during, and following the contrast injection.

• Journal of Microbiology and Biotechnology
• /
• 제20권4호
• /
• pp.844-851
• /
• 2010

Controlling the dissolved oxygen (DO) in the fed-batch culture of the medicinal mushroom Ganoderma lucidum led to a 2-fold increase of the maximum biomass productivity compared with uncontrolled DO conditions. By contrast, extracellular polysaccharide (EPS) production was two times higher under oxygen limitation (uncontrolled DO) than under increased oxygen availability (controlled DO). Morphologically, dispersed mycelium was predominant under controlled DO conditions, with highly branched hyphae, consistent with the enhanced culture growth noted under these conditions, whereas in the uncontrolled DO process mycelial clumps were the most common morphology throughout the culture. However, in both cultures, clamp connections were found. This is an exciting new finding, which widens the applicability of this basidiomycete in submerged fermentation. In rheological terms, broths demonstrated shear-thinning behavior with a yield stress under both DO conditions. The flow curves were best described by the Herschel-Bulkley model: flow index down to 0.6 and consistency coefficient up to 0.2 and 0.6 Pa $s^n$ in uncontrolled and controlled cultures DO, respectively. The pseudoplastic behavior was entirely due to the fungal biomass, and not to the presence of EPS (rheological analysis of the filtered broth showed Newtonian behavior). It is clear from this study that dissolved oxygen tension is a critical process parameter that distinctly influences G. lucidum morphology and rheology, affecting the overall performance of the process. This study contributes to an improved understanding of the process physiology of submerged fermentation of G. lucidum.

• Bulletin of the Korean Chemical Society
• /
• 제35권6호
• /
• pp.1749-1753
• /
• 2014

Pseudo-first-order rate constants ($k_{obsd}$) have been measured spectrophotometrically for the nucleophilic substitution reaction of Y-substituted-phenyl picolinates (7a-f) with potassium ethoxide (EtOK) in anhydrous ethanol at $25.0{\pm}0.1^{\circ}C$. The plot of $k_{obsd}$ vs. [EtOK] curves upward while the plot of $k_{obsd}/[EtO^-]_{eq}$ vs. $[EtO^-]_{eq}$ is linear with a positive intercept in all cases. Dissection of $k_{obsd}$ into $k_{EtO^-}$ and $k_{EtOK}$ (i.e., the second-order rate constants for the reactions with the dissociated $EtO^-$ ion and ion-paired EtOK, respectively) has revealed that the ion-paired EtOK is more reactive than the dissociated $EtO^-$. The ${\sigma}^{\circ}$ constants result in a much better Hammett correlation than ${\sigma}^-$ constants, indicating that the reaction proceeds through a stepwise mechanism in which departure of the leaving group occurs after the rate-determining step (RDS). $K^+$ ion catalyzes the reaction by increasing the electrophilicity of the reaction center through formation of a cyclic transition state (TS). The catalytic effect decreases as the substituent Y becomes a stronger electron-withdrawing group (EWG). Development of a positive charge on the N atom of the picolinyl moiety through resonance interactions is responsible for the decreasing $K^+$ ion catalysis.

• 천문학논총
• /
• 제14권1호
• /
• pp.33-37
• /
• 1999

We have constructed a synthetic spectrum of the 2.5 micron $C_2H$ bands and compared them with diminutive structures in the near-infrared spectra of Comets P/Halley and West (1976 VI). We found that the Q branches of the $C_2H$ bands coincide with two small emission peaks in the spectra of the comets. We undertook Monte Carlo simulations using observed emission intensities of $C_2$ and possibly $C_2H$ in Comet P/Halley in order to derive a lifetime range of $C_2H$ and a production rate at the time of observations of P/Halley. We obtained a $C_2H$ production rate of $1\times10^{27}\;sec^{-1}$ for P/Halley on December 20, 1985, assuming the 2.5 micron features are due to $C_2H$. We derived a very short lifetime (<100 seconds) of $C_2H$ at 1AU heliocentric distance, assuming that the only parent molecule for $C_2H$ and $C_2$ is $C_2H$. Using this short lifetime we were unable to fit our $C_2$ distribution model to $C_2$ distribution curves observed by O'Dell et al.(1988), because our curve shows a steep slope compared with the observed one. We conclude that there must be significant additional source(s) for $C_2H$ and $C_2$ other than $C_2H_2$.

• 한국철도학회논문집
• /
• 제9권4호
• /
• pp.371-378
• /
• 2006

This study investigates the effects of the material properties and the fatigue behaviors in the SM490A material butt weld specimens due to the heat-treatment and the grinding. In the fatigue behavior, the heat-treatment affects the fatigue life. The S-N curves of both matrix specimen and butt weld specimen are reversed at some cycle by the existence or nonexistence of heat-treatment. The grinding on the bead makes the fatigue limit decrease in the all specimens. But the reinforcement removed, the fatigue limit increases at the high cycle. Also, this study investigates the fatigue life estimation by examining butt weld bead profiles. The butt weld beads, which are welded by semi-robot method, have non-uniform bead profiles described by $\theta,\;\rho$ and h. The stress concentration factors $K_t$, are changed by each different $\theta,\;\rho$ and h from 1.395 to 2.863. Hence, the sensitivity of $K_t$ is changed by each $\theta,\;\rho$ and h. As $\theta$ becomes lower and $\rho$ and h become higher, $K_t$ increases. The fatigue life can he estimated very closely for the AAY specimens without residual stress using only butt weld bead profiles. But, fur the AAN specimens with residual stress, the fatigue life must be estimated by considering both the weld bead profiles and the residual stress data.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2006년도 공동학술대회 논문집
• /
• pp.253-258
• /
• 2006

한반도는 고도의 산업화와 도시화로 인해 깨끗한 MT 및 GDS 자료를 획득하기 매우 어렵다. 이러한 환경에서는 적당한 신호 대 잡음비를 가지는 자료를 선별하는 전처리 과정이 필수적이다. 본 연구에서는 전자기장의 분광에너지에 기반한 자동 전처리 과정(RMP)을 한반도의 현실적인 상황을 고려하여 수정하였고, 이를 한반도 내륙에서 획득된 총 7 측점의 MT 자료에 적용하였다. 전반적으로, RMP 기법은 주기 10초 대역 부근에서 주파수에 따른 전기비저항과 위상의 연결성을 상당히 향상시켰다. 또한 RMP 기법에 의한 결과는 수작업으로 편집된 기존의 처리 결과와도 거의 유사였고, 특히 전기 비저항의 연결성면에서 그 우수성이 확인되었다.

• 대한화학회지
• /
• 제18권6호
• /
• pp.400-407
• /
• 1974

60몰%$AlCl_3$-40몰% NaCl의 용융염($453^{\circ}$<\TEX>K)속에든 알루미늄 전극에 대하여 전류-전압 편극곡선을 얻었다. 50mA/$CM^2$보다 큰 전류밀도에서는 옴-저항에 의한 전위차가 양극전위에 상당히 기여하므로 저항이 큰 $AlCl_3$(혹은 $AlCl_3$ 의 농도가 큰 멜트)의 층이 양극표면에 가까이 형성된다고 결론지었다. IR-전위차에 대하여 보정한 후의 Tafel곡선과 Allen-Hickling 곡선으로 부터 겉보기 transfer-coefficient, ${\alpha}_a$=(2.3RT/F)(dlogi/d${\eta}$)=$1.5{\pm}0.25$가 얻어졌다. 약 30mA/$cm^2$보다 큰 음극전류밀도에서는 느린 이온확산과 dendrite 생장 때문에 속도론적 측정이 방해 받았다.

• 소성∙가공
• /
• 제29권5호
• /
• pp.257-264
• /
• 2020

This paper is concerned with the influence of the plastic property of the rivet on the numerical prediction of the Self-Piercing Rivet (SPR) Joining. In order to predict the plastic property of the rivet, a ring compression specimen was directly fabricated from the rivet used for the mechanical joining of dissimilar materials, and the FE analysis together with the ring compression test was iteratively carried out by changing the plastic property of the rivet. For reliable FE analysis, a friction coefficient was estimated based on a friction calibration curve, measuring the reductions in inner diameter and height of the ring specimen after the compression test. From each simulation result, the force-displacement curves were then compared from each other so as to obtain the rivet plastic property that shows good agreement with the experimental result. The SPR joining between GA590 1.0t and Al5052 2.0t was conducted, and the numerical prediction was performed with the use of the plastic property evaluated based on the inverse analysis and the one referred from Mori et al. [11]. Comparison of the experiment and the numerical predictions in terms of the interlock and bottom thickness revealed that the reliable evaluation of the plastic property of the rivet is necessary for the trustworthy numerical prediction of the SPR joining.