• 터널과지하공간
• /
• 제28권5호
• /
• pp.476-492
• /
• 2018

본 연구에서는 한반도 남부 지역에서 취득 가능한 응회암, 현무암, 섬록암 시험편에 대하여 다양한 실내 시험을 수행하였다. 건조/포화 조건으로 대별하여 실내실험을 수행했으며 이를 바탕으로 포화에 따른 암석 물성변화를 실험적으로 고찰하였다. 실험결과, 비교적 공극률이 작은 시험편을 대상으로 했음에도 불구하고 확연한 강도 저하와 변형 특성 변화가 관찰되었다. 실험결과를 바탕으로 암석의 주요 역학적 물성인 일축압축강도, 탄성계수, 간접인장강도를 예측할 수 있는 회귀모델을 구성하였다. 비파괴 물성인 P파 속도, Shore 경도를 독립변수로 이용하였으며 그 결과 만족할 만한 수준의 물성 예측 모델이 구성되었음을 확인하였다.

• 대한기계학회논문집A
• /
• 제25권4호
• /
• pp.564-573
• /
• 2001

The mechanical properties of short carbon/glass fiber reinforced polypropylene are experimentally measured as functions of fiber content and nozzle diameter. Also, these properties are compared with the survival rate of reinforced fibers and fiber volume fraction using image analysis after pyrolytic decomposition. The survival rate of fiber aspect ratio as well as fiber volume fraction is influenced by injection processing condition, the used materials and mold conditions such as diameter of nozzle, etc. In this study, the survival rate of fiber aspect ratio is investigated by nozzle size variations in injection/mold sides. It is found that the survival rate of glass fiber is higher that the survival rate of glass fiber is higher than that of carbon fiber. Both tensile modulus and strength of short-fiber reinforced polypropylene are improved s the fiber volume fraction and nozzle diameter are increased.

• Elastomers and Composites
• /
• 제54권2호
• /
• pp.135-141
• /
• 2019

Polyphenylene sulfide (PPS) was filled with glass fiber (GF), aramid fiber (AF), and solid lubricants to improve the mechanical properties and wear resistance. The addition of GF effectively enhanced the tensile strength, flexural modulus, and impact strength of PPS, while solid lubricants such as polytetrafluoroethylene (PTFE), molybdenum disulfide ($MoS_2$), and tungsten disulfide ($WS_2$) lowered the friction coefficients of the composites to below 0.3. The ball nut and motor pulley of the electric power steering (EPS) were manufactured using the PPS composites, and feasibility was ascertained thereafter by conducting the durability test. The composites filled with GF and AF showed high mechanical strength, but slip occurred at the interface between the pulley and belt while testing above $50^{\circ}C$. When small amounts of lubricants were added, the slip was no longer detected because of the suppression of friction heat. It is realized that the low friction as well as high mechanical properties is important to ensure the reliability of plastic pulleys.

• Geomechanics and Engineering
• /
• 제21권6호
• /
• pp.571-582
• /
• 2020

Aiming at the mechanical and structural characteristics of the contact zone composite rock, the uniaxial compression tests and numerical studies were carried out. The interaction forms and formation mechanisms at the contact interfaces of different materials were analyzed to reveal the effect of interaction on the mechanical behavior of composite samples. The research demonstrated that there are three types of interactions between the two materials at the contact interface: constraint parallel to the interface, squeezing perpendicular to the interface, and shear stress on the interface. The interaction is mainly affected by the differences in Poisson's ratio and elastic modulus of the two materials, stronger interface adhesion, and larger interface inclination. The interaction weakens the strength and stiffness of the composite sample, and the magnitude of weakening is positively correlated with the degree of difference in the mechanical properties of the materials. The tensile-shear stress derived from the interaction results in the axial tensile fracture perpendicular to the interface and the interfacial shear facture. Tensile cracks in stronger material will propagation into the weaker material through the bonded interface. The larger inclination angle of the interface enhances the effect of composite tensile/shear failure on the overall sample.

• 소성∙가공
• /
• 제27권6호
• /
• pp.370-378
• /
• 2018

Cold forging, carried out at room temperature, leads to high dimensional accuracy and excellent surface integrity as compared to other forging methods such as warm and hot forgings. In the cold forging process, WC-Co (Tungsten Carbide-Cobalt) alloy is the mainly used material as a core dies because of its superior hardness and strength as compared to other structural materials. For cold forging, die life is the most significant factor because it is directly related to the manufacturing cost due to periodic die replacement in mass production. To investigate die life of WC-Co alloy for cold forging, mechanical properties such as strength and fatigue are essentially necessary. Generally, uniaxial tensile test and fatigue test are the most efficient and simplest testing method. However, uniaxial tension is not efficiently application to WC-Co alloy because of its sensitivity to alignment of the specimen due to its brittleness and difficulty in thread machining. In this study, shape of specimen, tools, and testing methods, which are appropriate for uniaxial tensile test for WC-Co alloy, are proposed. The test results such as Young's modulus, tensile strength and stress-strain curves are compared to those in previous literature to validate the proposed testing methods. Based on the validation of test results it was concluded that the newly developed testing method is applicable to other cemented carbides like Titanium carbides with high strength and brittleness, and also can be utilized to carry out fatigue tests for further investigation on die life of cold forging.

• Journal of the Korean Wood Science and Technology
• /
• 제27권2호
• /
• pp.15-22
• /
• 1999

진동 충격음 흡수성능을 지니는 샌드위치구조 목질 복합재료 제조용 폴리머는 넓은 온도범위(또는 주파수 범위)에서 높은 손실계수를 지니면서, 동시에 $5{\times}10^7\sim-10^9\;dyne/cm^2$의 탄성율을 지녀야 한다. 본실험에서는 이러한 점탄성 거동율 나타내는 고분자재료의 제조를 목적으로 에폭시 수지/아크릴 수지 상호침투망목고분자(IPNs)를 동시망목형성법으로 합성하였다. 고분자의 동적 점탄성은 Rheovibron을 사용하여 110Hz에서 측정하였으며, 복합체의 손실계수 및 동탄성 계수는 Rheovibron을 개조한 양단지지 강제 휨 진동법으로 주파수 110Hz에서 측정하였다. 동력학적 측정 결과, 손실탄성율의 최대값 온도 및 손실계수의 최대값 온도가 이동하고, 유리전이 영역이 확대되어, 이 IPNs계는 부분 상용계임을 알 수 있었다. 특히, 70/30 및 50/50 조성의 Epikote871/P(n-BMA) IPNs는 넓은 온도 범위에서 비교적 높은 손실계수 및 적당한 탄성율을 나타냈다. 또한 이를 적층한 목질 복합체는 넓은 온도 범위에서 비교적 높은 진동흡수 계수를 나타냈다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.85-88
• /
• 2005

The properties of pcc using BOF-slag were investigated in order to use as fine aggregate, which has been made in the steel making process and stabilized by air-jet method. The fluidity of flesh concrete has been improved with the usage of BOF-slag and it should be noted that the air content goes up. The compressive strength of hardened concrete was reduced at weight fraction over 50$\%$ and Young's modulus tends toward the trivial change. Also, the flexural and tensile strengths were increased with the usage, especially, the rupture values were increased to 1.2 times at the weight fraction of 30$\%$.

• 한국공간구조학회논문집
• /
• 제11권3호
• /
• pp.115-123
• /
• 2011

ETFE막재는 PTFE막재에 비해 상대적으로 두께가 매우 얇고 유연하기 때문에 다양한 온도환경에 따른 막재의 재료특성을 알아볼 필요가 있다. 본 논문에서는 ETFE 막재에 대해 다양한 온도하에서의 재료특성 실험을 수행하였다. 첫째로, -20$^{\circ}C$, 0$^{\circ}C$, +20$^{\circ}C$, +40$^{\circ}C$ 하에서 각각 5 시험편을 이용하여 인장실험을 수행하였으며, 각 온도하에서의 항복응력, 인장강도, 영계수를 도출하였다. 두 번째는, 25$^{\circ}C$, 40$^{\circ}C$, 60$^{\circ}C$ 하에서 각각 3MP, 6MP, 9MP의 하중을 가하여 각 온도에 따른 크리프 변형도를 알아보았다. 마지막으로, -15$^{\circ}C$, 0$^{\circ}C$, 20$^{\circ}C$ 하에서의 인열강도 시험을 수행하였다. 시험결과분석에 따르면, ETFE막재의 전제적인 거동은 크게 변하지 않았으나, 재료특생은 온도의 영향을 받고 있음을 알 수 있었다.

• 대한치과기공학회지
• /
• 제40권1호
• /
• pp.33-40
• /
• 2018

Purpose: The purpose of this study was to investigate the influence of mechanical properties of various ultra-dental stone by setting methods. Methods: 240 cylinder specimens($10mm{\times}20mm$) were prepared from three ultra-dental stones(Gemma, Die keen and Fuji rock; n = 80) in accordance with the manufacturers' recommendations. Half of the specimens of each stone(n = 40) were dried in open air within a room temperature; the other half(n = 40) underwent in a silicone rubber mold in open air for 30 minutes and then were dried in a microwave oven for 10 minutes to 600W. Compressive strength(CS), compressive modulus(CM) and diametral tensile strength(DTS) conducted until fracture using Instron 5966 at each of the following periods: 1 and 24 hours from mixing. One-way analysis of variance and Scheffe's post hoc test were performed for statistical comparisons at a significance level of P<.05. Results: The CS and CM values in all dental stone indicated highest after 24h(54.25 MPa < ) than the values for specimens dried in microwave method. The DTS values revealed the highest microwave method. However, in 24h, FJ(Fu-ji rock) and GM(Gemma) had lower mechanical properties than air. Conclusion : Within the limitations of this study, CS did not influence by microwave method but DTS affected according to the setting.

• 대한치과보철학회지
• /
• 제38권2호
• /
• pp.226-241
• /
• 2000

Recently a new generation of crown and bridge veneering resins containing submicron glass fillers was introduced. These ultrasmall particle hybrid composite materials distinguish themselves, compared with conventional microfill crown and bridge resins, through improved mechanical properties. It is claimed that these composites are suitable for metal free crowns and even bridges using fiber reinforcement. The purpose of this study was to evaluate the effect of thermal cycling on the tensile strength of the following veneering composites: Artglass(Heraeus Kulzer Co., Wehrheim, Germany), Estonia(Kuraray Co.. Japan), Sculpture(Jeneric Pentron Co., Wallingford, U.S.A.), and Targis(Ivoclar Co., Schaan Liechenstein). According to manufacturer's instructions, rectangular tensile test specimens measuring $1.5{\times}2.0{\times}4.5mm$ were made using a teflon mold. Whole specimens were divided into two groups. One group was dried in a desiccator at $25^{\circ}C$ for 10 days, and another group was subjected to thermal cycling($10,000{\times}$) in water($5/55^{\circ}C$). All test specimens were placed in a universal testing machine and loaded until fracture with a crosshead speed of 0.5mm/min. Weibull analysis and Tukey's test were used to analyze the data. The fracture surfaces of specimens were observed in SEM and the aliphatic C=C absorbance peak of Estenia and Targis resin was analyzed using Fourier transform infrared(FTIR) spectroscopy. Within the limitations imposed in this study, the following conclusions can be drawn: 1. Both in drying condition and thermal cycling condition, the highest tensile strength was observed in Estenia testing group(p<0.05). 2. The strength data were at to single-mode Weibull distribution, and the Weibull modulus of all veneering composite resin specimens increased after thermal cycling treatment. 3. After thermal cycling test, the highest tensile strength was observed in the Estenia group, and the lowest value was observed in the Targis group. The tensile strength values showed the significant differences between each group(p<0.05) 4. The aliphatic C=C absorbance peak of Estonia and Targis resin was decreased after light curing, and there was no distinct change after thermal cycling.