• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.6
• /
• pp.635-642
• /
• 2014

In this paper, an efficient technique is developed to predict failure probability of three failure modes(case rupture, fracture and bolt breakage) related to solid rocket motor case due to the inner pressure during the mission flight. The overall procedure consists of the steps: 1) design parameters affecting the case failure are identified and their uncertainties are modelled by probability distribution, 2) combustion analysis in the interior of the case is carried out to obtain maximum expected operating pressure(MEOP), 3) stress and other structural performances are evaluated by finite element analysis(FEA), and 4) failure probabilities are calculated for the above mentioned failure modes. Axi-symmetric assumption for FEA is employed for simplification while contact between bolted joint is accounted for. Efficient procedure is developed to evaluate failure probability which consists of finding first an Most Probable Failure Point(MPP) using First-Order Reliability Method(FORM), next making a response surface model around the MPP using Latin Hypercube Sampling(LHS), and finally calculating failure probability by employing Importance Sampling.

• Korean Journal of Agricultural Science
• /
• v.13 no.1
• /
• pp.113-122
• /
• 1986

In order to promote mechanization of corn harvesting in Korea, this study was conducted to find out the effect of moisture content on compressive properties such as force, deformation, energy and modulus of stiffness to the bioyield and the rupture point for Korean corn kernel. In this study, the loading positions of corn were flat, edge, longitude and the moisture contents were about 13, 17, 21, 25% in wet basis. The compression test was carreied out with flat plate by use of dynamic straingage for three varieties of Korean corn under quasi-static force when the loading rate was 1.125mm/min. The results of this study are summarized as follows; 1. When the moisture content of corn ranged from 12.5 to 24.5 percent, at flat position, the bioyied force was in the range of 13.63-26.73 kg and the maximum compressive strength was in the range of 21.55-47.65kg. Their values were reached minimum at about 17% and maximum at about 21% moisture content. The bioyield force was in the range of 13.58-6.70kg at edge position and the maximum compressive strength which was 16.42 to 7.82kg at edge position was lower than that which was 18.55-9.05kg at longitudinal position. 2. Deformation of corn varied from 0.43 to 1.37 mm at bioyield point and from 0.70 to 2.66mm at rupture point between 12.5 to 24.5% moisture content. As the moisture content increased, deformation was increased. 3. The moduli of resilience and toughness of corn ranged from 2.60 to 8.57kg. mm and from 6.41 to 34.36kg. mm when the moisture content ranged from 12.5 to 24.5 percent, respectively. As the moisture content increased, the modulus of toughness was increased at edge position and decreased at longitudinal position. And their values were equal each other at 22-23% moisture content. 4. The modulus of stiffness was decreased with increase in the moisture content. Its values ranged from 32.07 to 5.86 kg/mm at edge position and from 42.12 to 18.68kg/mm at flat position, respectively. Also, the values of Suweon 19 were higher than those of Buyeo. 5. It was considered that the compressive properties of corn at flat position were more important on the design data for corn harvesting and processing machinery than those of edge or longitudinal position. Also, grinding energy would be minimized when a corn was processed between about 12.5 to 17% moisture content and corn damage would be reduced when a corn was handled between about 19 to 24% moisture content in wet basis.

• Journal of Korean Neurosurgical Society
• /
• v.29 no.12
• /
• pp.1555-1562
• /
• 2000

Objects : Surgical management of the distal anterior cerebral artery(DACA) aneurysms presents several unique problems to surgeons, such as difficulty in early identification of parent arteries, high incidence of rebleeding and premature rupture, and requirement of unfamiliar approach other than conventional frontotemporal craniotomy. Therefore, preoperative anatomical knowledge of anterior interhemispheric fissure and entry point of dissection is prerequisite. Authors utilized a frontobasal approach for DACA aneurysms by using consistent external landmark for guidance to the deep structure. Materials and Methods : From Nov. 1995 to Jun. 1999, a surgical clipping of DACA aneurysms was carried out in 9 patients among a total 131 patients with intracranial aneurysms. In each case, the clinical and aneurysmal features were carefully reviewed through the angiograms, medical records, and intraoperative findings. Results : The incidence of DACA aneurysms was 6.9% from our series. All cases were arisen from juxtacallosal por-tion ; 6 cases from pericallosal-callosomarginal(PC-CM) junction and 3 from pericallosal-frontopolar(PC-FP) junction. Associated vascular anomalies were noted in 3 cases and multiple aneurysms in 3 cases, respectively. The preoperative clinical grades were generally poor. An early surgery was performed in 7 cases and frontobasal interhemispheric approaches in 7 cases. Postoperatively, two patients died of complications ; one delayed ischemic vasospasm and one aspiration pneumonia but remaining patients recovered well. Conclusion : The frontobasal interhemispheric approach was useful for DACA aneurysms in early surgery. Division of superior sagittal sinus(SSS) enabled a minimal retraction of brain on both sides, and prevention of intraoperative rupture was possible. Authors suggest the frontopolar(first frontal bridging) vein as a constant external landmark for approaching the genu of the corpus callosum and juxtacallosal DACA aneurysms.

• Korean Journal of Materials Research
• /
• v.1 no.3
• /
• pp.156-167
• /
• 1991

The purpose of this study is to develop a data base for material selection of turbofan engines, which is preferred in these days on many application due to their high performance with economical operation. Hundreds of Super Alloys have been developed by this time, each having special properties. Since it is very difficult task for a design engineer to select materials of adequate Properties for specific engine components, a good data bate is strongly desired to manage informations on various kinds of materials. However, no basic research is reported in this area so far in our country. The operating conditions such as temperature, pressure, rpm of spools are assumed to be provided by other mechanical studies. Creep rupture strength, corrosion resistance, yield strength, thermal expansion, melting point, etc., are considered as typical properties in this study to search a group of candidate materials. Formability, manufacturing or purchase cost can also be important variables to be considered. As a result of this study, a user-friendly computer program has been developed for input of new material information, interactive material selection, and output of selection results. Finally, discussion is presented from. the viewpoint of materials engineering. A method to evaluate the performance of the selected materials is also suggested.

• Journal of the Korean Institute of Gas
• /
• v.22 no.5
• /
• pp.62-71
• /
• 2018

According to own investigation conducted by Korea Gas Safety Corporation Gas Safety Research Institute in 2017, the length of underground pipes in domestic high-pressure gas pipelines is approximately 770km, of which 84% is buried in Ulsan and Yeosu industrial complexes. In particular, 56% of underground pipelines have been in operation for more than 20 years. This suggests urgent management of buried high pressure gas pipelines. PHMSA in US and EGIG in Europe, major causes of accidents in buried gas pipelines are reported as third party damage, external corrosion and loss of pipe wall thickness. Therefore, it is important to evaluate whether the defects affect the remaining life of the pipe when defects occur in the pipe. DNV and ASME have evaluated the residual strength of pipelines through the hydraulic rupture test using pipe specimens with artifact flaws. Once the operating pressure is known through the residual strength of the pipe, the wall thickness at the point at which the pipe ruptures is calculated. If we know the accurate rate of corrosion growth, we can predict the remaining life of pipe. In the study, we carried out experiments with A53 Grade.B and A106 Grade.B, which account for 80% of domestic buried pipes. In order to modify the existing model equation, specimens with a defect depth of 80% to 90% was tested, and a formula expressing the relationship between defect and residual strength was made.

• Archives of Reconstructive Microsurgery
• /
• v.9 no.2
• /
• pp.114-119
• /
• 2000

The soft tissue defects including the Achilles tendon are complex and very difficult to reconstruct. Recently, several free composite flaps including the tendon have been used to reconstruct large defects in this area in an one-stage effort. Our case presents a patient reconstructed with free composite dorsalis pedis flap along with the extensor digitorum longus and superficial peroneal nerve for extensive defects of the Achilles tendon and surrounding soft tissue. A 36-year-old-man sustained an open injury to the Achilles tendon. He was referred to our department with gross infection of the wound and complete rupture of the tendon associated with loss of skin following reduction of distal tibial bone fracture. After extensive debridement, $6{\times}8cm$ of skin loss and 8cm of tendon defect was noted. Corresponding to the size of the defect, the composite dorsalis pedis flap was raised as a neurosensory unit including the extensor digitorum longus to provide tendon repair and sensate skin for an one-stage reconstruction. One tendon slip was sutured to the soleus musculotendinous portion, the other two were sutured to the gastrocnemius musculotendinous portion with 2-0 Prolene. The superficial peroneal nerve was then coaptated to the medial sural cutaneous nerve. The anterior tibial artery and vein were anastomosed to the posterior tibial artery and accompanying vein in an end to end fashion. After 12 months of follow-up, 5 degrees of dorsiflexion due to the checkrein deformity and 58 degrees of plantar flexion was achieved. The patient was able to walk without crutches. Twopoint discrimination and moving two-point discrimination were more than 1mm at the transferred flap site. The donor site healed uneventfully. Of the various free composite flaps for the Achilles tendon reconstruction when skin coverage is also needed, we recommand the composite dorsalis pedis flap. The advantages such as to control infection, adequate restoration of ankle contour for normal foot wear, transfer of the long tendinous portion, and protective sensation makes this flap our first choice for reconstruction of soft tissue defect including the Achilles tendon.

• Research in Community and Public Health Nursing
• /
• v.13 no.2
• /
• pp.280-291
• /
• 2002

Objectives: This study was conducted to evaluate the maternal child health services provided by public health centers in Pyungtaek city. Methods: Data were collected based on multiple sources of official records. A questionnaire survey was obtained from 50 mothers with premature babies, and 89 mothers with full- term babies, in order to compare their demographic factors, and physical, obstetrical, and emotional status. In addition, the investigators collected data on pre and post follow-up care for the remature group to evaluate the effects of home visiting services on them. Moreover, additional data were collected from 135 pregnant women and 315 mothers with infants, to assess their degree of satisfaction for prenatal education course and breast feeding practices. Results: 1) The pregnant women's satisfaction for the prenatal education course, knowledge, and practices on self care were considered to be high. 2) Of the mothers with infants, 62.9% experienced breast feeding, but only 35.9% of them did it for six months. 3) Premature birth rate in the region was 5.6%, and 75.6% of all premature babies received follow-up care. 4) The mothers with premature babies experienced premature rupture of membrane. placenta previa, preeclampsia, and cesarean section more frequently than the mothers with full-term babies. 5) At the pre-intervention data collection point. mothers with premature babies experienced significantly less social support than mothers with full-term babies. In addition, mothers with premature babies reported higher levels of stress and care-giving burdens, and lower level of self esteem, than mothers with full-term babies, although the differences were not statistically significant. 6) In the premature group, stress, care giving burdens, and postpartum depression decreased after the intervention, whereas maternal self esteem, and the husband's support were increased after the intervention. Social support from significant others were somewhat decreased. 7) Satisfaction for the home visiting service in the mothers with premature babies was very high. Conclusion: These results showed a possibility that the recently started maternal child health services provided by the public health centers may be efficient. Although statistically significant differences were not found, the investigators found a potential for changes in a positive direction. Long-term effects of the health services on maternal child health needs should be addressed in future studies.

• Journal of Korean Neurosurgical Society
• /
• v.63 no.5
• /
• pp.590-597
• /
• 2020

Objective : Covered stenting is an optional strategy for traumatic carotid pseudoaneurysm, especially in malignant conditions of potential rupture, but the long-term outcomes are not clear. Our aim was to determine if covered stenting is an effective option for traumatic carotid pseudoaneurysm with promising long-term outcomes. Methods : Self-expanding Viabahn and balloon-expandable Willis covered stents were separately implanted for extra- and intracranial traumatic carotid pseudoaneurysm. The covered stent was placed across the distal and proximal pseudoaneurysm leakage under roadmap guidance. Procedural success was defined as technical success (complete exclusion of the pseudoaneurysm and patency of the parent artery) without a primary end point (any stroke or death within 30 days after the procedure). Long-term outcomes were evaluated as ischemic stroke in the territory of the qualifying artery by clinical follow-up through outpatient or telephone consultation and as the exclusion of the pseudoaneurysm and patency of the parent artery by imaging follow-up through angiography. Results : Five patients with traumatic carotid pseudoaneurysm who underwent covered stenting were enrolled. The procedural success rate was 100%. No ischemic stroke in the territory of the qualifying artery was recorded in any of the five patients during a mean clinical follow-up of 44±16 months. Complete exclusion of the pseudoaneurysm and patency of the parent artery were maintained in all five patients during a mean imaging follow-up of 39±16 months. Conclusion : Satisfactory procedural and long-term outcomes were obtained, suggesting that covered stenting is an effective option for traumatic carotid pseudoaneurysm.

• Journal of Trauma and Injury
• /
• v.22 no.1
• /
• pp.77-86
• /
• 2009

Purpose: The appropriate management of traumatic truncal arterial injury is often difficult to determine, particularly if the injury is associated with severe additional truncal lesions. The timing of repair is controversial when patients arrive alive at the hospital. Also, there is an argument about surgery versus stent-graft repair. This study's objective was to evaluate the appropriate method and the timing for treatment in cases of truncal abdominal injury associated with other abdominal lesions. Methods: The medical records at Ajou University Medical Center were reviewed for an 8-year period from January 1, 2001, to December 31, 2008. Twelve consecutive patients, who were diagnosed as having had a traumatic truncal arterial injury, were enrolled in our study. Patients who were dead before arriving at the hospital or were not associated with abdominal organ injury, were excluded. All patients involved were managed by using the ATLS (Advanced Trauma Life Support) guideline. Data on injury site, the timing and treatment method of repair, the overall complications, and the survival rate were collected and analyzed. Results: Every case showed a severe injury of more than 15 point on the ISS (injury severity score) scale. The male-to-female ratio was 9:3, and patients were 41 years old on the average. Sites of associated organ injury were the lung, spleen, bowel, liver, pelvic bone, kidney, heart, vertebra, pancreas, and diaphragm ordered from high frequency to lower frequency. There were 11 cases of surgery, and one case of conservative treatment. Two of the patients died after surgery for truncal organ injury: one from excessive bleeding after surgery and the other from multiple organ failure. Arterial injuries were diagnosed by using computed tomography in every case and 9 patients were treated by using an angiographic stent-graft repair. There were 3 patients whose vessels were normal on admission. Several weeks later, they were diagnosed as having a truncal arterial injury. Conclusion: In stable rupture of the truncal artery, initial conservative management is safe and allows management of the major associated lesions. Stent grafting of the truncal artery is a valuable therapeutic alternative to surgical repair, especially in patients considered to be a high risk for a conventional thoracotomy.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.1
• /
• pp.148-156
• /
• 2020

The paper is a summary of the results of the basic pullout test which is conducted to evaluate the anchorage capacity of high strength headed bars that is mechanical anchored vertically on steel fiber reinforced concrete members. The main experimental parameters are volume fraction of steel fiber, concrete strength, anchorage length, yield strength of headed bars, and shear reinforcement bar. Both sides of covering depth of the specimen are planned to double the diameter of the headed bars. The hinged point is placed at the position of each 1.5𝑙_dt and 0.7𝑙_dt around the headed bars, and the headed bars are drawn directly. As a result of pullout test experiment, concrete fracture and steel tensile rupture appear by experimental parameters. The compressive strength of concrete is 2.7~5.4% higher than that of steel fiber with the same parameters, while the pullout strength is 20.9~63.1% higher than that of steel fiber without the same parameters, which is evaluated to contribute greatly to the improvement of the anchorage capacity. The reinforcements of shear reinforcements parallel to the headed bars increased 1.7~7.7% pullout strength for steel fiber reinforced concrete, but the effect on the improvement of the anchorage capacity was not significant considering the increase in concrete strength. As with the details of this experiment, it is believed that the design formula for the anchorage length of KCI2017and KCI2012 are suitable for the mechanical development design of SD600 head bar that is perpendicular to the steel fiber reinforced concrete members.