• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.69-75
• /
• 2015

Stone board for the rock bed was needed to reduce weight using thin thickness and reinforced materials. In this work, stone/wood board for rock bed was studied. Stone and wood were attached to reduce total weight of stone for rock bed. For reinforcing wood heat treatment method was used to change surface and mechanical properties. Mechanical strength of heat treated wood increased more than neat condition. The optimum heat treatment condition was set on $100^{\circ}C$ under tensile, flexural loads whereas surface energy was also obtained by contact angle measurement. Optimum adhesive condition was to get the maximum adhesion between stone and wood. Lap shear test was performed for stone/wood board with different adhesives such as amine type epoxy, polyurethane, chloro-rubber and vinyl chloride acetate type. Fracture surface of lap shear test was shown at wood fracture part on stone using amine type epoxy adhesive. It was found that for high adhesion between stone and wood the optimum adhesive was epoxy type for the rock bed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.9
• /
• pp.620-626
• /
• 2011

The purpose of this study is to evaluate a simulation model of a stacking guidance system (SGS) with a roller guide applicable to the mobile harbor. The study used a small-scale model (1/20) made of wood with rollers in order to compare the dynamic analysis with experiment results. The law of similarity was applied for the validation of the scaled model. In order to construct a more realistic simulation model, the damping coefficient of the dynamic model was adjusted to 0.5 Ns/mm for the wood-to-wood contact condition based on the experimental results. Using this validated model, dynamic simulations were also carried out for containers of 20, 30, and 40 tons. The results showed that the reaction force of the roller guide was increased from 74.7 kN to 91.2 kN as the weight of container increased. For the design of a roller guide for SGS, the results obtained in this study can be used to reduce the reaction force by employing a rubber roller or a highly damped rotational joint.

• Journal of Environmental Health Sciences
• /
• v.20 no.3
• /
• pp.13-18
• /
• 1994

Information on the heating values of municipal solid wastes is very important in evaluating the feasibility of incineration and RDF (Refuse Derived Fuel) manufacture. This paper describes the forecasting methods about the lower heating values of municipal solid wastes. The lower heating values are forecast by the heating values of physical components. The municipal solid wastes consist of paper, food wastes, textiles, plastics, wood and rubber (contained leather). These are the physical components of municipal solid wastes.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.211-217
• /
• 2011

Wood Polymer Composite (WPC) has attracted a great deal of attention in environmental industries due to renewable resources, processability, excellent physical properties and logging regulations for application to housing units and engineering construction materials. In this study, commercial WPCs were prepared by using a modular intermeshing co-rotating twin screw extruder. The effect of three main factors such as wood flour contents, coupling agent concentrations and pre-treatment of wood flour on the properties of WPCs was extensively investigated. It was found that tensile strength and thermal stability were decreased with increasing wood flour contents whereas the water absorption was increased. Addition of maleic anhydride grafted polypropylene (PP-g-MA) into WPC exhibited better physical properties. On the contrary, the water absorption was slightly decreased with PP-g-MA. Finally the sample, which was prepared with pre-treated wood flour, represented the highest tensile strength. However, the water absorption of the sample was increased due to the transition of crystalline structure of cellulose.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.218-222
• /
• 2011

The effect of cycled temperature change on the mechanical properties of wood flour(50 wt.% and 70 wt.%) polypropylene WPC(Wood Plastic Composites) was investigated in this study. Flexural modulus and flexural strength of the WPC showed a decrease due to the degradation of interfacial adhesion between polymer matrix and wood flour by the freeze-thaw test regardless of the cycled number. At the higher loading level of wood flour, the reduction of the flexural modulus was remarkable. After the cycled heat-freeze test, it was found that the flexural modulus and flexural strength of the WPC were lower at the high temperature ($60^{\circ}C$) and higher at the low temperature ($-20^{\circ}C$). At the low temperature ($-20^{\circ}C$) which is below glass transition temperature of polypropylene ($-10^{\circ}C$), WPC is in a glassy state which brings about the high stiffness and strength. At the high temperature ($60^{\circ}C$), the flexural modulus and flexural strength of the WPC with 50 wt.% wood flour were lower because of the increase of polymer ductility.

• Journal of Biosystems Engineering
• /
• v.27 no.1
• /
• pp.67-76
• /
• 2002

This study was conducted to investigate the effects of impact conditions on the acoustic characteristics of a watermelon. The study was crucial to develop a device for nondestructive internal quality evaluation of a watermelon by an acoustic impulse response method. An impact device was constructed with a pendulum to hit the watermelon, a microphone to detect the acoustic impulse responses, and a digital oscilloscope and computer to store and analyze the data. The selected samples were Guemcheon cultivar watermelons(Citrulus Vulgaris Schrad) harvested on Oct. 20,1998. Sixty watermelons were tested on flour different types of sample holders, with four kinds of ball made of different materials, at four bevels of the angular position of the pendulum and distance from the watermelon to the microphone. Since the magnitudes of frequencies obtained by hitting with the steel and rubber ball were relatively small at the bandwidths of above 500 Hz, it was shown that the steel and rubber ball were not suitable far a hitting ball in the pendulum to get informations on internal quality of the watermelon. In case of using broth of the wood and acryl ball, almost the same and good acoustic responses were shown on the wide range of frequency bandwidth. Therefore, it seemed that the acryl ball was more suitable to the test than the wood ball in considering its mechanical properties. The acoustic characteristics of the watermelon were not shown a significant difference between the types of sample holder. The amplitudes of the acoustic signals and the magnitudes of frequencies from the whole samples increased with increase of the angular position of pendulum and with decrease of the distance from the watermelon to the microphone. However, the resonance resonance of the sample were almost the same regardless of the angular positions and the distances.

• Journal of the Korea Furniture Society
• /
• v.19 no.4
• /
• pp.273-282
• /
• 2008

Increasing demand for timber and the depletion of natural forest have encouraged utilization of many non-popular species. The understanding of wood properties and behavior is important to evaluate the potential of these species to produce high quality end products. This study determines the anatomical and physical properties of Hevea species viz Hevea pauciflora, Hevea guianensis, Hevea spruceana, Hevea benthamiana and Hevea brasiliensis. Each sample tree was cut into three different portions along the height (bottom- B, middle- M and upper -T parts) and two radial samples (outer- O and inner- I parts). H. brasiliensis clone RRIM 912 exhibited the longest fibre with $1214{\mu}m$, followed by H. benthamiana (HB, $1200{\mu}m$), H. pauciflora (HP, $1189{\mu}m$), H. spruceana (HS, $1158{\mu}m$) and H. guianensis (HG, $1145{\mu}m$). Fibre length has a positive correlation with specific gravity. The largest fibre diameter ($24.9{\mu}m$) and lumen diameter ($12.5{\mu}m$) were recorded in H. guianensis. The highest moisture content was obtained from H. spruceana (64.34%) compared to the lowest with 60.01% (Clone RRIM912). The higher moisture content is normally associated with lower strength. Overall, the properties of clone RRIM 912 is found to be comparatively better because of higher strength due to longer fibre length, thicker cell walls and higher specific gravity than the other Hevea species. Therefore, this species can be used as a general utility timber.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.4
• /
• pp.1-7
• /
• 2004

The change in surface temperature of woodceramics, made from thinned logs of Pinus densiflora, were investigated, by the impregnation ratio and carbonizing temperature. As the surface temperature of silicon rubber heater was going up, that of woodceramics also increase rapidly. In case of heaters surface temperature at 70℃, the surface temperature of woodceramics was 53.9℃ when a sample was the impregnation ratio of 80%, while it was 54.2℃ when a sample was at 1,000℃ in carbonizing temperature, showing the highest. Also, it was found that woodceramics maintained heat for a long time because the descending velocity of their surface temperature was lower than that of the heater.

• Journal of the Korean housing association
• /
• v.25 no.2
• /
• pp.19-26
• /
• 2014

The number of elderly who wants to access to Nursing Homes (NH) will increase due to the rapid aging society and domestic changes. Those who move into NH expect 24/7 care service in safe environment. Providing space free from danger, especially from fall, for the frail elderly is essential. The purpose of this study is to categorize performance needs of flooring materials in the aspect of safety, and analyze materials so that adequate ones for each space in NH can be suggested. Performance needs are as follows; slip resistance (dry/wet), fire resistance, resilience, water resistance, soil retardant, anti-bacterial, gloss, sound absorbtion. maintenance, durability, ease replacement, color and pattern variety, visual and tactual texture, tactile warmth, IAQ, sustainable material (before use), impact to nature (after use). They are categorized under function, economy, sensibility and sustainability. It was found that there are better materials than common ones that has been used repeatedly in NHs, such as vinyl sheets and VCT. In overall, Cork flooring and nylon carpet met all four categories, followed by wool carpet, rubber and linoleum. For bedroom, wood flooring, Cork, rubber, wool carpet, nylon carpets were suggested. In bathroom with shower, rubber, vinyl sheet and porcelain tiles were safe materials. As living/dining room and corridor floors, wool carpet, nylon carpet, cork flooring would be excellent as they are resilient and durable. The result of this paper can be used by both NH managers and material companies, resulting better quality of life of the elderly by providing safe environment.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.61-70
• /
• 1996

침엽수재(針葉樹材)(Radiata pine, Pinus radiata)MDF와 활엽수재(闊葉樹材)(Rubber wood, Hevea brasiliensis)MDF 각 1종을 대상으로 MDF를 제조하기 전 원료(原料) 섬유(纖維)의 미세(微細) 구조(構造) 및 내부결합력 시험 후 MDF의 파괴면(破壞面)에서 섬유표면(纖維表面)에 접착제(接着劑)가 도포(塗布)된 형태를 주사전자현미경(走査電子顯微鏡)으로 관찰하였다. 원료 섬유는 침(針) 활엽수재(闊葉樹材) 모두 fiber twisting 및 shrinkage fold 등이 관찰되었다. 침엽수재(針葉樹材)의 경우는 유연벽공부(有緣壁孔部)에서 유연벽공(有緣壁孔)이 없는 부분에 비하여 shrinkage fold의 발생 빈도가 낮고 표면(表面) 박리(剝離)는 가도관(假導管) 중 벽공이 없는 부분에서 관찰되었다. 활엽수재(闊葉樹材) 목섬유(木纖維)는 침엽수재(針葉樹材)와 마찬가지로 shrinkage fold가 관찰되었으나 표면(表面) 박리(剝離)는 거의 관찰되지 않았다. 활엽수(闊葉樹) 섬유(纖維)에서는 벽공의 유무에 따른 shrinkage fold의 차이(差異)가 거의 관찰되지 않았는데 이는 목섬유(木纖維)가 침엽수(針葉樹) 가도관(假導管)보다 작은 단벽공(單壁孔)을 갖기 때문으로 생각된다. 또 방사유세포(放射柔細胞)와 가도관(假導管) 및 목섬유(木纖維)의 박리(剝離) 부분(部分)에는 융기부(隆起部)가 관찰되었다. 내부결합력 시험후 나타난 파괴면을 통하여 접착제 분포를 관찰한 결과 거의 모든 섬유(纖維)들이 접착제(接着劑)로 둘러싸여 있었으며 섬유(纖維)간 접착형태(接着形態)도 매우 다양하였다. 침활엽수재(針闊葉樹材)간에 강도(强度)의 차이는 있었지만 파괴(破壞) 형태(形態)는 큰 차이를 나타내지 않았다. 즉 침활엽수(針闊葉樹) 모두 접착층(接着層)이 아닌 섬유(纖維)에서 파괴(破壞)가 발생하였으며 섬유에서 박리(剝離)된, 세포벽(細胞壁)의 일부가 다른 섬유(纖維)의 표면(表面)에 남아있는 형태와 섬유(纖維) 표면(表面)에서 떨어져 나간 형태로 관찰되었다. 세포 구성이 단순한 침엽수(針葉樹) MDF에 비하여 유세포(柔細胞)와 도관(導管) 및 목섬유(木纖維)의 파편들이 활엽수(闊葉樹) MDF에서는 다양(多樣)하게 분포하였다.