• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.22 no.2
• /
• pp.33-37
• /
• 2016

One-way degassing valves usually designed for coffee packaging are recently applied to the various food packaging such as fermented health functional food or home meal replacement (HMR) packaging. The optimized degassing pressure by food product is important factor for keeping effective freshness and improving preservation of the food, therefore the development of degassing valves specified with various open pressure is needed. In this study, the mechanical characteristics of the degassing valve with ring type rubber disk were analyzed and a mathematical model was developed to predict the open pressure of the valve. The model was verified with test results derived from several available valves, and it may be useful in designing and developing a new valve.

• Resources Recycling
• /
• v.11 no.4
• /
• pp.11-16
• /
• 2002

Analysis and separation of constituent materials of old car have been performed by using the industrial shredding line. For this aim, three old cars made by domestic automobile manufacturers, Sonata II, Sephia and Prince were chosen and delivered in pressed form without engine, tires and doors, etc. Shredding line was substantially composed of pre- and main-shredder. cyclone, magnetic separation, eddy current separation and man-power separation. From the separation of shredder products, iron scrap was observed to be the major material of old car accounting for 60.1 ％ of total weight and non-ferrous metals involving Al, Cu and Zn, etc. were about 2％. Light fluff, about 90％ of total fluff product, was comprised with plastic, fiber and sponge, etc. and the fraction of 5 cm undersize in light fluff was 70.5%. In case of heavy fluff, however. rubber and plastic were found to be the major constituent materials of it. Among the constituent materials of fluff, plastic showed the highest calorific value, more than 10,000 cal/gr and leather and rubber showed relatively high chlorine content, 10.3 and 2.55 wt%, respectively.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.20 no.2
• /
• pp.35-39
• /
• 2014

One-way degassing valves are designed to allow pressure to be released from an air-tight package while preventing air from getting back into the package. Air, especially the oxygen ($O_2$) portion of air, can have negative effects on the package contents and its freshness. The most common application of the one-way degassing valve is for fresh roasted coffee. Demands of one-way degassing valves have been increasing with the high growth of global coffee market. In this study, we have developed one-way degassing valves for coffee and food packaging using ring type rubber disk, named SP valve. Its quality and performance was verified with test results to be equal with that of global top maker's product, Goglio valve. SP valves showed 820~1200 Pa of opening pressure, 10~50 Pa of closing pressure, 1.2~1.6 L/ min of flow rate. And, the SP valve applicable to ferment food packaging is expected to contribute to globalize Korean traditional food.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.08a
• /
• pp.29-34
• /
• 2003

In order to study the shearing characteristics of anti-vibration sheet metal which has been bonded by resin, a blanking die of 40.02mm was manufactured to blank a material and it is used to reduce vibrational noise. The variables employed in this study were 1) Clearance 2) types of stripper plate, and 3) types of the die design technique. These variables were used to study the effects on burr height, diameter of product, and camber height. Lastly, the effect of the position of the rubber during blanking was observed. In the case of burr height from experimental investigation, the push-back die, combined with a movable stripper plate, resulted in the concentration of additional pressure between the cutting edges, meaning the crack initiation was delayed. This result was not affected by lubrication, although appropriate lubrication is preferred to enable a longer lasting die in terms of wear, which results from the presence of adhesive as the sheet metal is blanked. In the comparison of diameter measurement, the push-back die, combined with the back pressure from the knock-out plate showed a favorable precision. The use of the push back die with a fixed stripper plate, with a $4.5\%$ clearance, showed better accuracy in the diameter measurement. For comparing camber height, the push back die resulted in less cambering than the drop-through die. Also, the larger the clearance, the greater was the camber height. Considering experimental results, the shearing of anti-vibrational sheet metal is best achieved when the rubber is laying on the top, blanked with a fixed-stripper plate in a push-back die, with a $4.5\%$ clearance.

• Rubber Technology
• /
• v.22 no.2
• /
• pp.119-149
• /
• 2021

Domestic materials & components industry is making a shift from quantitative growth to qualitative growth, while the paradigm of a future society is changing rapidly to energy, mobility, smartification and etc. The main features of materials & components industry are analyzed broadly based on three aspects that are: ① industry Status, ② the value chain structure, ③ the competitiveness. With regard to the national aspect, it is shown that the number of an export and a trade surplus increased consistently after the government advanced the policy on materials & components and Korea's trade deficit with Japan has been decreased. Moreover, the state's export ranking increased from tenth place in 2001 into sixth place in 2017, dedicating to the growth of a national economy. The analysis of the chain value indicates that specifications of an end product are set when the materials & components are combined with manpower, infrastructure and technologies. In terms of the competitiveness, it requires a long time and high costs to develop technologies on materials and it is important for components to have a process innovation and credibility wired. Following the industry structure with priority given on materials, Jeonnam Province accounts for 14.8% of national material production. As a result of analyzing Jeonnam's export competitiveness, it is measured that a serious polarization exists, revealing there are 6 major technology industries by 11 categories for materials & components, Jeonnam has presented 6 major materials & components considering the key industry and the new industry in future to remedy the mentioned problem so far, and plans to knock on the industry development through 10 different strategies.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.3 no.2
• /
• pp.227-239
• /
• 1993

The author selected 77 dust emissing processes from 71 types of industries which placed in Sasang Industrial Complex in Pusan. The level of total dust was measured as areal concentration and personal exposure concentration by low volume air sampler and personal air sampler, respectively. Collected samples were classified into 5 groups (chemicals and rubber product, metal product, sawmills and wood, foundries and others). Respirable particulate and total dust of areal and personal exposure were analyzed. The results were as follows; 1. All of the respirable dust concentration and total dust of areal and personal concentration were log-normally distributed. 2. Geometric mean of respirable particulate of personal exposure concentration measured $0.55mg/m^3$ in the first group, $0.86mg/m^3$ in the second group, $0.39mg/m^3$ in the third group, $0.81mg/m^3$ in the forth group and $0.52mg/m^3$ in the fifith group. The exceed rates over TLV (thehold limit values) of total dust were 31.3% in the first group, 31.3% in the second group, 70% in the third group, 80% in the forth group and 13.3% in the fifth group. 3. There were singnificant difference between areal and personal exposure concentration and personal exposure concentration was higher than that of area. 4. In the case of high ratio of respirable particulate to total dust, pneumoconiosis incidence was high even though the workshop was opened and emissing dust concentration was low. These findings suggest that it is desirable to measure respirable particulate in environmental assessment of dust emissing workshops.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.4
• /
• pp.321-327
• /
• 2012

To evaluate whether or not their product is in conformity with its drawing, today's factories manufacturing rubber and/or plastic products use manual process. In manual conformity inspection process, a person decides conformity as comparing drawing to image of product with his eyes. The manual process is tedious and time-consuming in addition that it is impossible to automatically record various informations related to inspection. To solve such problems, this paper proposes automatic drawing conformity inspection system based on computer vision technologies such as image feature matching and bilinear interpolation. The test results show that proposed system is a lot faster when comparing with manual system.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.39-48
• /
• 2006

A laboratory investigation was conducted wherein smooth, rounded, siliceous river gravel aggregates were coated with fine-grained polyethylene, carpet co-product, or cement + styrene butadiene rubber latex and used to prepare hot mix asphalt concrete specimens. Only the coarse (+ No.4) aggregates were coated. The concept was that the coatings would enhance surface roughness of the aggregates and, thus, produce asphalt mixtures with superior engineering properties. Hot mix asphalt specimens were prepared and evaluated using several standard and non-standard test procedures. Based on experiences during the coating processes and analyses of these limited test results, the following was concluded: All three aggregate coating materials increased Hveem and Marshall stability, tensile strength, and resilient modulus(stiffness). These findings are indicative of improved resistance to rutting and cracking in hot mix asphalt pavements prepared using coated gravel aggregates in comparison to similar uncoated gravel aggregates.

• Elastomers and Composites
• /
• v.35 no.2
• /
• pp.138-148
• /
• 2000

In order to investigate the possibility of EPDM micro cellular pad (MCP) as an impact sound insulation product, we studied static/dynamic properties and vibration transfer characteristics of EPDM MCP depending on shape, thickness, degrees of foaming by using material test system (MTS) and lab scale mock-up test apparatus. Static/dynamic rigidity is increased when shape is simple. thickness and degrees of foaming low. We could see that dynamic stiffness is proportional to the transmissibility of EPDM MCP. When dynamic stiffness is increased, characteristic peak at transmissibility curve moves high frequency range or snows increase of maximum value of transmissibility. For lab scale mock-up test and finite element method, EPDM MCP shows low vibration velocity and superior mode shape to just concrete plus slab structure. We could confirm that possibility of EPDM MCP as a impact sound insulation product is high.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.322-330
• /
• 2009

Traffic congestions in local cities have been getting worse since 1990s, so many local governments have considered the introduction of an LRT system. So far, there is no city operating the LRT due to social environments, financial reasons, feasibility and so on. But still many cities have examined LRT or started the construction. Until now, more than 30 cities are constructing LRT or planning the introduction of LRT and it becomes 96 routes, approximately 700km. With the support of MLTM, KRRI has developed automatic LRT system with rubber-wheels, K-AGT as a result of "LRT system technology development project" from 1999 to 2005 by investing 50.32 billion wons(the public 37, the private 13.32) and finished running durability test of 100,000km at Kyeong-san test line. Currently, two trains, coupled two cars respectively have running and signaling tested. K-AGT was appointed to supply for an extension line at Busan Subway Line 3(Minam-Anpyeong section) with 17 trains(six-unit car) 102 cars. However, except for Minam-Anpyeong section, other cities such as Uijeongbu, Yongin, Daegu(Line 3) and Kwangmyeong decided to use the foreign systems, not to use the product, a result of national R&D project. This results in a huge waste of foreign currency and it is expected to require much additional cost for maintenance. If local governments use the products of national R&D projects, many national benefits such as reducing imports and protecting home industries could be expected, therefore in this paper, some plans to encourage to use products of national R&D projects were dealt with.