• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2001.09a
• /
• pp.331-338
• /
• 2001

Seismic performances of the base isolated model of Five Story Stone Pagoda were studied through shaking table tests. Friction pendulum system (FPS), Pure-friction system with laminated rubber bearing (LRB) and Ball with rubber bearing were selected fur the comparison of performances. Performances of specially designed isolation systems were tested dynamically using shaking table. The test results of isolated model are compared with those of fixed base model. Compared with fixed base model, the isolated model showed that it could withstand much higer intensity of earthquake motion. The Effective Peak Ground Acceleration (EPGA) value of isolated model when the top component tipped over was above twice of that value in case of fixed base model. According to the additional test results, the lower value of coefficient of friction than that of common frictional base isolation systems is more effective to protect the piled multi-block system of Pagoda against moderate intesity of ground motion.

• Elastomers and Composites
• /
• v.55 no.3
• /
• pp.229-234
• /
• 2020

Automobile wiper blades are generally treated with chlorine to lower their friction coefficient with the windshield surface. This treatment could affect the crosslink density measurement of rubber vulcanizates, a material used in windshield wipers, which would consequently alter its chemical and physical properties. Therefore, this study evaluated the influence of chlorination on crosslink density measurements of natural rubber (NR) vulcanizates using a vehicle wiper blade. A method for determining the degree of chlorination was developed where the interaction parameter between the rubber and the swelling solvent was corrected. A decrease in the rubber sample swelling ratio was observed upon chlorination, and the chlorination penetrated less than 1% of the sample thickness. The chlorinated NR was assumed to be chloroprene rubber (CR), which was used to correct the interaction parameter. The results showed the CR contributed approximately 7% to the parameter.

• Elastomers and Composites
• /
• v.50 no.4
• /
• pp.258-264
• /
• 2015

Rubber composites were prepared by precured CIIR pulverized at knead shear force in order to research the effects of the BR/PCP composites. The particle size of domain in BR/CIIR composites was decreased and homogeneously dispersed by the precured CIIR pulverized. However, it was difficult to use the product when the content is 40 phr and precured of 40%. BR/PCP composites have improved mechanical properies as compared that of the addition of simply cut chip composite.

• Elastomers and Composites
• /
• v.53 no.4
• /
• pp.234-238
• /
• 2018

The influence of reinforcing UHMWPE powder on the tribological and mechanical properties of HDPE was investigated. The circularizing of UHMWPE powder was improved by high-speed rotation to enhance particle distribution and flowability. HDPE composites reinforced with UHMWPE powder in the range of 0-50 wt% were prepared by co-rotating twin screw extrusion. The abrasion resistance, plane friction coefficient, tensile strengths, and impact strengths of the composites were investigated as a function of the UHMWPE content. An increasing UHMWPE content decreased the plane friction coefficient and increased the abrasion resistance and impact strength. It is expected that HDPE composites reinforced with spherical UHMWPE powder particles can be used to improve the durability of products such as pipes in the future.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.12
• /
• pp.1357-1365
• /
• 2009

In this study, we enhance the numerical approach of Lee et al.$^{(1)}$ to spherical indentation technique for property evaluation of hyper-elastic rubber. We first determine the friction coefficient between rubber and indenter in a practical viewpoint. We perform finite element numerical simulations for deeper indentation depth. An optimal data acquisition spot is selected, which features sufficiently large strain energy density and negligible frictional effect. We then improve two normalized functions mapping an indentation load vs. deflection curve into a strain energy density vs. first invariant curve, the latter of which in turn gives the Yeoh-model constants. The enhanced spherical indentation approach produces the rubber material properties with an average error of less than 3%.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.10
• /
• pp.1125-1131
• /
• 2009

O-rings are commonly used in machines as a seal. Due to prolonged use the surface of an O-ring can degrade which can lead to leakage as well as contamination. Damage of O-rings used in vacuum applications such as sputter is caused by various mechanisms. Particles detached from the O-ring may cause significant problems on the performance of the system in the vacuum chamber. Therefore, understanding the tribological behavior of O-rings is important to tackle the damage caused by repeated contact. In this work, FKM rubber was used for friction and wear tests conducted to investigate the tribological behavior of O-rings. A reciprocating type of a tribo-tester was used for the tests. The friction coefficient between the steel ball and the FKM specimen was quite high. Also, in order to identify the wear behavior, the surface of the FKM specimen was characterized using both optical and scanning electron microscopes. Evidence of wear due to adhesion and extrusion could be found. The results of this work will aid in improving the durability of O-rings.

• Science of Emotion and Sensibility
• /
• v.15 no.2
• /
• pp.177-182
• /
• 2012

Automotive sub-mat carpet for convenience and comfort of floor administration is additional supplemented floor mat. Sub Mat Backing of the current vehicle's materials reclaimed rubber, PVC, etc. are used, but secondary rubber and PVC Backing have bad sound absorption. Also rubber is heavy too. Contact surfaces between PET staple fiber, PET non-woven, PVC backing and car's floor carpet was measured the coefficient of friction for each sub-mat's non-slip evaluation. A surface of PET non-woven sub-mat has the highest coefficient of friction. Each of sample was observed by optical microscope the contact surfaces before and after. Contact surfaces of PET staple fiber sub-mat was changed increasingly to non-woven. This fact is shown that the sub-mat would be tangled between its contact surface and top of the floor carpet. It is expected to be highly non-slip. In case of PET non-woven sub-mat had not different for contact surfaces between before and after. And PVC backing was shown lower non-slip than other samples. The result of optical microscope and coefficient of friction is seems to be related.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1197-1202
• /
• 2010

We have studied on the frictional characteristics for mounting rubbers varieties structures on the automotive engine. This paper are using a test apparatus developed in the laboratory, friction and wear characteristics of various rubbers have been analyzed by experimental study. Frictional characteristics has been measured from the normal force and friction force under various operating conditions, such as, loads, speed and temperatures. Therefore, the rubbers are used in a several varieties structures as well as automotive, the relations between the various conditions and frictional characteristics have been investigated.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1894-1904
• /
• 2011

The Light Rail Transit (LRT) System which has medium transport capacity between subway and bus(5,000-25,000 persons per hour) is the most advanced transportation system. It has many benefits, cheap construction, operational costs through driverless and flexible route planning. Also, the rubber tired AGT (K-AGT) of various LRT has a rubber wheels and side guide. The side guide type has an many advantages. but occur a vibration and friction noise through contact between guide rail and wheel. Most of point that decreased comport is vibration thorough the guide contact. In this paper, It is purpose to improve the maximum running speed of rubber tired AGT localization bogie which is currently developed from 70km/h to 80km/h. To satisfy comport index of railway vehicle that is required in performance test. we examined coefficient of bogie suspension which is designed.

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.257-262
• /
• 2020

Vehicle wiper blades are typically treated with chlorine to lower their friction coefficient with the windshield surface. In this study, a chlorinated, natural rubber (NR) vehicle wiper blade was characterized using a pyrolytic technique. Unchlorinated and chlorinated wiper blades were pyrolyzed and the pyrolysis products were analyzed using gas chromatography/mass spectrometry (GC/MS). Besides isoprene and dipentene, the other principal pyrolysis products such as 1,5,8-p-menthatriene (MTT) and p,α-dimethylstyrene (DMS) were observed. The MTT and DMS ratios did not vary for the chlorinated nor unchlorinated samples when the entire rubber lip of the wiper blade was pyrolyzed. However, when only the lip surface of the wiper blade rubber was pyrolyzed (via scratching with a knife) the relative ratios of the chlorinated sample were much greater than those of the unchlorinated sample. As MTT is produced from the conjugated backbone of chlorinated NR that forms through HCl elimination during initial pyrolysis, and DMS is generated by the dehydrogenation of MTT, these two products could be used as markers for detecting chlorinated NR.