• Journal of Environmental Science International
• /
• v.10 no.4
• /
• pp.311-314
• /
• 2001

The asphalt mixture with CRM(Crumb Rubber Modifier) is known to show a better performance in resisting thermal cracking, fatigue cracking and rutting compared with the conventional mixture. The laboratory tests on the physical characteristics of indirect tensile strength, density, flow and Marshall value of the CRM asphalt were conducted. The test results show that CRM asphalt has better physical characteristics than that of conventional asphalts. And the analysis on the noise reduction effect, penetration capacity from the field test on the national road in Haksan of Chungbuk, and recycling of tire waste were conducted. From this study, the results show that 1% CRM asphalt has higher the noise reduction effect and penetration capacity that those of conventional asphalts. And, optimal contents of crumb rubber modifier in the asphalt binder is one percent. In this case, crumb rubber modifier were used 10 kg to make the asphalt binder of one cubic meter. So it was named as Eco-asphalt.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.553-556
• /
• 2003

This study is analyzed about the factor of adhesive strength characteristics, curing time, asphalt application, test temperature which are liquid waterproofing membrane of rubber-asphalt and chloroprene-rubber type for concrete bridge deck. According to the results, curing time is shorter, adhesive strength is less in chloroprene-rubber type. And also chloroprene-rubber and rubber-asphalt type are showed high adhesive strength in low temperature.

• International Journal of Highway Engineering
• /
• v.11 no.3
• /
• pp.33-40
• /
• 2009

The use of the crumb rubber as an asphalt binder modifier may contribute to road maintenance and repair. The adhesion properties of the crumb rubber modified asphalt (CRMA) sealant have attracted interest due to brittle and adhesion failure of asphalt binders at low temperatures. In this study, the influence of a flexibilizer as a modifier for CRMA at low temperatures was investigated. Their properties were measured using the penetration, the softening point, the tensile and tensile adhesion tests at low temperature. The tensile adhesion strength and the strain of CRMAs were increased with increasing ductile deformation of the CR and the asphalt binder in the flexiblizer modified CRMAs. It was found that the flexibilizer concentration was an important factor for tensile and adhesion properties of CRMAs at low temperatures.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1998.10a
• /
• pp.180-185
• /
• 1998

The study was conducted to evaluate the fundamental properties of waste tire asphalt concretes using polymer modified hinder that were made by dry process. The specimens of four types of polymer modified asphalt concretes were prepared, then Marshall test and indirect tensile strength tests were performed on these samples. The results showed that polymer modified waste tire rubber asphalt concrete was acceptable for the material of asphalt pavement surface layer.

• Elastomers and Composites
• /
• v.43 no.2
• /
• pp.72-81
• /
• 2008

Nowadays, modifying asphalt to improve the resistancy of plastic deformation or rutting on roads has been drawing attention. In this study, asphalts were modified with modifying agents and ground rubber from waste tire (GRT), and the effects of modifier and GRT on the properties of asphalt were analyzed. The Marshall stability of modified asphalt was increased by 98% and the tensile strength increased by 43% compared to straight asphalt. GRT played an important role in enhancing these properties. Viscosity tests, penetration tests and TMA analysis showed the deformation resistancy of modified asphalt. IR and GPC tests indicated that asphalt and modifier have similar chemical structures to each other, and chemical bonding between asphalt and modifier have occurred so that the molecular size lengthened.

• Geomechanics and Engineering
• /
• v.36 no.1
• /
• pp.39-50
• /
• 2024

Bitumen and high-quality subangular aggregates, the two principal materials used for asphalt concrete construction, are finite and expensive materials. The general availability of crumb rubber and naturally occurring aggregates of different shapes, especially flat and elongated shapes, indicates that they are feasible alternative materials for expanding the volume of bitumen and utilizing a wider range of aggregate shapes for the development of asphalt concrete, with an associated environmental benefit. The study investigated the effect of adding up to 15% crumb rubber and aggregates sorted into different groups, i.e., rounded, elongated, flat, and their combinations, on the rheological and mechanical properties and durability of 50/70 of hot-mix asphalt pavement. The addition of crumb rubber decreased ductility and penetration but increased the softening point. For a 5.5% bitumen content, asphalt concrete briquettes consisting of 7% crumb rubber and three types of aggregate shapes, i.e., 100% rounded, a mix of 75% rounded and 25% elongated, and a mix of 75% rounded, 15% elongated and 10% flat, were associated with high Marshall stability and indirect tensile strength as well as low lateral deformation due to their high solidity and moderate angularity ratio. Also, the addition of 7% crumb rubber resulted in a significant improvement in the tensile strength ratio and rebound strain of briquettes consisting of 75% rounded and 25% elongated aggregates and those with 75% rounded, 15% elongated and 10% flat aggregates. In relation to the parameters investigated, the three groups of briquettes met some of the local (South Africa) requirements for the surface course and base course of low traffic volume roads.

• Elastomers and Composites
• /
• v.50 no.4
• /
• pp.304-313
• /
• 2015

In this study, the anionic emulsified asphalt was prepared by dispersing asphalt particles evenly into water with combination of anionic and nonionic surfactants. Effects of NaOH and $CaCl_2$ on the phase stability of the emulsified asphalt were also investigated through zeta potential value and rheology behavior; the emulsified asphalt added with NaOH and $CaCl_2$ showed higher zeta potential value than that the asphalt with addition of only anionic and nonionic surfactants. In addition, with regard to shear thinning behaviors, it was found that pH of the emulsified anionic asphalt and $Ca^{2+}$, counter ion, affected the phase stability. SBR (styrene-butadiene-rubber) latex, EPD (water dispersed Epoxy), PU (polyurethane) and RI-10S, SBS (styrene-butadiene-styrene)-based property improvement additive, were used and studied to enhance the adhesion properties with the aggregates. RI-10S, however, was found to be only compatible with the anionic emulsified asphalt; the coating rate, adhesion and compression strength were increased with the RI-10S content.

• International Journal of Highway Engineering
• /
• v.2 no.1
• /
• pp.123-133
• /
• 2000

The asphalt mixture with CRM(Crumb Rubber Modifier) is known to show a better performance in resisting thermal cracking, fatigue cracking, and rutting compared with the conventional mixture. In this research, the lab tests on the physical and the mechanical characteristics of the domestic crumb rubber modified asphalt binder and conventional asphalts (AP-3, AP-5) were conducted. The physical test results show that CRM asphalt has better physical characteristics than that of conventional asphalts. The dynamic shear rheometer test results in high temperature show that CRM asphalt has higher complex shear modulus and aging resistance than those of conventional asphalts. And, the bending beam rheometer in low temperature test results show that CRM asphalt has higher resistance to thermal cracking than that of conventional asphalts.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.335-344
• /
• 2019

In this work, styrene butadiene rubber (SBR) and styrene butadiene styrene (SBS) were used to modify asphalt, resulting in SBR- and SBS-modified asphalt, respectively. The two modified asphalts were emulsified with a nonionic emulsifier (Span 60) and cationic emulsifiers (ID, DDA) and their phase stabilization was investigated via particle size, Zeta potential, and flow behavior analysis. With increasing amount of the mixed emulsifier, the particle size decreased, leading to an increase in viscosity. The shear thinning behaviors and Zeta potential values ranging from 35-65 mV were determined and remained considerably stable. In addition, the adhesion strength and compression strength of the SBR-and SBS-modified asphalt emulsion were evaluated via surface free energy examination. The remarkable adhesion and compression strengths were estimated when 5 phr ID and 6 phr DDA were added to the emulsified asphalt modified with SBR and SBS. Therefore ID and DDA, the two cationic surfactants, played significant roles in improving the dispersion and interfacial adhesion strength, resulting in the improved adhesion and compression strength of the emulsified asphalts modified with SBR and SBS.

• Elastomers and Composites
• /
• v.27 no.3
• /
• pp.174-182
• /
• 1992

Main components of manufactured sealant were vinylester resin, polybutadiene rubber, asphalt and inorganic filler. For manufactured sealant, liquid and cure properties were tested experimantally. It showed better mechanical properties at rubber content $5{\sim}15phr$. Blown asphalt represented better properties than streight asphalt, showed the highest cohesive strength at asphalt content $6{\sim}8phr$. Appropriate usage of filler was $60{\pm}2%$ of total components, and $Al(OH)_3$ showed better flame-retardancy than $CaCO_3$.