• Progress in Superconductivity and Cryogenics
• /
• v.3 no.2
• /
• pp.1-4
• /
• 2001

For the practical use of a superconducting wire to magnet application, it is important to assess the Young modulus and other mechanical properties of HTS tapes. In order to establish a test method of mechanical properties for oxide composite superconductors. tensile tests of Bi-2223 multi- filamentary tapes were carried out at room temperature, as an activity of the International round robin test proposed by the committee of VAMAS/TWA 16-Subrgroup. The tapes consisting of mutli-filamentary showed a three stage tensile behavior. At the initial stage of the stress-streain curve. The elastic deformation existed in a quite nattrow strain region. But the plastic deformation was observed in a wide strain region due to the platic flow of the Ag alloy matrix. The results of RRT were also reported and discussed.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 1999.02a
• /
• pp.39-42
• /
• 1999

The characteristics of Nb3Sn strands shich will be used for the been investigated. The physics requirements for the KSTAR operation demands the two conditions, high non-Cu critical current density and low contradictory to each other. It is recent that superconductor manufacturers. IGC and Mitsubishi, have succeded in the production of the strand which satisfies the ITER HP-1 and HP-2 conditions at the same time. It has been determined that this type of strand, so-called HP-3, will be used for the KSTAR magnets and its properties, critical current density and hysteresis loss investigated by the several institutes are presented here. On the basis of the round robin tests for many strand samples under various optimized and the vendor will be seleted.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1362-1365
• /
• 2008

ED-2523 (Measuring methods for matr ix reflective LCD modules) was published by JEITA (Japan Electronics and Information Technology Industries Association) in 2001. Since then, round robin tests had been done and the accuracy of measurement values had been discussed. In this paper, considerations for error factors in four measurement systems are showed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.12B
• /
• pp.2003-2015
• /
• 2000

본 논문에서는 ATM 망을 구성하고 있는 노드(node) 간의 셀(cell) 전송시에 출력 링크(output link)로 전송된 셀이 수신 노드에서 수행하는 UPC/NPC에 의해 손실되지 않는 트래픽 정형화기(shaper)를 제안한다. 제안한 정형화기는 비실시간 가변비트율(nrt-VBR) 트래픽을 대상으로 한 것으로 각 ATM 연결(connection)에 대해 독립된 큐(queue)를 할당하였으며, 출력 링크로 전송할 셀을 저장하고 있는 큐를 선정하기 위해 모든 큐에 대해 Generic Cell Rate Algorithm(GCRA)를 수행하여 큐의 상태를 결정하고, 그 결과 전송 가능 상태에 있는 모든 큐들을 대상으로 본 논문에서 제안한 시간의존 확률적 스케줄링(time-dependent probability scheduling) 알고리즘을 적용하여 특정 큐를 선택하여 셀을 전송한다. 제안한 정형화기의 성능평가를 위해 WRR(Weighted Round Robin) 스케줄링 알고리즘을 사용한 정형화기 및 WFQ(Weighted Fair Queueing) 스케줄링 알고리즘을 적용한 정형화기에 대한 모의실험을 하였으며, 그 결과 제안한 정형화기는 비실시간 가변비트율(nrt-VBR) 트래픽의 정형화(shaping)에 우수한 성능을 나타냄을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1300-1302
• /
• 1998

Residual resistance ratio ( RRR ) of Cu/Nb-Ti Superconductor wire was evaluated by fixed point method. Our measured value of RRR showed good consistency with the average value obtained from round robin test conducted by IEC/TC 90. Our test results showed that the coefficient of variation ( COV ) was kept within 2 %

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.1
• /
• pp.53-60
• /
• 1995

The aims of this study are to evaluate the measurement capability of the electromagnetic power and to understand the current state of standard maintanance of the eight participants among the thirteen national calibration and test organizations. The calibration factors were measured at six test frequencies, 50, 100, 500, 1000, 5000, 10000 MHz by organizations and KRISS on the basis of round robin test. The results were analyzed by calculating the standard deviation of the measured values from the standard values. The analysis shows good agreement within 1.0% for all participants at the measurement frequencies. Therefore, the measurement capability of all participants is good in the frequency range of 50 MHz to 10 GHz. For the four participants which specified standard deviations of repeated measurements in their reporst, the total uncertainties is less than 1.9% at the measurement frequencies.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.5
• /
• pp.55-64
• /
• 1996

This paper presents performance evaluation of a new high speed inter-processor communication(HIPC) network for large capacity and high performance digitral switching system. The HIPC structure implements the fast reservation and concurrent arbitration technique (modified round-robin arbitration). The performance evaluation of HIPC was performed by not only computer simulation but also numerical approximation method which was derived for a single server multi-queue system with nonexhaustive cyclic service. The approximation results are almost same with that of computer simulation. The TDX-10 basic callscenario was applied to the HIPC netowrk and analyzed. these results were compared with TDX-10 IPC and shows that the difference of th emean waiting time in the TX buffer of NTP node increases sharply according to the increase of the message arrival rate.

• ETRI Journal
• /
• v.39 no.1
• /
• pp.13-20
• /
• 2017

A method is proposed for scheduling sensor accesses to the shared network in a networked control system. The proposed method determines the access order in which the sensors are granted medium access through minimization of the state estimation error covariance. Solving the problem by evaluating the error covariance for each possible ordered set of sensors is not practical for large systems. Therefore, a convex optimization problem is proposed, which yields approximate yet acceptable results. A state estimator is designed for the augmented system resulting from the incorporation of the optimally chosen communication sequence in the plant dynamics. A car suspension system simulation is conducted to test the proposed method. The results show promising improvement in the state estimation performance by reducing the estimation error norm compared to round-robin scheduling.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.240-245
• /
• 2001

Ultrasonic inspection system is consisted of the operator, equipment and procedure. The reliability of results in ultrasonic inspection is affected by its ability. Furthermore, the reliability of nondestructive testing is influenced by the inspection environment, other materials and types of defect. Therefore, it is very difficult to estimate the reliability of NDT due to various factors. In this study, the probability of detection, used logistic probability model and Monte Carlo simulation, estimated the reliability of ultrasonic inspection. The utility of the NDT reliability assesment is verified by the analysis of the data from round robin test applied these models.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.246-251
• /
• 2001

The performance demonstration round robin test was conducted to quantify the capability of ultrasonic inspection for in-service and to address some aspects of reliability for nondestructive evaluation. The fifteen inspection teams who employed procedures that met or exceeded ASME Sec. XI code requirements detected the pinping of nuclear power plant with various cracks to evaluate the capability of detection. With data from PD-RR test, the performance of ultrasonic nondestructive inspection could be assessed using probability of detection and length and depth sizing of cracks.