• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.263-266
• /
• 2002

An optical method for surface roughness estimation based on statistical analysis of the light intensity of a scattered laser beam pattern. The method is very simple but has a disadvantage that no more information than the averaged roughness is estimated. In this study a new try was conducted to derive more advanced surface information from the details of the light intensity distribution. Some periodic ripples among the light intensity distribution being assumed to relate with scratch left on the machined surface, a corresponding surface profile is estimated from the ripples using FFT and IFFT algorithm. IFFT technique is used to extract some dominant signal components among the intensity distribution. Compared to the measured profiles by a stylus type surf-tester, the profiles obtained through the proposed method are probably acceptable in a sense of the profile shape. Calibration of the amplitude needs more works in the future.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2002년도 추계학술발표논문집
• /
• pp.36-46
• /
• 2002

The accurate characterization of paper structure may provide critical information for ideal selection of raw materials and papermaking processes as well as for predicting the behavior and the quality of final paper products. In this study, local paper structure and the relationship among the structural parameters, thickness, grammage, apparent density and surface roughness of various handsheet and commercial paper samples were evaluated by using recently developed methods. A new concept of surface roughness was also introduced. The results demonstrate that there is significant overestimation in the measured thickness when using the conventional caliper method that originates from the surface roughness and poor paper formation. A novel non-contact thickness tester, referred to as the twin laser profilometer(TLP), provided results that were not subject to these artifacts and thus provided the local intrinsic thickness and consequently the local intrinsic apparent density.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.292-299
• /
• 1998

The effect of characteristic of surface roughness on friction and sliding wear was studied experimentally with ball-on-disk type wear tester. The test was conducted with specimens those have varying arithmetic mean value, skewness and kurtosis under the condition of different load, sliding speed and lubricant viscosity. The surface of the lower skewness in negative value or the highel kurtosis tends to have low friction for the same arithmetic mean value. There is optimum arithmetic mean value surface roughness for operating variables have load, speed, etc.

• 한국세라믹학회지
• /
• 제47권4호
• /
• pp.290-295
• /
• 2010

This study has been focused on properties of mirror surface grinding technology by ELID(Electrolytic In-process Dressing) for structural ceramics using in high precision structural parts as like semi-conductor manufacturing processes. The experimental studies have been carried out to get mirror surface for grinding of structural ceramics, SiC, $Al_2O_3$ and AlN. Grinding process of the ceramics is carried out with varying mesh type, depth of cut and feed rate using diamond wheel. The machining result of the surface roughness and condition of ground surface, have been analyzed by use of surface roughness tester, SEM, AFM and three dimensional surface profiler measurement system.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.315-319
• /
• 1999

This paper has been considered on the cutting characteristics such as chip formation and surface roughness for Inconel 690 alloy with difficult-to-cut because of high toughness and strength. We have made efforts solving the problem to difficult-to-cut of Inconel by improvement of tool with TiN coating and the selection of optimum cutting condition. We used the CCD camera and the surface roughness tester to observe the chip formation and the state of machined surface by using the improved tool with diamond coating and various cutting condions. We have found that the chip formation showed the tooth shape of tooth blade and the surface roughness was very poor. but it can be better by selection of optimum cutting condition.

• 한국표면공학회지
• /
• 제38권4호
• /
• pp.167-173
• /
• 2005

Surface characteristics of HA(hydroxyapatite) coated dental implant alloy by Sol-Gel method were investigated using potentiostat, ICP, SEM, EDX, EPMA and surface roughness tester. Surface roughness of HA coated specimen by Sol-Gel showed higher than that of PVD coated specimen. Corrosion resistance increased in the order of $1\%$ lactic acid, artificial saliva, $0.5\%$ HCI and $0.9\%$ NaCl solution. Amount of Ca element release was higher than that of V and P in the $0.5\%$ HCI and $0.9\%$ NaCl solution.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.54-57
• /
• 2002

In order to find the effect of lubricant viscosity, sheet surface roughness, tool geometry, and forming speed on the frictional characteristics in sheet metal forming, a sheet metal friction tester was designed and manufactured and friction tests of various sheets were performed. Friction test results showed that as the lubricant viscosity becomes lower, the friction coefficient is higher. When surface roughness is extreme1y low or high, the friction coefficient is high. As punch comer radius and punch speed are bigger, the value of friction coefficient is smaller. The sensitivity of friction coefficient is mainly governed by lubricant viscosity and sheet surface roughness.

• 열처리공학회지
• /
• 제4권2호
• /
• pp.27-37
• /
• 1991

The adhesion strength of TiN films to substrate(STC 3) steel has been studied using the scratch adhesion test. Before deposition, the substrates were mechanically polished and TiN films were deposited at different substrate temperature($480^{\circ}C-540^{\circ}C$). The chemical properties of TiN films were investigated by RBS, and EDS, and the physical properties were investigated by micro-hardness tester, SEM, and X-ray diffractometer. According to results of this study, the adhesion strength of TiN films increase with increasing the deposition temperature. The roughness of the polished substrates surface were measured with a profilometer. It was observed that, as a general rule, the adhesion strength of deposited TiN films increase with decreasing the substrates surface roughness.

• 접착 및 계면
• /
• 제21권1호
• /
• pp.27-33
• /
• 2020

유리섬유강화 복합재료 (GFRC)의 표면거칠기에 따른 에폭시 접착제의 접착강도를 평가하였고 최적의 표면거칠기를 선정하였다. 서로 다른 입자크기의 알루미나 (Al2O3) 입자를 GFRC의 표면에 분사하였고 이를 통하여 서로 다른 표면거칠기를 부여하였다. 표면거칠기를 정량화 하였고 표면거칠기에 따른 표면관찰을 진행하였다. 각 표면거칠기에 따른 접촉각을 측정하였고 이를 통하여 표면에너지를 계산하였으며, 에폭시 접착제와의 접착일을 계산 및 비교하여 접착력을 예측하였다. 단일랩전단 시험을 통해 접착강도를 평가하였고 거칠기에 따라 접착강도가 증가된다는 것을 확인하였다. 박리 후 표면을 관찰해 보았을 때 기지재인 GFRC의 박리 정도가 다른 것을 확인하였고 최종적으로 표면거칠기의 최적조건을 확인할 수 있었다.

• 한국산학기술학회논문지
• /
• 제16권2호
• /
• pp.940-946
• /
• 2015

선삭작업에서 가공 여유각 변경은 가공특성을 변화시킨다. 본 연구에서는 피삭재로 기계구조용탄소강, 크롬믈리브텐강, 스테인리스강을 선택하여 정해진 가공조건으로 재질들의 특색이 어떻게 변화하는지 나타내었다. 피삭재의 재질별 표면거칠기를 알아보기 위하여 촉침식 표면 거칠기 측정기로 측정한 결과 인장강도가 높은 피삭재가 표면거칠기 값이 좋게 나왔다. 또한, 가공 이송속도 0.07 mm/rev와 0.10 mm/rev를 비교하였을 경우, 0.07mm/rev일 때가 재질과 관계없이 표면거칠기가 매우 좋게 나타났다. 선삭 여유각 변경에 따른 표면거칠기를 종합하여 분석하여 보면 3가지 재질 모두 $0.9^{\circ}$일 때 가장 좋은 거칠기 값을 보였으며 $0.3^{\circ}$일 때 가장 나쁜 거칠기 값을 보였다.