• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.132-145
• /
• 1992

A series of design, theoretical analysis and model test procedures is presented for the development of an axisymmetric stator-propeller system. A preswirl stator is located in front of a propeller in order to improve the propulsion efficiency by cancellation of the slip stream rotational velocity due to the propeller. Model test results show that propulsion efficiency gain due to the symmetric stator-propeller system is about 3% compared to the single propeller. This efficiency gain would increase for full scale application since the pressure drag coefficient of the stator would decrease due to increasement of turbulent intensity behind the hull wake and increasement of Reynolds number.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.6
• /
• pp.9-13
• /
• 2009

In the three axis control of Low Earth Orbit (LEO) satellite by using reaction wheel and gyro, a reaction wheel produces the control torque by the wheel speed or momentum, and a gyro carries out measuring of the attitude angle and the attitude angular velocity. In this paper, the dynamic modelling of LEO is consisted of the one from the rotational motion of the satellite with basic rigid body model and a flexible model, in addition to the reaction wheel model. A robust controller $(H_\infty)$ is designed to stabilize the rigid body and the flexible body of satellite, which can be perturbed due to disturbance, etc. The result obtained by $H_\infty$ controller is compared with that of the PI (Proportional and Integration) controller, which has been traditionally using for the stabilizing LEO satellite.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.373-384
• /
• 1989

The motions of a spinning rotor and a fluid enclosed in its cavity are known to have mutual interactions, which change the frequencies of forced vibrations and cause instabilities. These phenomena are of technical importance for fluid-cooled turbines as well as spin-stabilized satellites or rockets containing liquid fuels. In this paper the characteristics of unstable whirling of a rotor containing a partitioned cavity filled with two kinds of liquids are investigated experimentally. It studies the influence of rotational speed and filling ratio of two kinds of liquids on unstable whiring. As a result, it is found that the whirl velocity is approximately equal to, or slightly lower for large masses of trapped fluid than rotor critical speed. In case of a spinning rotor partially filled with two kinds of liquids the boundary surface plays a similar role to the free surface, and cases unstable forward whirl.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.4
• /
• pp.271-278
• /
• 2010

Small-sized axial fans are used as air cooler for electric equipments. But there is a strong demand for higher power of fans according to the increase of quantity of heat from electric devices. Therefore, higher rotational speed design is conducted, although, it causes the deterioration of efficiency and the increase of noise. Then the adoption of contrarotating rotors for the small-sized axial fan is proposed for the improvement of performance. In the present paper, the performance curves of the contra-rotating small-sized axial fan with 100mm diameter are shown and the velocity distributions at a partial flow rate at the inlet and the outlet of each front and rear rotor are clarified with experimental results. Furthermore, the flow conditions between front and rear rotors of the contra-rotating small-sized axial fan are investigated by numerical analysis results and causes of the performance deterioration of the contra-rotating small-sized axial fan at the partial flow rate is discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.18-24
• /
• 2015

In this study, a $CO_2$ air-conditioning system was investigated with different types of electrically driven compressors, parallel flow type gas cooler, four-pass type evaporator, internal heat exchanger integrated with accumulator, and electric expansion valve. The experimental study was conducted under various operating conditions (ie., different rotational compressor speeds, air inlet temperatures and air velocity coming into heat exchangers). The experimental results showed the cooling capacity was 3.5kW at $35^{\circ}C$ ambient temperature when the vehicle was idle (ie., the worst condition for cooling off the gas cooler). In terms of performance effect of the compressor, the e-RP model had a slightly better cooling capacity and coefficient of performance than the e-GR model under the same test conditions. An experimental equation for optimum cooling-performance control was also suggested based on the results. A high-pressure control algorithm for the super critical cycle was determined to achieve both maximum cooling performance and efficient energy consumption. The results from the experimental equation coincided with those of previous experimental studies.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.2
• /
• pp.121-130
• /
• 2009

An unsteady numerical simulation method for an autorotating rotor in forward flight was developed. The flapping and rotational equations of motion of autorotation are continuously integrated for given time steps, meanwhile the induced velocity field at disc plane is obtained by the dynamic inflow theory embodying the unteadiness. The transitions from arbitrary initial states to equilibrium states were simulated. Steady autorotations as numerical solutions of equations were predicted by using two sources of blade airfoil data. The simulations using airfoil data which were obtained by a two dimensional Navier-Stokes solver in terms of angles of attack and Reynolds numbers have shown good agreements with wind tunnel experimental results.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.12
• /
• pp.1039-1045
• /
• 2016

We investigated the protection capability of a plate against high speed projectiles demonstrating collision and penetration behaviors by finite element analysis. The element erosion method was used for penetration analysis, which showed that the speed of the projectile was slightly reduced by the collision with the protection plate. Protection capability was measured by the projectile's attitude angle change because the damage of our tanks by projectiles was also dependent on the projectile-tank collision angle. When the length of the protection plate was sufficiently long, the projectile was severely deformed and incapacitated. In the case of a small plate, the projectile was deformed only in the collision region. Thus, projection capability was investigated by the change of attitude angle. The effect of collision angle, velocity, and length of the plate on the rotational and vertical velocities of the projectile was investigated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.7
• /
• pp.622-628
• /
• 2011

The purpose of this study was to analyze the vibro-acoustic characteristics of a stiffened rectangular plate at high frequencies. The stiffeners attached along the plate surface were assumed to have rotational and translational stiffness and inertia. The harmonic response of the stiffened plate were predicted and compared using the Rayleigh-Ritz method with two different trial functions - polynomial and beam functions. The variation of the spatially averaged mean square velocity and the modal characteristics with the number of stiffeners were obtained. The use of the beam function ensured fast convergence which was essential for analyzing the high frequency vibration responses. Using the calculated modal characteristics and the Rayleigh-integral, the radiated sound power was predicted, and the effects of stiffeners were investigated. The proposed model can be applied to study optimal layout of stiffeners for minimal noise generation of the stiffened structures.

• Journal of Mechanical Science and Technology
• /
• v.19 no.12
• /
• pp.2205-2212
• /
• 2005

In this paper, the cutting torque of a CNC machine tool during machining is monitored through the internet. To estimate the cutting torque precisely, the spindle driving system is divided into two parts: electrical induction motor part and mechanical part. A magnetized current is calculated from the measured three-phase stator currents and used for the total torque estimation generated by a spindle motor. Slip angular velocity is calculated from the magnetized current directly, which gets rid of the necessity of a spindle speed sensor. Since the frictional torque changes according to the cutting torque and the spindle rotational speed, an experiment is adopted to obtain the frictional torque as a function of the cutting torque and the spindle rotation speed. Then the cutting torque can be calculated by solving a $2^{nd}$ order difference equation at a given cutting condition. A graphical programming method is used to implement the torque monitoring system developed in this study to the computer and at the same time monitor the torque of the spindle motor in real time through the internet. The cutting torque of the CNC lathe is estimated well within an about $3\%$ error range in average in various cutting conditions.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.8
• /
• pp.897-904
• /
• 1999

We have presented the thermodynamic, structural and dynamic properties of liquid pentane isomers - normal pentane, isopentane, and neopentane - using an expanded collapsed atomic model. The thermodynamic properties show that the intermolecular interactions become weaker as the molecular shape becomes more nearly spherical and the surface area decreases with branching. The structural properties are well predicted from the site-site radial, the average end-to-end distance, and the root-mean-squared radius of gyration distribution func-tions. The dynamic properties are obtained from the time correlation functions - the mean square displacement (MSD), the velocity auto-correlation (VAC), the cosine (CAC), the stress (SAC), the pressure (PAC), and the heat flux auto-correlation (HFAC) functions - of liquid pentane isomers. Two self-diffusion coefficients of liquid pentane isomers calculated from the MSD's via the Einstein equation and the VAC's via the Green-Kubo relation show the same trend but do not coincide with the branching effect on self-diffusion. The rotational re-laxation time of liquid pentane isomers obtained from the CAC's decreases monotonously as branching increases. Two kinds of viscosities of liquid pentane isomers calculated from the SAC and PAC functions via the Green-Kubo relation have the same trend compared with the experimental results. The thermal conductivity calculated from the HFAC increases as branching increases.