• Journal of Welding and Joining
• /
• 제8권1호
• /
• pp.43-53
• /
• 1990

The transient temperature distribution in the continuous friction welding 304 stainless steel bars is investigated by experimental and analytical methods. It is calculated by F.D.M. (finite difference method). The heating pressure, the rotational speed and friction coefficient obtained from experiment are used to determine the heat input at the contacting surface. Thermal properties of the workpiece are the function of temperature. The calculated temperature is well coincided with the measured value. The grain size at weld interface is extremely small due to the severe plastic deformation at high temperature, and result of this refined zone reveals higher hardness value. Because the HAZ is very narror about 2-3 mm, welding defects do not occure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.1021-1026
• /
• 2000

The thermal characteristics of high-speed air spindle system with built-in motor are studied. Experiment and finite element method analysis obtain temperature rise and temperature distribution of housing. For the analysis three-dimensional model is built and temperature rise and distribution in thermal steady state are computed for each rotational frequency. Generally. It is said that the heat generation of air bearing is negligible. But it is certain that the heat generation of air bearing can not be negligible especially in high-speed conditions Frequency response test for air spindle system is executed. In case that the heat generation of air spindle system is high, natural frequency of the system becomes lower when it reaches thermal steady-state and it means that the stiffness of air hearing becomes smaller due to the change of bearing clearance. It is shown that the temperature rise of all spindle system causes thermal expansion md induces the variation of hearing clearance. In consequence the st illness of air bearing becomes smaller.

• 대한치과보철학회지
• /
• 제30권2호
• /
• pp.167-189
• /
• 1992

Frictional heat produced by cutting tools during dental implantation procedure may destroy the surrounding bone tissue and regenerative capacity and interfere ossointegration by formation of undifferentiated connective tissue. To study the effect of frictional heat according to various rotational speeds on the regenerative capacity of surrounding bone tissue, 13 ITI HS implants (8 mm) were inserted at 4 mongrel dogs. Temperatures were measured using thermocouple located 6 mm below from the marginal crest and 0.5 mm from the periphery of trephine mill during implant bed preparation. After 4 and 9 months, animals were sacrificed and specimens were examined using x-rays and light microscope. Results were as follows: 1. With drill speeds of 300, 800, 2,000, 3,500 rpm and saline irrigation, temperatures of surrounding bone were decreased from $-2.9^{\circ}\;to\;-1.7^{\circ}C$. Temperature rises of $2.0^{\circ}\;and\;2.1^{\circ}C$ were recorded with a drill speed of 5,000 rpm and irrigation. 2. With drill speeds of 800, 3,500, 5,000 rpm and no irrigation, temperatures of surrounding bone rose from $+1.5^{\circ}\;to\;+6.8^{\circ}C$, but maximum temperature was $40^{\circ}C$ at 5,000 rpm. 3. On radiographic examination, bone resorptions were observed at the upper half of implant of 5,000 rpm without irrigation and one case of 5,000 rpm with irrigation. 4. Osseointegration was unsuccessful in cases of 3,500, 5,000 rpm without irrigation due to fibrous connective tissue formation to the outer surface and hollow, but it was successful in a case of 800 rpm without irrigation. 5. Osseointegration was successful in cases of 300, 800, 2,000 and 3,500 rpm with irrigation. But fibrous connective tissue formation was observed at the hollow of implant inserted with 5,000 rpm with irrigation.

• Journal of Pharmaceutical Investigation
• /
• 제33권1호
• /
• pp.15-19
• /
• 2003

The rheological behavior of poloxamer 407 solution as function of concentration and temperature was evaluated by rotational viscometer. The viscosity of poloxamer 407 solution was increased as the concentration of poloxamer 407 and temperature increased. At $4^{\circ}C$, poloxamer 407 solution showed the Newtonian flow characteristics regardless of concentration. Upon increasing temperature the poloxamer solution changed to the pseudoplastic flow pattern. And at gelation temperature, rheological profiles showed the abrupt increase in viscosity. Gelation temperature was decreased as the concentration of poloxamer 407 increased, while it increased as the concentration of poly(ethylene glycol) 4000 increased. Poly(ethylene glycol) might be expected to reduce the driving force for hydrophobic interaction resulting in slow gelation. From the viscoelastic properties of poloxamer gel system, we obtained the storage and loss modulus depending on the shear stress and frequency. And the sol-gel transition temperature was also obtained from the viscoelastic properties of poloxamer 407 gel.

• 한국산학기술학회논문지
• /
• 제13권11호
• /
• pp.5628-5636
• /
• 2012

본 연구에서는 하수슬러지를 효율적으로 건조시킬 수 있는 방법을 연구하고자 하였다. 슬러지 건조를 위해서는 슬러지 내 대부분의 함수율을 차지하고 있는 세포 내 함유수분을 제거시키는 것이 필요한데, 이에 대한 제거 장치로서 타격기류 건조장치를 적용하였으며, 직접 하수처리장에 파일롯 플랜트를 설치하여 실증실험을 실시하여, 이에 대한 운전특성과 적용가능성을 확인하고자 하였다. 주요 운전제어 변수는 슬러지 투입속도, 체인 회전속도, 공정온도 및 투입슬러지 함수율 변화 등이다. 체인의 회전속도가 증가할수록 생성슬러지 생성수율 증가 등 장치성능이 향상되었고, 공정온도가 상승함에 따라 건조효율이 증가하는 경향을 나타내었다. 투입슬러지 함수율은 60%일 때 생성슬러지 생성수율이 최대이고 함수율도 10% 내외를 나타내어 최적 조건임을 알 수 있었다. 슬러지 투입속도는 적정 투입속도 이상으로 투입 시, 생성슬러지 생산량은 증가하지 않는 반면, 오히려 잔류량만 증가하는 현상을 초래하였다. 위와 같은 실험결과로부터 장치의 최적 운전조건은 체인 회전수 1600rpm(최대속도), 최종 배출온도 $80^{\circ}C$, 투입슬러지 함수율 60%, 슬러지 투입속도 60kg/h이며, 이때 장치성능은 생성슬러지 생성수율 85.5%, 함수율 11.0%, 건조효율 81.7%으로 양호한 결과를 나타내었다.

• 한국결정성장학회지
• /
• 제8권3호
• /
• pp.448-453
• /
• 1998

도립형 OMVPE 반응기를 레이저 라만 분광법을 사용하여 조사하였다. 운반기체인 질소나 수소의 순수한 회전 라만 분산 스펙트럼을 통해 반응기 내부의 축 중심 방향의 온도 분포를 정확히 측정할 수 있었다. 주입 기체의 유속과 반응기의 종횡비가 변수로 변화되었으며 실험결과, 기판 표면 근처의 수직방향 온도 구배를 크게 유지하기 위해서는 보다 빠른 기체 유속의 사용, 보다 큰 반응기 종횡비의 사용, 그리고 질소의 사용이 유리함을 알 수 있었다.

• Tribology and Lubricants
• /
• 제2권1호
• /
• pp.61-68
• /
• 1986

Effects of the ram-pressure on the THD-performance of pivoted pad thrust bearings are investigated experimentally. A sector-shaped tilting pad thrust bearing and a rotating disk are used. Temperature distribution on the disk surface as well as on the pad surface, distribution of the pressure generated within the fluid film, and the film thickness are measured continuously in the circumferential direction after thermal equilibrium is established. The ram-pressure is proportional to the mean pressure of oil film and to the rotational speed of the disk and affects the maximum pressure and the pressure distribution. The temperature rise on the mating surface of the disc and the pad, contacting with the oil film, is proportional to to the bearing load and the disk speed. The ram-pressure and the temperature rise on the disk surface are dominant factors that affect the THD-performance of pivoted pad thrust bearings.

• KSTLE International Journal
• /
• 제4권2호
• /
• pp.43-46
• /
• 2003

Water-lubricated frictional characteristics of a stainless steel ball bearings are not well known compared to the oil-lubricated frictional characteristics. Furthermore a study on friction at a high temperature is rare because the bearing maintenance strategy for water-lubricated or chemicals-lubricated bearings of equipment is generally based on the replacement of the failed bearings-and parts. Ball bearings and ball screw are installed in the power transmission for the newly developing integral reactor and these are lubricated with chemically-controlled pure water at a high temperature and a high pressure. Bearings and power transmitting mechanical elements for an atomic reactor requires high reliability and high performance during the estimated lifetime, and it should be verified. In this paper, experimental research results of the frictional characteristics for water-lubricated ball bearings are presented as a preliminary investigation.

• 한국공작기계학회논문집
• /
• 제16권5호
• /
• pp.70-76
• /
• 2007

The purpose of this study is to analyze the characteristics of a domestic developed hydraulic axial piston motor. An experimental apparatus was constructed and the output torque, the input oil pressure, the input flow rate, the speed of motor and oil temperature were measured. They were measured under both no load and load conditions. The results are as follows; 1. Motion of motor became steady state conditions after 5 seconds. 2. Output torque of motor was proportional to input oil pressure under both load and unload. 3. Speed of motor decreased with increasing load. 4. Oil temperature was almost constant. The results of this study will offer the basic data in designing and operating hydraulic axial piston motors.

• 비파괴검사학회지
• /
• 제32권3호
• /
• pp.291-295
• /
• 2012

In the industrial field, real-time monitoring system like a fault early detection is very important. For this, the infrared thermography technique as a new diagnosis method is proposed. This study is focused on the damage detection and temperature characteristic analysis of ball bearing using the non-destructive infrared thermography method. In this paper, thermal image and temperature data were measured by a Cedip Silver 450 M infrared camera. Based on the results, the temperature characteristics under the conditions of normal, loss lubrication, damage, dynamic loading, and damage under loading were analyzed. It was confirmed that the infrared technique is very useful for the detection of the bearing damage.