• 한국재료학회지
• /
• 제26권11호
• /
• pp.628-634
• /
• 2016

The cold rolling workability and mechanical properties of two new alloys, designed and cast Al-5.5Mg-2.9Si and Al-7Mg-0.9Zn alloys, were investigated in detail. The two alloy sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1 mm by multi-pass rolling at ambient temperature. The rolling workability was better for the Al-7Mg-0.9Zn alloy than for the Al-5.5Mg-2.9Si alloy; in case of the former alloy, edge cracks began to occur at 50% rolling reduction, and their number and length increased with rolling reduction; however, in the latter alloy, the sheets did not have any cracks even at higher rolling reduction. The mechanical properties of tensile strength and elongation were also better in the Al-7Mg-0.9Zn alloy than in Al-5.5Mg-2.9Si alloy. Work hardening ability after cold rolling was also higher in the Al-7Mg-0.9Zn alloy than in the Al-5.5Mg-2.9Si alloy. At the same time, the texture development was very similar for both alloys; typical rolling texture developed in both alloys. These differences in the two alloys can primarily be explained by the existence of precipitates of $Mg_2Si$. It is concluded that the Al-7Mg-0.9Zn alloy is better than the Al-5.5Mg-2.9Si alloy in terms of mechanical properties.

• 한국주조공학회지
• /
• 제21권6호
• /
• pp.336-342
• /
• 2001

This study was carried out to examine the effects of adding 0.3at.%Hf in Fe-30at.%Al-5at.%Cr alloy on the variation of microstructures and hot workability. The effect of hot rolling on mechanical properties was estimated by measuring the elongation and tensile strength after rolling at 800 and 1000 respectively. Microstructure of Fe-30at.%Al-5at.%Cr alloy was consisted of large equiaxed grains and it was changed to quasi-equiaxed or columnar structures by adding 0.3at.%Hf to Fe-30at.%Al-5at.%Cr alloy. Every specimens showed a decreased tensile strength after hot rolling compared to that of before rolling. The elongation was increased by hot rolling. Remarkable changes in elongation by hot rollong was observed such as from 1.4% to 4.5% elongation at the specimen of 0.3at.%Hf added to Fe-30at.%Al-5at.%Cr. Fe-30at.%Al-5at.%Cr alloy showed typical cleavage fracture on tensile failure and hot rolling has negligible effects on fracture mode in this alloy. However at the alloy containing Hf fracture mode was changed by hot rolling from intergranular to mixed intergranular and transgranular fracture mode.

• 소성∙가공
• /
• 제25권1호
• /
• pp.5-11
• /
• 2016

The control of the roll velocities is essential in maintaining stability during ring rolling, but such control is difficult. The determination of the best roll velocities can be helped with the use of FE simulations and processing maps, which give the useful information such as power dissipation and flow instability for hot metal forming processes. In the current study, the workability of 7050 aluminum alloy is evaluated by using processing map. With the developed information, the stability of the ring rolling condition, called the Constant Growth Velocity Condition (CGVC), is evaluated.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.99-101
• /
• 2008

At 21st century, material development concepts were changed to fulfill the environmental friendly demands. This study is to study the effect of pressurized nitrogen gas and manganese in high nitrogen austenitic stainless steel(HNS) in which N and Mn elements substitute the nickel element. 100kg HNS ingots were made by Pressurized Vacuum Induction Melting(P-VIM) and were forged according to free forging process. As forged HNS were hot and cold rolled by pilot scale rolling machine. Depending on the rolling condition, the mechanical properties of HNS were changed. The roll thrust and sheet folding showed asymmetry condition between work and drive side during cold and hot rolling. The purpose of this study are to improve workability the hot and cold rolling machine and to set the conditions for establishing the rolling process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.329-332
• /
• 2008

Nowadays, It is required human body-friendly, good mechanical properties, and economical efficiency material, simultaneously. The material to meet above requirement condition rear up high nitrogen stainless steel(HNS). However, HNS have a lot of problem such as poor workability, hot crack sensitivity. So, It is needed the condition of plastic working to overcome above many problem. In this study, VIM ingot with 100kg was made by pressurized vacuum induction melting. And then, The slab perform for hot rolling was prepared by open-die forging. Hot rolling process was performed by computer simulation according to change of height reduction, rolling temperature, heating numbers, rolling pass and so forth. The results of analysis were investigated between analysis and lab-scale rolling product.

• 열처리공학회지
• /
• 제27권2호
• /
• pp.59-64
• /
• 2014

Cu-Al-Mn shape memory alloys of a variety of composition were characterized in terms of shape memory properties and cold workability. Cold workability tested by cold rolling indicated that the alloys solution treated in the ${\alpha}+{\beta}$ region have a higher ductility than those solution treated in the ${\beta}$ region. Also it is known that cold workability increased with the decrease in Al content in the ${\beta}$ region. This seems to be resulted from the fact that Mn addition causes to expand ${\beta}$ region toward lower Al content and lower order-disorder transition temperature, consequently, ${\beta}$ of excellent workability being frozen even at room temperature. Experimental results regarding shape memory showed that the properties were better with a higher Al contents at a given Mn content, which is closely related with martensitic transformation. It is also shown that super elasticity limit was enhanced with decrease in the yield strength of alloys because a lower yield strength seems to initiates slip at the lower applied stress.

• 열처리공학회지
• /
• 제27권1호
• /
• pp.15-22
• /
• 2014

This study is to investigate the phase changes and cold workability after isothermal transformation at $780^{\circ}C$ by using the high temperature gas nitrided (HTGN) STS 430 ferritic stainless steel specimens. The phase diagram of STS 430 steel obtained by calculation showed that the phase appeared at $1100^{\circ}C$ showed as ${\alpha}+{\gamma}{\rightarrow}{\gamma}{\rightarrow}{\gamma}+Cr_2N{\rightarrow}{\gamma}+Cr_2N+CrN$ with increasing nitrogen concentration. Also, the transformation of ${\gamma}{\rightarrow}Cr_2N$ during heat treatment isothermally at $780^{\circ}C$, nitrogen pearlite with lamellar type was fully formed at the nitrogen permated surface layer for 10 hrs. However, this transformation was not completed for 1 hr, resulting nitrogen pearlite plus martensite. The cold rolled specimen of isothermally transformed at $780^{\circ}C$ for 10 hrs after high temperature gas nitriding decreased the layer thickness of nitrogen pearlite inducing the deformation of hard $Cr_2N$ phase. the dissolution rate of $Cr_2N$ phase increased rapidly with increasing cold rolling ratio. Specimens with the microstructure of nitrogen pearlite (isothermally transformed at $780^{\circ}C$ for 10 hrs) were possible to cold rolling without crack formation. However, the mixed structures of nitrogen pearlite + martensite (isothermally transformed at $780^{\circ}C$ for 1 hr) were impossible to cold deformation without cracking.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.276-279
• /
• 2000

When high temperature superconducting tapes is fabricated using the PIT (Powder In Tube) method, the length of HTS tapes is increased more than 500 ${\sim}$ 1,000 times of initial powder packed billet. On mechanical processing, heterogeneous properties between the ceramic superconducting core and Ag/Ag alloy sheath occur the non-uniformity deformation as like sausaging that deteriorate the critical current properties of HTS tapes. In this study, we investigated the workability of Bi-2223/Ag/Ag alloy sheath tapes fabricated by the PIT method involving a number of different mechanical processes, multi drawing and rolling. In order to obtain the high critical current density and high uniformity of Bi-2223/Ag sheath tapes, the influences of powder packing density, drawing die angle and rolling parameters were studied. We found that the roll diameter is an important variable in the rolling process, as critical current of tapes rolled using 250 mm rolls was higher than that using 150 mm rolls.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.87-90
• /
• 2008

Since fastener bolt for airplane require high specific strength and corrosion resistance, Ti-6Al-4V alloy is widely used. However, the Ti-6Al-4V bolt is generally manufactured by cutting and rolling because of their poor workability. The aim of present work is to develop hot forming technology for high strength Ti-6Al-4V. Various heat-treatments were applied to specimen in order to increase hot-workability and prevent galling with die Multiple forging were simulated with FE code to determine optimum process parameters including specimen temperature, strain rate, local strain, and thermal shrinkage. Forged samples were heat-treated again to increase their mechanical properties.

• 소성∙가공
• /
• 제18권3호
• /
• pp.251-255
• /
• 2009

Since fastener bolt for airplane require high specific strength and corrosion resistance, Ti-6Al-4V alloy is widely used. However, the Ti-6Al-4V bolt is generally manufactured by cutting and rolling because of their poor workability. The aim of present work is to develop hot forming technology for high strength Ti-6Al-4V. Various heat-treatments were applied to specimen in order to increase hot-workability and prevent galling with die. Multiple forging were simulated with FE code to determine optimum process parameters including specimen temperature, strain rate, local strain, and thermal shrinkage. Forged samples were heat-treated again to increase their mechanical properties.