• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.343-348
• /
• 2014

A powder-in-sheath rolling (PSR) process utilizing a copper alloy tube was applied to a fabrication of a multi-walled carbon nanotube (CNT) reinforced aluminum matrix composite. A copper tube with an outer diameter of 30 mm and a wall thickness of 2 mm was used as a sheath material. A mixture of pure aluminum powders and CNTs with the volume contents of 1, 3, 5 vol% was filled in the tube by tap filling and then processed to 93.3% height reduction by a rolling mill. The relative density of the CNT/Al composite fabricated by the PSR decreased slightly with increasing of CNTs content, but showed high value more than 98%. The average hardness of the 5%CNT/Al composite increased more than 3 times, compared to that of unreinforced pure Al powder compaction. The hardness of the CNT/Al composites was some higher than that of the composites fabricated by PSR using SUS304 tube. Therefore, it is concluded that the type of tube affects largely on the mechanical properties of the CNT/Al composites in the PSR process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.1036-1041
• /
• 1997

The objective of this study is to adjust the roll gap for the dimension accuracy of bar in hot bar rolling process considering roll wear. In this study hot bar rolling processes for round and oval passes have been investigated. In order to predict the roll wear, the wear model is reformulated as an incremental form and then wear depth of roll is calculated at each deformation step on contact area using the results of finite element analysis, such as relative sliding velocity and normal pressure at contact area. Archard's wear model was applied to predict the roll wear. To know the effects of thermal softening of DCI (Ductile Cast Iron) roll material according to operating conditions, high temperature micro hardness test is executed and a new wear model has been proposed by considering the thermal softening of DCI roll expressed in terms of the main tempering curve. The new technique developed in this study for adjusting roll gap can give more systematically and economically feasible means to improve the dimension accuracy of bar with full usefulness and generality.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.197-203
• /
• 2004

A full finite element (FE)-based approach is presented for the precision analysis of the strip profile in flat rolling. Basic FE models for the analysis of the mechanical behavior of the strip and of the rolls are described in detail. Also described is an iterative strategy for a rigorous treatment of the mechanical contact occurring at the roll-strip interface and at the roll-roll interface. Then, presented is an integrated FE process model for the coupled analysis of the mechanical behavior of the strip, work roll, and backup roll in four-high mill. A series of process simulation are conducted and the results are compared with the measurements made in hot and cold rolling experiments.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.290-295
• /
• 2009

The roll gap set-up in the finishing mill is one of the most important technologies in the hot plate rolling process. As the target thickness can be obtained by the correct set-up of the roll gap, improving the roll gap set-up technology is very critical for plate thickness accuracy. The main cause of thickness variation in hot plate mills is the non-uniform temperature distribution along the length of the slab. The objective of this study is to adjust the roll gap set-up for the thickness accuracy of plate in hot rolling process considering top-end temperature drop. Therefore this study has concentrated on determining the correct amounts of thickness variation according to top-end temperature drop and roll gap to compensate thickness variation. The control method of roll gap set-up which can improve the thickness accuracy was proposed. The off-line simulation of compensated roll gap significantly decreases top-end thickness variation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.9 s.240
• /
• pp.1270-1275
• /
• 2005

Rolling process to fabricate a strip with even thickness is significant to enhance the quality of the strip. The thickness of a strip can be effectively controlled by pair-cross mills. However, pair-cross mill generates thrust in the axial direction of roller and causes skewness, deflection, twist and even accidental roll chock failure. Therefore, accurate estimation of the thrust of the pair-cross mill during rolling process is necessary to monitor the failure of roll and the quality of products. An empirical equation given by Mitsubishi Heavy Industry (MHI) is hitherto employed, where the thrust is expressed in terms of rolling force, reduction ratio and crossed angle. However it turns out that the MHI empirical equation provides somehow inaccurate and unsuitable thrust in practical rolling processes. Moreover, we learn that three parameters involved in MHI equation are coupled each other. In this paper, axiomatic design principle is employed to select appropriate parameters involved in approximate equation in order to make parameters uncoupled. A quadratic equation using response surface method with new parameters is suggested. The accuracy of the approximate model is examined by comparing with real experimental data.

• Tribology and Lubricants
• /
• v.32 no.1
• /
• pp.18-23
• /
• 2016

The effective case depth for case-hardened rolling bearing has been discussed. For this purpose, rolling contact fatigue tests for ball bearings built with inner race of various hardness values were conducted until L₁₀ calculating rating life using a bearing life test machine under radial loading. Then, the distribution of residual stress below the inner raceway, which depended on the hardness value, was measured by X-ray diffraction. As a result, the linear relationship was established between the hardness value of the inner race and the theoretical shear stress evaluated at the depth where the residual stress disappeared below the inner raceway. Based on the relationship, it could be found that the factor of safety in bearing manufacturer’s rules for the effective case depth of case hardened rolling bearings was set higher. However, it could be also found that the hardness values at the depth where the maximum shearing stress acted below the raceway surface in a tapered roller bearing hardened by the carburizing process, were not sufficient for preventing plastic deformation under the basic dynamic load rating. Consequently, further efforts were still required to reduce or to disperse the contact load on the material design of a rolling bearing in order to prolong its life.

• Journal of Powder Materials
• /
• v.21 no.1
• /
• pp.50-54
• /
• 2014

A powder-in-sheath rolling method was applied to a fabrication of a carbon nano tube (CNT) reinforced aluminum composite. A STS304 tube with an outer diameter of 34 mm and a wall thickness of 2 mm was used as a sheath material. A mixture of pure aluminum powders and CNTs with the volume contents of 1, 3, 5 vol was filled in the tube by tap filling and then processed to 73.5% height reduction by a rolling mill. The relative density of the CNT/Al composite fabricated by the powder-in-sheath rolling decreased slightly with increasing of CNTs content, but exhibited high value more than 98. The grain size of the aluminum matrix was largely decreased with addition of CNTs; it decreased from $24{\mu}m$ to $0.9{\mu}m$ by the addition of only 1 volCNT. The average hardness of the composites increased by approximately 3 times with the addition of CNTs, comparing to that of unreinforced pure aluminum. It is concluded that the powder-in-sheath rolling method is an effective process for fabrication of CNT reinforced Al matrix composites.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.5
• /
• pp.497-502
• /
• 1997

In this study an automatic rolling-coil labeling system using robot vision system and peripheral mechanism is proposed and implemented, which instead of the manual labor to attach labels Rolling-coils in a steel mill. The binary image process for the image processing is performed with the threshold, and the contour line is converted to the binary gradient which detects the discontinuous variation of brightness of rolling-coils. The moments invariant algorithm proposed by Hu is used to make it easy to recognize even when the position of the center are different from the trained data. The position error compensation algorithm of six degrees of freedom industrial robot manipulator is also developed and the data of the position of the center rolling-coils, which is obtained by floor mount camera, are transferred by asynchronous communication method. Therefore, even if the position of center is changed, robot moves to the position of center and performs the labeling work successfully. Therefore, this system can be improved the safety and efficiency.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1437-1443
• /
• 2011

Thick plates produced by the rolling process are used as the basic elements of ship structures. In this paper, we present a setup model for controlling the asymmetric factors causing plate bending in the width direction during plate rolling. A series of three-dimensional finite element analyses is conducted to predict the relationship between various asymmetric factors and plate bending. The setup model is developed by performing regression on the relationship to produce linear equations with several nondimensional parameters. The setup model is verified with a pilot rolling test in which variations in thickness and temperature differences in the width direction exist. The results show that the bending curvatures predicted by the model are in fairly good agreement with the measured results for those asymmetric factors.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.705-711
• /
• 1988

Surface rolling is one of the plastic deformation processes, which improves surface roughness and increases hardness. The surface rolling tool used in this experiment was specially designed by author for surface rolling on cast iron. The cutting feeds were 0.10mm/rev.and 0.30mm/rev.The applied forces of rolling were in the range of 10kgf to 30kgf with 5kgf differences. The results obtained are as follows. (1) In general the good surface roughness can be obtained with the applied force 25kgf according to surface roughness of the previous turning. (2) The hardness is mainly increased at the first rolling process and is more increased with the increasing applied forces. (3) The reduction of the diameter heavily depends on the original surface roughness. That is, the larger surface roughness is, the larger is the reduction is the reduction of diameter.