• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.533-536
• /
• 2008

H 형강은 시공성과 유지관리의 간편성으로부터 교량의 주형과 가설 구조물에 사용하는 경우가 증가하고 있다. 특히 H형강을 교량에 적용하는 경우 지점부의 부모멘트에 의해 지간장 20m 내외가 한계이고, 기존공법의 경우 콘크리트를 사용한 공법에 비해 큰 장점을 가지고 있지 못한다. 따라서 본 연구에서는 교량의 장지간화가 가능한 가로거더공법을 개발하여 기존의 강교량의 문제점을 극복한 장지간 H형강 강합성 교량을 개발하고자한다. 여기서는 수치해석적 방법으로 주형과 주형이 연속화되는 시점을 변화시켜 내하력을 계산하고, 그 결과로 부터 합리적인 가로거더공법을 개발하고자한다.

• 한국강구조학회 논문집
• /
• 제20권6호
• /
• pp.829-838
• /
• 2008

국내 현실에 적합한 내진 접합부 상세 개발과 평가를 위하여 국내 중저층 철골건물에 적용되는 단면을 갖는 보와 기둥으로 구성 된 접합부 실험체를 선정하여 반복재하 실험을 수행하였다. 실험변수는 접합부 형식과 강종이며 새로 개발된 내진용 형강(SHN490)과 기존 형강 (SM490)의 성능 차이를 비교하였다. 소재인장시험결과에 의하면 SHN490 형강의 항복강도와 인장강도의 분포는 SM490형강의 분포보다 균일한 것으로 평가되었다. 접합부 실험체의 용접부에서의 취성파괴는 관찰되지 않았고 소정의 소성변형 능력을 발휘한 후 보 플랜지의 열영향부나 용 접접근공의 응력집중부위에서 파단이 발생하였다. 동일한 강종으로 구성된 실험체의 경우, 보의 웨브가 볼트에 의하여 기둥에 연결된 접합부 (WUF-B)보다는 용접에 의하여 연결된 접합부(WUF-W)의 회전과 에너지 소산능력이 더 컸다. 또한 동일한 접합부 형식의 실험체에서는 SM490 형강으로 구성된 실험체보다는 SHN490 실험체의 회전과 에너지 소산능력이 더 컸다.

• 한국레이저가공학회지
• /
• 제11권2호
• /
• pp.15-19
• /
• 2008

Electron beam (EB) weldability of pure grade Nb sheet was studied. One of Nb sheets was as-annealed and the other was cold rolled. Microstructures, Vickers hardness, and transverse weld tensile test were carried out for the base metal, the heat affected zone (HAZ) and weld metal. In the case of the EB welds made using the annealed Nb sheeet, fine equiaxed grains and coarse grains were dominant at the base metal and the HAZ, respectively, and columnar grains were observed at the weld metal. For the EB welds made using the cold rolled Nb sheet, elongated grains in the rolling direction at the base metal, and the microstructures of the weld metal and the HAZ are similar to those of the EB welds made using the annealed Nb sheet, respectively. For both annealed and cold rolled Nb sheet, the width of the HAZs are unusually wide in spite of using high density heat source, i.e. electron beam, and the grain sizes of both HAZs are similar. When tensile test was carried out using the transverse weld specimens, the failure occurred at the HAZ for both EB welds made using Nb sheets annealed and cold rolled, respectively and the tensile strengths of both specimens were 161MPa. Vickers hardness of EB welds made using annealed Nb was 56-57 Hv at both base metal and weld metal, 52-53 Hv at the HAZ. On the other hand, Vickers hardness of EB welds made using cold rolled Nb was 97-99 Hv at the base metal, but the hardness values of weld metal were similar to those obtained at the weld metal of annealed Nb.

• 한국자동차공학회논문집
• /
• 제24권4호
• /
• pp.379-385
• /
• 2016

Door impact beam plays a key role in minimizing the occupant injury within the side impacted vehicle through preventing intrusion of the impacting vehicle. Steel pipe type door impact beam has been widely adopted since it has simple structure and the overall strength is easily determined according to the pipe size. The brackets welded at pipe ends connect the door impact beam and the door panels by spot welds. In this study, first, the effect of pipe thickness, bracket thickness and door mounting stiffness was respectively analyzed. Next, application of the tailor rolled pipe was examined and several alterations of the bracket mounting method were considered. Application of tailor rolled pipes with superior bracket mounting method showed remarkable strength enhancement and weight reduction possibility in comparison with the current door impact beam.

• Steel and Composite Structures
• /
• 제4권1호
• /
• pp.23-36
• /
• 2004

The inelastic lateral-distortional buckling of doubly-symmetric hot-rolled I-section beam-columns subjected to a concentric axial force and uniform bending with elastic restraint which produce single curvature is investigated in this paper. The numerical model adopted in this paper is an energy-based method which leads to the incremental and iterative solution of a fourth-order eigenproblem, with very rapid solutions being obtained. The elastic restraint considered in this paper is full restraint against translation, but torsional restraint is permitted at the tension flange. Hitherto, a numerical method to analyse the elastic and inelastic lateral-distortional buckling of restrained or unrestrained beam-columns is unavailable. The prediction of the inelastic lateral-distortional buckling load obtained in this study is compared with the inelastic lateral-distortional buckling of restrained beams and the inelastic lateral-torsional buckling solution, by suppressing the out-of-plane web distortion, is published elsewhere and they agree reasonable well. The method is then extended to the lateral-distortional buckling of continuously restrained doubly symmetric I-sections to illustrate the effect of web distortion.

• 복합신소재구조학회 논문집
• /
• 제1권3호
• /
• pp.35-40
• /
• 2010

본 연구에서는 거더와 가로보로 이루어진 패널을 특별직교이방성 판 이론을 응용하여 해석하였다. 거더와 가로보는 H 형단면을 사용하였다. 본 논문에서는 특별직교이방성 판 이론을 압연형교에 응용하였으며 해석한 결과를 제시하였다. 해석결과는 보 이론과 비교하였다. 이러한 목적으로 본 논문에서는 유한차분법을 사용하였다. 고유진동수에 대한 $D_{22}$ 강성의 영향을 철저히 검토하였다. 본 연구에서는 판 이론에 의해 수치해석을 해본 결과 보 이론보다 강성이 2.43배가 되는 것을 알 수 있었다.

• 한국강구조학회 논문집
• /
• 제18권5호
• /
• pp.535-542
• /
• 2006

본 논문에서는 압연형강(H형강)을 이용한 강합성 교량에 대한 3차원 유한요소 해석을 실시하여, 가로보가 활하중 횡 분배에 미치는영향에 대해 검토하였다. 고려된 주요 변수는 주형과 가로보의 단면2차모멘트비, 가로보의 설치 여부, 가로보의 개수 등이다. 유한요소 해석을 통한 활하중 횡분배 계수와 함께 관용적인 격자해석에 의한 활하중 횡분배 계수도 비교하였다. 분석결과에서 가로보는 활 하중 횡분배에 별다른 영향을 미치지 못하며, 콘크리트 바닥판이 활하중 횡분배에는 가장 중요한 역할을 하는 것으로 나타났다. 따라서 활하중 횡분배를 목적으로 설치하는 가로보는 제거가 가능한 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제35권6호
• /
• pp.677-697
• /
• 2010

This paper focuses on geometrically non-linear static analysis of a simply supported beam made of hyperelastic material subjected to a non-follower transversal uniformly distributed load. As it is known, the line of action of follower forces is affected by the deformation of the elastic system on which they act and therefore such forces are non-conservative. The material of the beam is assumed as isotropic and hyperelastic. Two types of simply supported beams are considered which have the following boundary conditions: 1) There is a pin at left end and a roller at right end of the beam (pinned-rolled beam). 2) Both ends of the beam are supported by pins (pinned-pinned beam). In this study, finite element model of the beam is constructed by using total Lagrangian finite element model of two dimensional continuum for a twelve-node quadratic element. The considered highly non-linear problem is solved by using incremental displacement-based finite element method in conjunction with Newton-Raphson iteration method. In order to use the solution procedures of Newton-Raphson type, there is need to linearized equilibrium equations, which can be achieved through the linearization of the principle of virtual work in its continuum form. In the study, the effect of the large deflections and rotations on the displacements and the normal stress and the shear stress distributions through the thickness of the beam is investigated in detail. It is known that in the failure analysis, the most important quantities are the principal normal stresses and the maximum shear stress. Therefore these stresses are investigated in detail. The convergence studies are performed for various numbers of finite elements. The effects of the geometric non-linearity and pinned-pinned and pinned-rolled support conditions on the displacements and on the stresses are investigated. By using a twelve-node quadratic element, the free boundary conditions are satisfied and very good stress diagrams are obtained. Also, some of the results of the total Lagrangian finite element model of two dimensional continuum for a twelve-node quadratic element are compared with the results of SAP2000 packet program. Numerical results show that geometrical nonlinearity plays very important role in the static responses of the beam.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.113-121
• /
• 1995

This study deals with the quality and the optimum range of laser cutting process. Cold rolled steel sheets for automobile application were cut by a high power CO$_{2}$ laser system with beam quality of TEM$_{\infty}$ mode. Both process parameters such as travel speed and assist gas pressure, and quality factors were considered to optimize the laser cutting. It was revealed that the thinner the sheet thickness, the less effect of oxidation energy for contributing the cutting process. High speed photographs demonstrated that molten spot on the cut surface moved in a random and vigorous manner according to its viscosity and the flowing direction of assist gas, which resulted in so called striation. Laser cutting produced a very smooth surface of average roughness(Ra) about less than 1.5.mu.m at the optimum range. It was also shown that the characteristics of dross formation was influenced by the flowing durection of assist gas and the fluidity of molten metal drop..

• 소성∙가공
• /
• 제15권8호
• /
• pp.603-608
• /
• 2006

The main purpose of the present study has been placed on investigating the mechanical properties and microstructures of C-Si-Mn-V steels for cold forming manufactured by controlled rolling and cooling technology. The steels were manufactured in electric arc furnace (EAF) and casted to $160{\times}160mm$ billet. The billets were reheated in walking beam furnace and rolled to coil, the stocks were rolled by Controlled Rolling and Cooling Technology (CRCT), so rolled at low temperature by water spraying applied in rolling stage and acceleratly cooled before coiling. Rolled coils were cold drawed to the degree of 16%, 27% of area reduction respectively without heat treatment. Microstructual observation, tensile test, compression test and charpy impact tests were conducted. The mechanical properties of the steels were changed by area reduction of cold drawing and it is founded that there are optimum level of cold drawing to minimize compression stress for these steels. From the result of this study, it is conformed that $80kg_{f}/mm^{2},\;90kg_{f}/mm^{2}$ grade high strength microalloyed steel for cold forming are developed by accelerated cooling and optimum cold drawing.