• Journal of the Korean GEO-environmental Society
• /
• v.8 no.4
• /
• pp.5-11
• /
• 2007

In this study, several pullout tests were carried out under various field conditions to evaluate the pullout force of the end fixed nails. Pullout resistance force, displacement and friction force between the grouting and nail were measured in end fixed nails installed in soft rock, weathered rock and weathered soil. Furthermore, the field test were also carried out under the same condition using the conventional type nails. Based on the test results, it is concluded that the end fixed nails showed larger ultimate resistance force compared with conventional types nails, approximately two times in weathered soil and 1.6 times of weathered rock, respectively. The skin friction is also increased in end fixed type about 1.8~3.0 times. Finally, it is concluded in the base of the force transfer properties that using the end fixed nails could decrease the displacement and show a uniform resistance in entire length of nails.

• Journal of Soil and Groundwater Environment
• /
• v.9 no.3
• /
• pp.27-32
• /
• 2004

The oceanic tides have an effect on groundwater levels in coastal fractured rock aquifers. The observed groundwater table fluctuations caused by the effective stress through an aquifer are shown as sine curves similar with tidal fluctuation. To estimate a hydrogeologic parameter, tidal method is utilized with groundwater level fluctuations of two monitoring wells. Cross correlation function is used to calculate time lags between observed groundwater levels and tide, and the deeper well shows longer time lag. The storage coefficients calculated by using tidal efficiency and time lag show large differences. The storage coefficients obtained by using time lags are close to the result of slug test, and that of the deeper well shows closer value by slug test. The tidal efficiency is unsatisfied to apply in the tidal method because of an effect of phreatic aquifer and the vertical flow of groundwater through fractured confining bed. This tidal method can be an economical and effective way to define the parameter by considering the location of observation well and hydrogeologic characteristics of a coastal aquifer.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.11
• /
• pp.75-95
• /
• 2019

The numerical analysis on PHC piles socketed into weathered rocks through sandy soil layers was conducted to propose the table solution or the chart solution to obtain the mobilization capacity. The mobilization capacity was determined at the settlement of 5% pile diameter and applied a safety factor of 3.0. In order to utilize the excellent compressive strength of the PHC pile effectively, it is recommended that the allowable bearing capacity of ground would be designed to be more than the long-term allowable compressive pile load. A procedure for determining an allowable pile capacity for PHC piles socketed into weathered rocks through sandy soil layers is given by the sum of the allowable skin friction of the sandy soil layer and the weathered rock layer and the allowable end bearing capacity of the weathered rock layer. The design efficiency of the PHC pile is about 85% at the reasonable design stage in the verification of the newly proposed method. Thus, long-term allowable compressive load (P_all) level of PHC piles can be utilized in the optimal design stage.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.2
• /
• pp.1-15
• /
• 2007

A variety of revegetation methods are being utilized and developed. However, most of revegetation methods used on highway slopes in Korea are based on foreign-introduced plant varieties to stabilize road surfaces and to administer afforestation for surface covering at an earlier phase. Therefore. it results in various problems. such as failure to achieve harmony with the surrounding vegetation and 10 cause re-denudation of slopes as the foreign-in introduced plant varieties wane out from 2~3 years after hydro-seeding, etc. In addition, some of the revegetation plants seeded in the earlier phase grow excessively high, thus causes successional problems, such as to inhibit the invasion of the secondary vegetation from the surrounding areas, etc. Therefore, in this study, 160 slopes located in the nationwide express highways have been investigated and analyzed in order to produce basic data for restoration of ecological environment in slopes created on a long-term basis by investigating and analyzing locational characteristics of cut and filled slopes in express highways, status of revegetation methods, characteristics of soil and plant-ecological environment. 1. Investigation on cut and embanked slopes in express highways was carried out in the total of 160 locations, which include 108 cut slopes and 52 embanked slopes. As a whole, the most frequently used revegetation method was seed spray, which was found to be used in the total of 55 target slops investigated. 2. Planting method of Wistaria floribunda applied to some of the blasted rock zones was found to cause damages as Wistaria floribunda trailed up the surrounding vegetation and the secondary invaded trees. In order to prevent this, this method must be used only in the lowest parts of large-sized slopes. Also, it will be required to administer continuous management and maintenance in the areas already planted with this plants. 3. The areas of blasted rock and ripping rock slopes were applied with coir net (net + seeding) method. However, many of these areas failed in achieving ground covering. Most areas where revegetation was in progress, they were covered with Eragrostis curvula(Weeping lovegrass) only. In areas with soil, such as decomposition of granite, where afforestation is difficult. In this slopes, soil base must be improved by hrdroseeding with thin-layer vegetation base application methods in order to achieve success in afforestation with native plants. 4. Woody species, rather than herb species, are more helpful in stabilization of slope surfaces. Therefore, it is important to be able to grow and protect woody species on highway slopes. Growth of woody vegetation is most largely influenced by soil depth. Thus, when hydro-seeding woody plants, it is recommended to apply at the upper layer of the slopes, which is capable to sufficiently provide the fundamentals required in plant growth.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.9
• /
• pp.47-56
• /
• 2004

A new fragmentation model, called the GRS (the generation model of weathered residual soils) model, was proposed in this study, This model could identify the formation of a residual soil. This model is based on the phenomena that as the soil was weathered more highly, soil particles were smaller and pores were more expanded simultaneously. The possibility of fragmentation, $P_F,$ which was based on the fractal theory, was introduced in this model. There were some fundamental notions in the GRS model that soil particles were generated as the rock is fragmented, and the fragmentation of the rock was performed step by step. The $P_F,$ of the rock was not constant at each fragmentation steps. As a result of application on the GRS model, there were more residue where $P_{Fi}s$ were small at any particle size. There was a S-shape of PSD curve at the concave shape of $P_{Fi},$ and the PSD curve goes to a gaped graded curve at the convex shape of $P_{Fi}.$ The shape of PSD curve was concave in the case of small $P_{Fi}s.$ The value of $P_{Fi}$ increased with the coefficient of uniformity $(C_u)$ and the fragmentation fractal dimension $(D_r),$ but had no relation with the coefficient of gradation $(C_C)$.

• Geomechanics and Engineering
• /
• v.8 no.5
• /
• pp.663-674
• /
• 2015

Many seismically vulnerable regions in India and worldwide are located on deep soil deposits which extend to several hundred meters of depth. It has been well recognized that the earthquake shaking is altered by geological conditions at the location of building. As seismic waves propagates through uppermost layers of soil and rock, these layers serve as filter and they can increase the duration and amplitude of earthquake motion within narrow frequency bands. The amplification of these waves is largely controlled by mechanical properties of these layers, which are function of their stiffness and damping. Stiffness and damping are further influenced by soil type and thickness. In the current study, an attempt has been made to study the seismic site response of deep soils. Three hypothetical homogeneous soil models (e.g., soft soil, medium soil and hard soil) lying on bedrock are considered. Depth of half space is varied from 30 m to 2,000 m in this study. Controlled synthetic motions are used as input base motion. One dimensional equivalent linear ground response analyses are carried out using a computer package DEEPSOIL. Conventional approach of analysing up to 30 m depth has been found to be inadequate for deep soil sites. PGA values are observed to be higher for deeper soil profiles as compared to shallow soil profiles indicating that deeper soil profiles are more prone to liquefaction and other related seismic hazards under earthquake ground shaking. The study recommends to deal the deeper soil sections more carefully for estimating the amplification factors for seismic hazard assessment at the surface.

• Korean Journal of Environment and Ecology
• /
• v.37 no.1
• /
• pp.1-12
• /
• 2023

We analyzed the distribution area of debris slopes in Mudeungsan (Mt. Mudeung) National Park by comparing aerial photos of the past (1966) and the present (2017) and identified the vegetation characteristics that affect the change in the area of the debris slopes by investigating the vegetation status of the debris slopes and the surrounding areas. The area of debris slopes in Mt. Mudeung appears to have been reduced to a quarter of what it used to be. Debris slopes here have decreased at an average rate of 2.3 ha/yr over 51 years by vegetation covers. Notably, most of the small-area debris slopes in the low-inclination slopes disappeared due to active vegetation coverage. However, there are still west-facing, south-west-facing, south-facing, and large-area debris slopes remaining because the sun's radiant heat rapidly raises the surface temperature of rock blocks and dries moisture, making tree growth unfavorable. Because of these locational characteristics, the small-scale vegetation in the middle of Deoksan Stony Slope, which is the broadest area, showed distinct characteristics from the adjacent forest areas. Sunny places and tree species with excellent drying resistance were observed frequently in Deoksan Stony Slope. However, tree species with high hygropreference that grow well in valleys with good soil conditions also prevailed. In some of these places, the soil layer has been well developed due to the accumulation of fine materials and organic matter between the crevices of the rock blocks, which is likely to have provided favorable conditions for such tree species to settle and grow. At the top of Mt. Mudeung, on the other hand, the forest covered the debris slopes, where Mongolian oaks (Quercus mongolica) and royal azaleas (Rhododendron schlippenbachii), which typically grow in the highlands, prevailed. This area was considered favorable for the development of vegetation for the highlands because the density of rock blocks was lower than in Deoksan Stony Slope, and the soil was exposed. Moreover, ash trees (Fraxinus rhynchophylla) and Korean maple trees (Acer pseudosieboldianum) that commonly appear in the valley areas were dominant here. It is probably due to the increased moisture content in the soil, which resulted from creating a depressive landform with a concave shape that is easy to collect rainwater as rock blocks in some areas fell and piled up in the lower region. In conclusion, the area, density of the rock blocks, and distribution pattern of rock block slopes would have affected the vegetation development and species composition in the debris slope landform.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.11 no.2
• /
• pp.28-39
• /
• 2008

This study was conducted to evaluate the rehabilitation measures and select appropriate tree species and rehabilitation methods for rehabilitating the rock desert areas in Guizhou, China. The study was carried out during the periods from 2003 to 2006 and results are as follows. Afforestation site is classified as a dolomite sandstone hilly country, a halfstony hilly country, a karst physiognomy, a rock desertification farmland and an latent rock desertification farmland by soil type and rock desertification status. Total afforestation area of Xuiwen is 1,300ha and afforestation area of a dolomite sandstone hilly country, a halfstony hilly country, a karst physiognomy, a rock desertification farmland and an latent rock desertification farmland are respectively 104.0ha (8.0%), 146.6ha (11.3%), 200.5ha (15.4%), 705.7ha (54.3%) and 143.2ha (11.0%). Planted tree species were selected by five site types. Robinia pseudoacacia, Chamaecyparis obtusa, Thuja orientalis, Cupressus duclouxiana and Juniperus chinensis L. var. chinensis were planted in a dolomite sandstone hilly country and Choerospondias axillaris and Robinia pseudoacacia were planted in a halfstony hilly country. Cupressus duclouxiana, Zanthoxylum bungeanum, Lonicera fulvotomentosa, Ilex kudincila, Quercus aliena, Quercus variabilis, Choerospondias axillaris, Koelreuteria bipinnata, Cryptomeria japonica, Cinnamomum camphora and Cinnamomum bodinieri were planted in a karst physiognomy. Cupressus duclouxiana, Toona sinensis, Robinia pseudoacacia, Lonicera fulvotomentosa, Eucommia ulmoides, Ilex kudincha. Zanthoxylum bungeanum and Magnolia officinalis were planted in a rock desertification farmland. Lonicera fulvotomentosa, Juglans sinensis, Pyrus pyrifolia, Choerospondias axillaris, Prunus salicina and Diospyros Kaki was planted in an latent rock desertification farm land. Robinia pseudoacacia showed high survival rate in 2004 and 2005, but Zanthoxylum bungeanum and Cinnamomum camphora showed slightly low survival rate in 2004. Survival rate of planting species in 2005 was over 80% because some species which showed low survival in 2004 were changed with other species and a proper afforestation method was applied. Growth rate of tree species was evaluated by height and diameter growth rate. Cupressus duclouxiana showed a highest height growth rate in 2004. Toona sil1ensis, Choerospondias axillaris, Koelreuteria bipinnata, and Cinnamomum camphora showed almost 100% height growth rate in 2005, although they showed a negative height growth rate in 2004. Robinia pseudoacacia showed a good growth rate in the rock desertification farmland and the halfstony hilly country so it could give a commercial benefit like honey as well as an afforestation effect.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.6
• /
• pp.97-102
• /
• 2007

Though the stability analysis of soil slopes widely employs the limit equilibrium method, the study on the jointed rock slopes must consider the direction of joint and the characteristics of Joint at the same time. This study analyzes the result of the change in the factors which show the characteristics of discontinuity and the shape factor of rock slopes, and so on, in an attempt to validate the propriety as to the interpretation of jointed rock slope stability which uses the general finite element program. First, the difference depending on the flow rules was compared, and the factor effect study was conducted. The selected independent variables included the direction of joint which displays the mechanical characteristics of discontinuity, adhesive cohesion, friction angle, the inclination and height of rock slope which reveal the shape of slope and surcharge load. And the horizontal displacement was numerically interpreted at the 1/3 point below the slope, a dependent variable, to compare the relative degree of factor effects. The findings of study on factor effects led to the validation that the result of horizontal displacement for each factor satisfied various engineering characteristics, making it possible to be applied to stability interpretation of jointed rock slope. A modelling is possible, which considers the application of the result of real geotechnical surveys & laboratory studies and the non-linear characteristics when designing the rock slope. In addition, the stress change which may result from the natural disaster, such as precipitation, and the construction, can be expressed. Furthermore, as the complicated rock condition and the ground supporting effect can be considered through FEM, it is considered to be very useful in making an engineering decision on the cut-slope, reinforcement and so on.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.10a
• /
• pp.98-107
• /
• 2000

Free-field ground motion during earthquake is significantly affected by the local site conditions and it is essential for the seismic design to perform the ground response analysis In this study, ground response analyses based on the equivalent linear method were carried out to evaluate the effects of various ground conditions on the site amplification. Four major factors including the depth of the site(very soft and dense soil), the impedance ratio between soil layer and bed rock, linear analysis versus equivalent linear analysis, and the location of soft soil layer were deeply discussed. Based on the analysis results, the importance of various local site conditions on the site amplification was emphasized.