• Tunnel and Underground Space
• /
• v.10 no.1
• /
• pp.45-58
• /
• 2000

Cyclic shear test system, which is capable of measuring flow rate inside rock joint, was established to investigate the hydraulic behavior of rough rock joints under various loading conditions. Laboratory hydraulic tests during compression and shear were conducted for artificial rough rock joints. Prior to tests, aperture characteristics of specimens were examined by measuring surface topography. Permeability changes under compression were well approximated with several hydraulic model. Hydraulic behavior conformed to dilation characteristics in the first stage, and permeability increased with increase of dilation. As the shear displacement progressed, flow rate became somewhat constant due to gouge production and offset of apertures. Hydraulic behavior under cyclic shear loading was also influenced by the degradation of asperities and gouge production. In addition. the relation between hydraulic aperture and mechanical aperture under compression and shear loading was investigated and compared.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.4
• /
• pp.375-385
• /
• 2013

This study evaluates correlation between petrographic characteristics and weathering grade of low-graded metasedimentary rocks mainly consisting of phyllite. Weathering grade of rock material was determined based on the results of geological survey. The Schmidt hammer test was carried out to obtain estimates of strength of rock materials. Point counting and microscopic observation were also conducted to analyze mineral composition and to measure spacing of foliation for 9 rock specimens. As a result of microscopic analysis, as the weathering grade was lower, the quartz was found more in quantity, consequently making rock stronger against weathering process. On the other side, lower weathering grade of rock resulted in less content of mica which is weak against weathering process. In addition, the rock materials with closer foliation spacing are found to be weaker in strength and have higher weathering grade.

• Geomechanics and Engineering
• /
• v.24 no.4
• /
• pp.349-358
• /
• 2021

The Brazilian test has been widely used to determine the indirect tensile strength of rock, concrete and other brittle materials. The basic assumption for the calculation formula of Brazilian tensile strength is that the elastic moduli of rock are the same both in tension and compression. However, the fact is that the elastic moduli in tension and compression of most rocks are different. Thus, the formula of Brazilian tensile strength under the assumption of isotropy is unreasonable. In the present study, we conducted Brazilian tests on flat disk-shaped rock specimens and attached strain gauges at the center of the disc to measure the strains of rock. A tension-compression bi-modular model is proposed to interpret the data of the Brazilian test. The relations between the principal strains, principal stresses and the ratio of the compressive modulus to tensile modulus at the disc center are established. Thus, the tensile and compressive moduli as well as the correct tensile strength can be estimated simultaneously by the new formulas. It is found that the tensile and compressive moduli obtained using these formulas were in well agreement with the values obtained from the direct tension and compression tests. The formulas deduced from the Brazilian test based on the assumption of isotropy overestimated the tensile strength and tensile modulus and underestimated the compressive modulus. This work provides a new methodology to estimate tensile strength and moduli of rock simultaneously considering tension-compression bi-modularity.

• Tunnel and Underground Space
• /
• v.21 no.1
• /
• pp.33-40
• /
• 2011

This study focuses on having a temperature and water pressure effects on the change of material properties of rocks. Granite and limestone specimens from Gagok Mine were thermally treated with predetermined temperatures of 200, 300, 400, 500, 600 and $700^{\circ}C$ (excepting $700^{\circ}C$ for limestone) to estimate the reduction of material properties of rocks caused by heat. Specific gravity, effective porosity, elastic wave velocity, uniaxial compressive strength, Young's modulus and Poisson's ratio for pre-heated specimens were measured. With increasing temperature, material properties of both rock specimens change sequentially. Significant changes of specific gravity, effective porosity and elastic wave porosity occur above $400^{\circ}C$ for granite and $300^{\circ}C$ for limestone. Changes of uniaxial compressive strength, Young's modulus and Poisson's ratio seem to be similar to those of physical properties. GSI of 500, 600 and $700^{\circ}C$ specimens inferred by using uniaxial compressive strength and Young's modulus of preheated granite specimens is found to be 81, 66 and 58 each. In case of pre-heated limestone specimens of 400, 500 and $600^{\circ}C$, the corresponding GSI is 76, 71 and 65 each. 500, 600 and $700^{\circ}C$ granite specimens and 400, 500 and $600^{\circ}C$ limestone specimens were pressurized to 7.5 MPa and their effective porosity, elastic wave velocity, uniaxial compressive strength and Young's modulus were measured. The average value of material properties (mentioned above) of 500, 600 and $700^{\circ}C$ granite specimens under water pressure compared with material properties of non-pressurized pre-heated specimens exhibits the reduction of 7.6, 11.3 and 14.9%, respectively. In case of 400, 500 and $600^{\circ}C$ limestone specimens under water pressure, the average value of material properties decreases by 8.2, 13.8 and 21.9%, respectively.

• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.169-179
• /
• 2003

Anisotropic shear strength of rock joints is studied based on the artificially fractured specimens using experimental and analytical methods. Series of direct shear tests are performed to obtain the strength, stiffness and friction angle of joints under various low normal stresses and shearing directions. The results of shear strength and stiffness show anisotropic value according to shearing direction under low normal stress specially less than 2.45 MPa. But, the effect of joint roughness on strength decreases with increasing normal stress. To estimate more effectively the peak shear strength under low normal stress, the modified Barton's equation is suggested.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.5
• /
• pp.517-528
• /
• 2012

Inserting a nozzle assembly into a removed cutting space during a continuous cutting operation is necessary in rock excavation using an abrasive waterjet. In this study, a combined two nozzle assembly is used to secure enough removal width. The shape of the cut space is affected by the geometric parameters (standoff distance, nozzle angle, and vertical distance between the nozzle tips) of the combined nozzle assembly. Abrasive waterjet cutting tests are performed with various geometric parameters for granite rock specimens. Optimized geometric parameters for the nozzle inserting process are determined and verified through the experimental tests.

• Tunnel and Underground Space
• /
• v.20 no.5
• /
• pp.390-398
• /
• 2010

The time-dependent behaviour of rock is very important characteristics which can be utilized as basic input data for underground mine design or in predicting a long-term stability of underground rock mass structures. In this study, creep tests under uniaxial compression were carried out for the granite specimens sampled in Gagok Mine. Burgers model, Griggs and Singh creep laws were used to simulate the measured creep strain. Through comparing the measured creep behaviour with the approximated creep behaviors from Burgers model, Griggs and Singh creep laws, it is shown that Griggs creep law results in the best approximation of granite in Gagok Mine.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.3
• /
• pp.167-181
• /
• 2021

New type of rock excavation method using a waterjet system is being developed to secure economic feasibility and to reduce vibrations during excavation. In waterjet rock excavation, overlapping of cutting width is essential for high efficiency. In this study, cutting experiments for granite specimens were performed using abrasive waterjet system according to the overlapping ratio and standoff distance. Based on the experimental results, the granite cutting performance was analyzed according to the overlapping ratio. In addition, removal shapes of the cross-section were analyzed in terms of the cutting depth, width, and volume after waterjet cutting. When the overlapping ratio is less than 58%, rock specimens are partially removed due to the insufficient overlapping ratio. However, when the overlapping ratio exceeds 67%, overcutting phenomenon is observed. For the partial overlapping ratio (i.e., 25~75%), cutting efficiency is increased in the removal volume. This study is expected to be used as the important basic data for determining the optimum overlapping ratio when the waterjet system is applied for rock excavation.

• Computers and Concrete
• /
• v.17 no.1
• /
• pp.129-140
• /
• 2016

Basalt is a type of volcanic rocks, grey to black in colour, contains less than 20% quartz, 10% feldspathoid, and at least 65% of the feldspar of its volume. Basalt is considered an igneous rock with fine grains due to the rapid cooling of lava. Basaltic rocks have been widely used as aggregate for various purposes. The study presented in this paper was carried out on basalts that are widespread in the Madeira Island of Portugal and that comprise the major source of local crushed rock aggregates. This paper discusses an experimental programme that was carried out to study the effects of basaltic aggregate on the compressive strength and modulus of elasticity of concrete. For this purpose, cylinder specimens with $150{\times}300mm$ dimensions and prism specimens with $150{\times}150{\times}375mm$ dimensions were cast. The experimental programme was carried out with several concrete compositions belonging to strength classes C20/25, C25/30, C30/37, C40/50 and C60/75. The Eurocode 2 indicates the modulus of elasticity should be 20% higher when the aggregates are of basaltic origin, however results showed significant differences and a correction is proposed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.2
• /
• pp.184-192
• /
• 2002

The purpose of this study was to investigate the abrasion resistance and surface roughness of conventional dental stones and improved dental stones and newly developed dental stones. Materials included in this study were several dental stones and newly developed dental stone; 2 type III. 6 type IV (including newly developed dental stone). 1 type V Ten specimens for each material, total ninety specimens were made. Each specimen was subjected to 50 complete cycle abrasion under constant load 0.42N at speed or 6mm per sec. The depth after abrasion test was measured for each specimen. Surface roughness before and after abrasion test was compared. The results were as follows ; 1. The resin containing die materials such as Tuff Rock and Resin Rock had superior abrasion resistance. 2. Type IV, V dental stone exhibited greater abrasion resistance than Type III dental stone. 3. The results or the surface roughness showed similar pattern with the abrasion resistance.