• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2007년도 공동학술대회 논문집
• /
• pp.291-296
• /
• 2007

We measured potential waveform of load, displacement, micro electric signal generated by rock and mortar fracture using PXI A/D Converter. The rock type used for measurement was used granite, limestone and sandstone, and mortar specimen. we made measuring equipment of physical properties to confirm basic information of physical properties, measured physical properties of rock engineering, electric resistivity and seismic velocity. Potential waveform system was built using PXI A/D Converter and measured potential waveform of load, displacement, micro-electric signal generated using this during uniaxial compressive test by the specimen finished such test of physical properties. Using the saturated rock and mortar specimen, micro electric signal increased, and It didn't increase a signal in dried rock and mortar specimen according as load and strain rate increases. But signal also increased in saturated or dried specimen in case of sandstone. It was possible to check the close correlation relationship the signal and fracture behavior by a compressive load as the signal of fracture position was increased bigger than the other position. It was also possible to check the correlation relationship between physical properties and micro geo-electric signal.

• 한국지형학회지
• /
• 제23권1호
• /
• pp.1-16
• /
• 2016

This study estimates relationships between physical and chemical weathering indices of various rock types and topographical relief. Physical weathering properties such as rock strength and joint and chemical weathering indices such as the $SiO_2/Al2O_3$, CIA and WPI were analyzed from 18 rock outcrops in mountain and valley areas consisting of 9 rock types. The results indicate that the elevation and relief of topography increase physical strength of rock increases. It can be suggested that the total r(rock-mass strength rating) and R(rock rebound strength by Schmidt Hammer) are most useful indices as a quantitative weathering property factor to explain formative causes of topographical relief. The results also suggest that rock types such as sandstone, granite, gneiss and schist are most suitable to explain meaningful difference in topographical relief with the physical and chemical weathering indices.

• 지질공학
• /
• 제34권1호
• /
• pp.25-38
• /
• 2024

본 연구에서는 해수와 산성증류수가 암석 풍화에 미치는 영향을 파악하기 위하여 실내인공풍화가속실험을 수행하였다. 70℃의 해수와 산성증류수(pH 3)를 이용하여 총 45회의 동결-융해 실험을 통하여 5종의 유천층군 화산암에 대하여 화학적·물리적 풍화를 모사하였다. 실내인공풍화가속실험 15회와 45회에 각각 물리적 물성과 일축압축강도를 측정하여 풍화 진행에 따른 물성 변화를 추적한 결과, 물리적 물성의 열화는 대부분은 초기 15회 실험에서 발현되었으며, 산성증류수가 해수보다 물리적 물성 변화에 더 많은 영향을 미치는 것으로 파악되었다. 실내인공풍화가속실험에 따른 암종별 일축압축강도의 차이를 통계적으로 평가하기 위하여 분산분석법을 사용하였다. 45회 실험 이후의 대조군에 대한 실험군 시료의 일축압축강도의 감소율은 암종과 물리적 물성 변화 추이와 상관없이 유사하게 나타났지만, 물리적 물성 변화와는 달리, 산성증류수보다 해수가 일축압축강도 변화에 더 많은 영향을 미치는 것으로 파악되었다.

• Geomechanics and Engineering
• /
• 제11권2호
• /
• pp.197-209
• /
• 2016

Clayey rock has large clay mineral content. When in contact with water, this expands considerably and may present a significant hazard to the stability of the rock in geotechnical engineering applications. This is particularly important in the present work, which focused on mitigating some unwelcomed properties of clayey rock. Changes in its physical properties were simulated by subjecting the rock to a low voltage direct current (DC) using copper, steel and aluminum electrodes. The modified mechanism of the coupled electrical and chemical fields acting on the clayey rock was analyzed. It was concluded that the essence of clayey rock electrochemical modification is the electrokinetic effect of the DC field, together with the coupled hydraulic and electrical potential gradients in fine-grained clayey rock, including ion migration, electrophoresis and electro-osmosis. The aluminum cathodes were corroded and generated gibbsite at the anode; the steel and copper cathodes showed no obvious change. The electrical resistivity and uniaxial compressive strength (UCS) of the modified specimens from the anode, intermediate and cathode zones tended to decrease. Samples taken from these zones showed a positive correlation between electric resistivity and UCS.

• 한국지형학회지
• /
• 제23권3호
• /
• pp.27-39
• /
• 2016

This study statistically investigates relationships between physical properties of rocks and topography by measuring and analyzing section, topographical and measured parameters of 58 bedrock outcrops at areas covered by gneiss, schist, granite, andesite, sandstone and limestone in the Korean Peninsula. Multiple linear regression analysis suggests that the joint spacing, joint continuity, weathering grade and maximum joint width of rocks among the measured parameters are related to the topographical parameters with statistical significances. Therefore, this study suggests that rock properties such as joint spacing, joint continuity, weathering grade and maximum joint width seem to greatly influence topography, although various factors can affect topographical parameters.

• 터널과지하공간
• /
• 제6권3호
• /
• pp.239-244
• /
• 1996

Cracks have influence on the physical and mechanical and, more importantly, on the engineering properties of the rock. Physical properties including the volumetric deformation coefficient, electrical resistivity, seismic wave velocity, and the mechanical properties such as the elastic constants and strength of rock are affected significantly by the presence of cracks of various sizes. An experimental program was undertaken to investigate the effect of a finite line crack on the diffraction of the plane compressional wave. Horizontal and vertical components of displacement and acceleration curve were obtained using a single-source and multi-receivers system. A theoretical model from numerical analysis implementing the finite element method was compared with the measured data.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.557-560
• /
• 2003

Some well-known artificial weathering tests such as freezing-thawing, acid immersion, and salt crystallization are adopted to examine the change of rock properties during the processes of artificial weathering. Granites and other rock types of limestone, marble and basalt collected from different quarries in south Korea were sampled for this study. All tests were performed up to 30 cycles and physical properties were measured after experiencing every ten cycles of artificial weathering tests. During the tests, the variation trends of rock properties were too variable to draw generalized variation patterns but it can be concluded that weathering agents have different effect on rock properties depending on weathering circumstance and time. Even in short terms of salt crystallization tests, some rocks were severely deformed and then burst, and in the early stages of salt weathering, recrystallized salts filling pores and cracks in rocks could be a important factor affecting rock properties.

• 터널과지하공간
• /
• 제14권4호
• /
• pp.261-268
• /
• 2004

The main objectives of this study are to investigate the anisotropic characteristics of rocks and to evaluate the relationships between physical properties. A series of experiments were performed in three mutually perpendicular directions for three rock types, which are granite, granitic gneiss and limestone. The relationships of measured physical properties were evaluated. The results of ultrasonic wave velocity measurement show that granite of three rock types gives the largest directional difference, and that the wave velocity in a plane parallel to a transversely isotropic one is dominantly faster than that in a subvertical or vertical plane. It implies that ultrasonic wave velocity for rock could be used as a useful tool for estimating the degree of anisotropy. The ratio of uniaxial compressive strength to Brazilian tensile strength ranges approximately from 13 to 16 for granite. from 8 to 9 for granite gneiss, and from 9 to 18 for limestone. The directional differences for granite and granitic gneiss are very small, and on the other hand, is relatively large for limestone. It is suggested that strength of rock makes quite difference depending on the rock types and loading directions, especially for the anisotropic rocks such as transversely isotropic or orthotropic rocks. The ratio of uniaxial compressive strength to point load strength index ranges from 18 to 20 for granite, from 17 to 19 for granitic gneiss, and from 21 to 24 for limestone. These results show that point load strength index makes also a difference depending on rock types and directions. Therefore. it should be noted that the ratio of uniaxial compressive strength to point load strength index could be applied to all rock types. Uniaxial compressive strength shows relatively good relationship with point load strength index, Schmidt hammer rebound value, and tensile strength. In particulat, point load strength index is shown to be the best comparative relationship. It is indicated that point load test is the most useful tool to estimate an uniaxial compressive strength indirectly.

• 자원환경지질
• /
• 제32권1호
• /
• pp.1-11
• /
• 1999

In the last decade, the supply of natural aggregates has been continuously increased due to the other types of aggregates. In general, aggregates constitute 70-80% of the total volume of concrete, so the quality of aggregates is main factor controlling physical characteristics of concrete. For this reason, physical properties of aggregate according to different rock types were studied. The majority of crushed aggregates is taken out of granite, gneiss, sandstone, andesite, basalt and so forth. The physical properties of these rock types were tested and most of them fell within the acceptable limit on the base of Korean standard regulation. The major lithology of the crushed aggregates is granite and gneiss, both of which are marked for more than 50% of total lithology thpes in Korea. A to the physical properties of granite, the high specific gravity coincides with low porosity, low absorption ratio, while the abrasion and soundness index show, in general, no specific trend. It has been assumed that slight differences of the physical properties of granite aggregates are related with those of the mineral composition, grain size, and so on. In comparison to granite, the physical properties of gneiss have little correlation one after another. This trend is related to different mineral composition, grain size and typical sheet fractures typically prevailing in the texture of gneiss. Spatial pattern of physical properties shows that high specific gravity of granite coincides only with low porosity and absorption ratio in all provinces except Cheolla province, and high specific gravity of gneiss coincides with low porosity and absorption ratio only in Cheolla and Gandwon provinces.

• 터널과지하공간
• /
• 제18권5호
• /
• pp.317-327
• /
• 2008

산악지형이 많은 국내 여건으로 인해 많은 암반구조물이 건설되고 있으며, 이와 관련하여 암석물성시험을 포함한 수많은 지반조사가 수행되었다. 본 연구는 국내 암석의 역학적 특성자료의 데이터베이스화를 위한 기본 연구로서, 국기공인시험기관에서 수행되었던 시험자료 약 2000 개에 대해 역학적 상관성에 대해 분석하였다. 효용성있는 데이터베이스를 구축하기 위해서는 신뢰성있는 자료의 축적 뿐 아니라 규격화된 정보를 토대로 체계적인 관리가 필요할 것이다.