• 문화기술의 융합
• /
• 제8권1호
• /
• pp.507-512
• /
• 2022

연구 대상은 교량 접속도로 절취비탈면으로서 파괴 위험 가능성이 큰 중생대 경상누층군 퇴적암 비탈면이다. 비탈면의 구성 암석은 사암, 미사암 및 암맥이며, 불연속면은 층리와 전단절리, 인장절리 및 암맥 접촉면이 발달한다. 구간별로 파괴의 유형과 규모는 암석의 종류와 불연속면의 배향에 따라 다양하나 평면파괴가 우세하고, 파괴암체의 크기는 대부분 1m³ 이하이다. face-mapping 자료, SMR, 암석의 물성·역학시험, 구간별 지질횡단면도 분석 및 한계평형해석으로 종합·검토한 결과, 대표적 단면 모두 건기 시와 우기 시의 허용안전율에 크게 미달하여 대책공법이 필요 하였다. 따라서 경제성, 효율성, 현장 특성, 등을 고려하여 비탈면 내 구간과 위치에 따라 대책공법 안을 제안하였고 대책공법을 적용한 후 비탈면의 건기 및 우기 시의 안전율은 모두 허용안전율을 상회 하였다. 특히, 법면 face-mapping 자료와 법면에 수직인 여러 대표 구간의 지질횡단면도, 그를 기본도면으로 사용한 한계평형해석 및 대책공법 제시는 비탈면의 객관적인 해석 및 안정성 검토의 합리적인 도구가 될 것으로 예상한다.

• 한국지반공학회논문집
• /
• 제15권6호
• /
• pp.3-16
• /
• 1999

본 논문은 새로 개발된 파괴형태를 고려한 암반사면의 신뢰도해석 모델의 검증을 위하여 예제를 통한 민감도해석을 수행하였고 그 결과를 수록하였다. 민감도분석에 이용된 매개변수는 암반 불연속면의 공학적 특성 (불연속면의 방향 및 강도),하중조건 및 암반사면의 기하학적 형상 등이다. 확률론적 해석에서 고려할 수 있는 불연속면의 방향 및 마찰각의 통계적 특성이 파괴형태를 고려한 암반사면의 안정에 큰 영향을 보였다. 암반사면의 안정은 굴착면의 방향에 가장 민감하였다. 예제분석을 통하여 개발된 파괴형태를 고려한 암반사면의 신뢰도모델은 암반사면의 안정성 조사에 성공적으로 적용할 수 있었다.

• 터널과지하공간
• /
• 제13권4호
• /
• pp.245-259
• /
• 2003

Refering to the articles "Squeezing rocks in tunnels(Barla, 1995)" and "Tunnelling under squeezing rock conditions(Barla 2002)" this article deals with technologies for design, stability analysis and construction of the tunnel being driven in the squeezing rock mass. The definition of this type of behavior was proposed by ISRM(1994). The identification and quantification of squeezing is given according to both the empirical and semi-empirical methods available to anticipate the potential of squeezing problems in tunnelling. Based on the experiences and lessons learned in recent years, the state of the art in modem construction methods was reported, when dealing with squeezing rock masses by either conventional or mechanical excavation methods. The closed-form solutions available for the analysis of the rock mass response during tunnel excavation are described in terms of the ground characteristic line and with reference to some elasto-plastic models for the given rock mass. Finally numerical methods were used for the simulation of different models and for design analysis of complex excavation and support systems, including three-dimensional conditions in order to quantify the influence of the advancing tunnel face to the deformation behavior of the tunnel.

• 터널과지하공간
• /
• 제5권2호
• /
• pp.104-113
• /
• 1995

Shear strength of the discontinuity on which the pre-failure of rock slope was occurred during surface excavation was measured through the direct shear test using core samples obtained in-situ. Internal friction angle was increased as the roughness of discontinuity surface(JRC) was increased. Results of the tilt test using core samples of higher JRC also showed very similar trend as those of the direct shear test. When the samples replicated from natural cores were used int he tilt test, results of friction angles showed almost perfect continuation of the residual friction angles from the direct shear test. However, when the gouge material existed in the discontinuity the internal friction angle strongly depended upon the rate of filling thickness to the height of asperity irrespective of the JRC. Based on the results of both direct shear test and tilt test internal friction angle and cohesion of discontinuity, which reflect the in-situ conditions fo pre-sliding failure and also can be used for the optimum design of support system, were assessed. Two kinds of support measures which were expected to increase the stability of rock slope were considered; lowering of slope face angle and installation of rock cable. But, it was found that the first method might lead to more unstable conditions of rock slope when the cohesion of discontinuity plane was negligibly low and in that case the support systems of any kind which could exert actual resisting force were needed to ensure the permanent stability of rock slope.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.930-937
• /
• 2004

In tunnel blasting, rock damage and overbreak at excavation limits are strongly related to stability of the tunnel and cost for rock support, and also affect to maintenance after tunnel construction. In this study, many field tests and measurements have been carried out in highway tunnels so that discordance between blast design and practical production blasting could be settled and actual methods of over break control could be proposed through the understanding of the problems in existing blasting patterns. Test blasting in tunnel was carried out many times in two tunnel sites. Also, long hole blasting longer than existing blasting pattern was executed for good grade of rock mass whose RMR value is more than 60. Using the results of test blasting, new standard blasting patterns for two lane tunnel were proposed. As a result of profile measurement after blasting, drilling is a major factor of overbreak. And then the methods for minimizing overbreak were adapted in new blasting patterns.

• 터널과지하공간
• /
• 제20권6호
• /
• pp.421-433
• /
• 2010

암반면 평가를 위한 디지털 영상 계측 시 획득된 영상정보는 조명의 광량과 조명색 그리고 카메라의 촬영조건 등에 따라 달라지며, 왜곡된 영상정보는 객관적인 암반 평가를 어렵게 하는 주요한 원인이 된다. 본 연구에서는 다양한 설정 조건 하에서 획득된 디지털 영상정보의 색보정을 통해 자연광 상태에서의 고유한 영상정보로 복원하기 위한 실험 및 분석을 수행하였으며, 최종적으로 영상정보 최적화를 위한 조명 조건 및 카메라 설정 방안을 제시하였다.

• 터널과지하공간
• /
• 제33권1호
• /
• pp.1-9
• /
• 2023

국내 터널현장에 도입된 드럼타입 로드헤더의 작동방식 및 현장 운영 사례를 소개하였다. 축방향 타입과 횡방향 타입의 작동에 따른 절삭력과 반력의 방향을 분석하였다. 텔레스코픽 실린더의 사용 유무에 따른 터널면 형성의 차이점을 설명하였다. 실린더를 사용하지 않는 경우, 오목한 작은 반경의 터널면이 형성되어 터널면을 좌우로 구분하여 굴진하는 것으로 조사되었다. 그리고 국내 경암 터널 굴착환경에서 썸핑과 쉬어링 공정의 적용방안을 도해적으로 설명하고, 굴착공정에 대한 기존 설명자료를 일부 보완하였다.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2007년도 춘계학술발표회 논문집
• /
• pp.93-96
• /
• 2007

LIDAR is a relatively new technological tool that can be used to accurately georeference terrain features, and also is becoming an important 3D mapping tool in GIS. In this study it is described the capabilities of terrestrial LIDAR that was used to build a 3D terrain model of extremely steep rock face, along with the useful data and examples of contributions terrestrial lidar has made to outcrop studies. For this, High-resolution terrestrial lidar acquisition, processing, interpretation are discussed and applied to mapping of geological surfaces in three dimensions. We expected that lidar is a tool with which we can improve our current field methods and quantify the observations geologists make.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.210-220
• /
• 2005

We have analyzed the stability for cut-slopes at main street 3-2 line section in Pa-ju local industrial complex. After studying an additional boring test, laboratory test and face mapping etc., we have determined the extent of reinforcement, slope inclinations and soil strength parameter from the analysis of test results. After changing the inclination of slopes for ground limit and carrying out the analysis of slope stability, we applied the Mass Nailing Method to the site because of need for reinforcement to soil and weathered rock slopes. In slope for soft and hard rock sections, we also reinforced the sections that are difficult to obtain the safety without reinforcement in alteration zone.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.871-876
• /
• 2010

When surface Concrete Face Rock fill Dam constructs than existent center core type rock fill dam, it is much prevalent form in domestic these day by quality control of that is profitable and weather condition etc. of coreZone. C.F.R.D is less research about seismic survey(Refractional Seismic Prospectin, Resistivity Prospecting) of levee body than fill dam. Thus as C.F.R.D seismic survey is less, safety of that consist is short most development flue is high reason. That is not checking target of minuteness safety diagnosis and so on by short operation period. Wish to analyze inquiry incidental and difference with center core type dam and acquire C.F.R.D preservation administration upper necessary inquiry condition forward hereafter.